The headlight ECU sub-assembly operates using the power source voltage input from the IG terminal and ECUB terminal.
The IG terminal power source voltage is supplied by turning the IG1-NO. 1 relay to ON.
The headlight ECU sub-assembly receives ignition switch ON signals from the main body ECU (multiplex network body ECU) via CAN communication, compares the ignition switch ON signal and the power source voltage supply condition of the IG terminal and monitors the result.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B242E | Open in IG Circuit | Detection condition:
The ignition switch is ON. Malfunction status:
When the IG terminal power source voltage is 0 V (ignition switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received Malfunction duration:
10 seconds or more |
·
Headlight ECU sub-assembly LH ·
Harness or connector |
HL AutoLeveling |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| B242E | Open in IG Circuit | Detection condition:
The ignition switch is ON. Malfunction status:
When the IG terminal power source voltage is 0 V (ignition switch off), IG ON signals from the main body ECU (multiplex network body ECU) via CAN communication are continuously received Malfunction duration:
10 seconds or more |
·
Headlight ECU sub-assembly RH ·
Harness or connector |
HL AutoLeveling (Sub) |
Inspect the fuses for circuits related to this system before performing the following procedure.
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Wait 10 seconds or more.
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling or HL AutoLeveling (Sub) / Trouble Codes.
Check for DTCs.
DTC B242E is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (DTC output from headlight ECU sub-assembly LH) | B |
| NG (DTC output from headlight ECU sub-assembly RH) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
| *a | Front view of wire harness connector
(to Headlight ECU Sub-assembly LH) |
Disconnect the A83 headlight ECU sub-assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A83-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A83-12 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Headlight ECU Sub-assembly RH) |
Disconnect the A84 headlight ECU sub-assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A84-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A84-12 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG