The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P070513 | Transmission Range Sensor "A" Circuit Open | When the engine switch is on (IG) and battery voltage is 8 V or more, NSW, P, R, N and D input signals are all OFF simultaneously for 60 seconds or more (2-trip detection logic). | ·
Park/neutral position switch assembly ·
Open in park/neutral position switch assembly circuit ·
ECM |
Comes on | DTC stored | SAE Code:
P0705 |
| P070562 | Transmission Range Sensor "A" Signal Compare Failure | When the engine switch is on (IG) and battery voltage is 8 V or more, 2 or more of the following signals are ON simultaneously for 2 seconds or more (2-trip detection logic).
·
NSW, P or N input signal ·
R input signal ·
D input signal |
·
Park/neutral position switch assembly ·
Short in park/neutral position switch assembly circuit ·
ECM |
Comes on | DTC stored | SAE Code:
P0705 |
| Vehicle Condition | |||||
|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | ||
| Diagnostic Condition | Engine switch is on (IG) | ○ | ○ | ○ | ○ |
| Battery voltage is 8 V or more | ○ | ○ | ○ | ○ | |
| Malfunction Condition | NSW input signal is ON | ○ | ○ | - | - |
| P input signal is ON | - | - | ○ | ○ | |
| R input signal is ON | - | ○ | - | ○ | |
| N input signal is ON | - | - | - | - | |
| D input signal is ON | ○ | - | ○ | - | |
| Duration | 2 seconds or more | 2 seconds or more | 2 seconds or more | 2 seconds or more | |
| Detection Logic | 2-trip detection logic | 2-trip detection logic | 2-trip detection logic | 2-trip detection logic | |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 5 | Pattern 6 | Pattern 7 | ||
| Diagnostic Condition | Engine switch is on (IG) | ○ | ○ | ○ |
| Battery voltage is 8 V or more | ○ | ○ | ○ | |
| Malfunction Condition | NSW input signal is ON | - | - | - |
| P input signal is ON | - | - | - | |
| R input signal is ON | - | ○ | ○ | |
| N input signal is ON | ○ | ○ | - | |
| D input signal is ON | ○ | - | ○ | |
| Duration | 2 seconds or more | 2 seconds or more | 2 seconds or more | |
| Detection Logic | 2-trip detection logic | 2-trip detection logic | 2-trip detection logic | |
DTC P070562 is stored when any of the above detection patterns is met.
These DTCs indicate a problem with the park/neutral position switch assembly or the wire harness in the park/neutral position switch assembly circuit.
The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, N, R, D or S).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously and will then illuminate the MIL and store a DTC.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for 2 minutes or more.
Turn the engine switch on (IG) and turn the GTS on.
Wait with the shift lever in each position (P, R, N and D) for 60 seconds or more each with the engine switch on (IG).
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P070513 or P070562.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Inspect the fuses for circuits related to this system before performing the following procedure.
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
Disconnect the C55 park/neutral position switch assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C55-1 (RB) - Body ground | Engine switch on (IG) | 11 to 14 V |
| C55-1 (RB) - Body ground | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C55 park/neutral position switch assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C55-4 (B) - Body ground | Engine switch on (IG) | 11 to 14 V |
| C55-4 (B) - Body ground | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Park/Neutral Position Switch Assembly) |
Disconnect the C55 park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (B) - 9 (L) | Shift lever in P or N | Below 1 Ω |
| 1 (RB) - 3 (PL) | Shift lever in P | Below 1 Ω |
| 1 (RB) - 2 (RL) | Shift lever in R | Below 1 Ω |
| 1 (RB) - 8 (NL) | Shift lever in N | Below 1 Ω |
| 1 (RB) - 7 (DL) | Shift lever in D, S, "+" or "-" | Below 1 Ω |
| 4 (B) - 9 (L) | Shift lever not in P or N | 10 kΩ or higher |
| 1 (RB) - 3 (PL) | Shift lever not in P | 10 kΩ or higher |
| 1 (RB) - 2 (RL) | Shift lever not in R | 10 kΩ or higher |
| 1 (RB) - 8 (NL) | Shift lever not in N | 10 kΩ or higher |
| 1 (RB) - 7 (DL) | Shift lever not in D, S, "+" or "-" | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>COMPONENTS
Connect the C55 park/neutral position switch assembly connector.
Disconnect the C96 ECM connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C96-108 (P) - Body ground | ·
Engine switch on (IG) ·
Shift lever in P |
11 to 14 V |
| C96-107 (R) - Body ground | ·
Engine switch on (IG) ·
Shift lever in R |
11 to 14 V* |
| C96-140 (N) - Body ground | ·
Engine switch on (IG) ·
Shift lever in N |
11 to 14 V |
| C96-139 (D) - Body ground | ·
Engine switch on (IG) ·
Shift lever in D, S, "+" or "-" |
11 to 14 V |
| C96-108 (P) - Body ground | ·
Engine switch on (IG) ·
Shift lever not in P |
Below 1 V |
| C96-107 (R) - Body ground | ·
Engine switch on (IG) ·
Shift lever not in R |
Below 1 V |
| C96-140 (N) - Body ground | ·
Engine switch on (IG) ·
Shift lever not in N |
Below 1 V |
| C96-139 (D) - Body ground | ·
Engine switch on (IG) ·
Shift lever not in D, S, "+" or "-" |
Below 1 V |
*: The voltage will drop slightly due to the illumination of the back up lights.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION
Disconnect the C55 park/neutral position switch assembly connector.
Disconnect the C96 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C55-4 (B) - C96-106 (NSW) | Always | Below 1 Ω |
| C55-4 (B) or C96-106 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION