The headlight ECU sub-assembly operates the low beam fan to cool the headlight LED unit in order to prevent the headlight LED unit from overheating.
Illuminates the low beam headlights and continuously operates the low beam fan.
The headlight ECU sub-assembly monitors the pulse signals from the FANP terminal when the low beam fans are operating.
If B243D or B243E is output, the headlight ECU sub-assembly performs low beam headlight dimming control.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B243D | Left Low Beam Fan Malfunction | Detection condition:
All of the following conditions are met: -
Ignition switch ON -
Low beam headlights on Malfunction status:
Fan speed signals from the low beam fan of less than 2250 rpm are continuously detected Malfunction duration:
4 seconds or more |
·
Headlight LED unit assembly LH ·
Headlight unit assembly LH ·
Headlight ECU sub-assembly LH |
HL AutoLeveling |
| B243E | Right Low Beam Fan Malfunction | Detection condition:
All of the following conditions are met: -
Ignition switch ON -
Low beam headlights on Malfunction status:
Fan speed signals from the low beam fan of less than 2250 rpm are continuously detected Malfunction duration:
4 seconds or more |
·
Headlight LED unit assembly RH ·
Headlight unit assembly RH ·
Headlight ECU sub-assembly RH |
HL AutoLeveling (Sub) |
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Operate the light control switch to turn on the low beam headlights and wait 4 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.
Check for DTCs.
DTC B243D and B243E are not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (DTC B243D is output) | B |
| NG (DTC B243E is output) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
| *a | Component without harness connected
(to Headlight ECU Sub-assembly LH) |
*b | Component without harness connected
(to Headlight LED Unit Assembly LH) |
Remove the headlight assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>REMOVAL
Remove the headlight LED unit assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-6 (FANB) - D-3 | Always | Below 1 Ω |
| B-15 (FANP) - D-2 | Always | Below 1 Ω |
| B-14 (FANG) - D-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
| *a | Component without harness connected
(to Headlight LED Unit Assembly LH) |
Connect the B headlight ECU sub-assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-3 - D-1 | Low beam headlights on | 4.75 to 5.25 V |
| D-2 - D-1 | Low beam headlights on | 4.75 to 5.25 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
NG
| *a | Component without harness connected
(to Headlight ECU Sub-assembly RH) |
*b | Component without harness connected
(to Headlight LED Unit Assembly RH) |
Remove the headlight assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>REMOVAL
Remove the headlight LED unit assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-6 (FANB) - D-3 | Always | Below 1 Ω |
| B-15 (FANP) - D-2 | Always | Below 1 Ω |
| B-14 (FANG) - D-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
| *a | Component without harness connected
(to Headlight LED Unit Assembly RH) |
Connect the B headlight ECU sub-assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D-3 - D-1 | Low beam headlights on | 4.75 to 5.25 V |
| D-2 - D-1 | Low beam headlights on | 4.75 to 5.25 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
NG