Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2019.10
RM33A0E _51 Engine / Hybrid System _065332 2GR-FKS ENGINE CONTROL _0329835 SFI SYSTEM U

2GR-FKS ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A335752E70
2.344,0.375 2.792,0.677 0.448,0.302 5.771,0.417 6.219,0.719 0.448,0.302 2.438,0.417 2.896,0.615 0.458,0.198 10 false C96 5.875,0.458 6.333,0.656 0.458,0.198 10 false A23

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A23-1 (BATT) - C96-53 (E1) R - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A23-2 (+B) - C96-53 (E1) L - W-B Power source of ECM Engine switch on (IG) 11 to 14 V
A23-3 (+B2) - C96-53 (E1) L - W-B Power source of ECM Engine switch on (IG) 11 to 14 V
A23-4 (IGSW) - C96-53 (E1) B - W-B Engine switch signal Engine switch on (IG) 11 to 14 V
A23-7 (IREL) - C96-53 (E1) P - W-B INJ relay operation signal Engine stopped, engine switch on (IG) 0 to 1.5 V
A23-8 (+BM) - C96-53 (E1) G - W-B Power source of throttle actuator Always 11 to 14 V
A23-13 (CANH) - C96-53 (E1) B - W-B CAN communication line Engine stopped, engine switch on (IG) Pulse generation
(See waveform 1)
A23-14 (EC) - Body ground W-B - - Ground Always Below 1 Ω
A23-17 (S) - C96-53 (E1) GR - W-B S shift position switch signal Engine switch on (IG) and shift lever in S 11 to 14 V
Engine switch on (IG) and shift lever not in S Below 1 V
A23-18 (FPC) - C96-53 (E1) R - W-B Fuel pump control Engine stopped, engine switch on (IG) Below 1.5 V
A23-26 (CANL) - C96-53 (E1) W - W-B CAN communication line Engine stopped, engine switch on (IG) Pulse generation
(See waveform 2)
A23-27 (STP) - C96-53 (E1) SB - W-B Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
A23-30 (NEO) - C96-53 (E1) B - W-B Engine speed signal sent to other ECUs Idling with warm engine Pulse generation
(See waveform 3)
A23-39 (SPD) - C96-53 (E1) L - W-B Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(See waveform 4)
A23-42 (ST1-) - C96-53 (E1) LG - W-B Stop light switch assembly signal (opposite to STP terminal) Engine switch on (IG), brake pedal depressed 0 to 1.5 V
Engine switch on (IG), brake pedal released 7.5 to 14 V
A23-43 (STA) - C96-53 (E1) G - W-B Starter assembly signal Cranking 6.0 V or higher
A23-46 (MREL) - C96-53 (E1) W - W-B EFI MAIN relay operation signal Engine switch on (IG) 11 to 14 V
A23-47 (VPA) - A23-48 (EPA) G - L Accelerator pedal position sensor signal (for engine control) Engine switch on (IG), accelerator pedal fully released 0.5 to 1.1 V
Engine switch on (IG), accelerator pedal fully depressed 2.6 to 4.5 V
A23-49 (VCPA) - A23-48 (EPA) BE - L Power source of accelerator pedal position sensor (for VPA) Engine stopped, engine switch on (IG) 4.5 to 5.5 V
A23-50 (VPA2) - A23-51 (EPA2) GR - P Accelerator pedal position sensor signal Engine switch on (IG), accelerator pedal fully released 1.2 to 2.0 V
Engine switch on (IG), accelerator pedal fully depressed 3.4 to 4.75 V
A23-52 (VCP2) - A23-51 (EPA2) SB - P Power source of accelerator pedal position sensor (for VPA2) Engine stopped, engine switch on (IG) 4.5 to 5.5 V
A23-58 (KSW) - C96-53 (E1) R - W-B Key in vehicle signal Engine switch off → on (IG) 0 to 3.0 V
C96-2 (OE2+) - C96-3 (OE2-) R - W Cam timing oil control solenoid assembly (for exhaust camshaft of bank 2) operation signal Idling Pulse generation
(See waveform 5)
C96-4 (OE1+) - C96-5 (OE1-) G - R Cam timing oil control solenoid assembly (for exhaust camshaft of bank 1) operation signal Idling Pulse generation
(See waveform 5)
C96-9 (OC2+) - C96-8 (OC2-) B - L Cam timing oil control solenoid assembly (for intake camshaft of bank 2) operation signal Idling Pulse generation
(See waveform 6)
C96-16 (HT2B) - C96-53 (E1) L - W-B Heated oxygen sensor (bank 2 sensor 2) heater operation signal Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
C96-17 (HA2A) - C96-46 (E05) R - W-B Air fuel ratio sensor (bank 2 sensor 1) heater operation signal Idling Pulse generation
(See waveform 7)
Engine switch on (IG) 11 to 14 V
C96-18 (+BD2) - C96-53 (E1) L - W-B Power source of ECM (injector driver) Engine stopped, engine switch on (IG) 11 to 14 V
C96-19 (+BD1) - C96-53 (E1) L-R - W-B Power source of ECM (injector driver) Engine stopped, engine switch on (IG) 11 to 14 V
C96-20 (E02) - Body ground W-B - - Ground Always Below 1 Ω
C96-21 (E04) - Body ground W-B - - Ground Always Below 1 Ω
C96-23 (FP1+) - C96-22 (FP1-) Y - L Fuel pump assembly (for high pressure side) signal Idling with warm engine Pulse generation
C96-24 (#6D+) - C96-54 (#6D-) L - Y No. 6 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C96-25 (#3D+) - C96-26 (#3D-) V - P No. 3 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C96-27 (#5D+) - C96-57 (#5D-) L - Y No. 5 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C96-28 (#2D+) - C96-58 (#2D-) G - BR No. 2 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C96-29 (#4D+) - C96-59 (#4D-) V - P No. 4 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C96-30 (#1D+) - C96-60 (#1D-) B - W No. 1 fuel injector assembly (for direct injection) signal Idling with warm engine, Data List item "Injection Mode" displays "Direct" Pulse generation
C96-34 (IGT6) - C96-53 (E1) V - W-B No. 6 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C96-35 (IGT4) - C96-53 (E1) B - W-B No. 4 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C96-36 (IGT2) - C96-53 (E1) GR - W-B No. 2 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C96-38 (OC1+) - C96-68 (OC1-) W - G Cam timing oil control solenoid assembly (for intake camshaft of bank 1) operation signal Idling Pulse generation
(See waveform 6)
C96-39 (ACM) - C96-53 (E1) GR - W-B Vacuum switching valve (for active control engine mount system) operation signal Engine switch on (IG) 11 to 14 V
C96-40 (#60) - C96-51 (E01) G - W-B No. 6 fuel injector assembly (for port injection) signal Engine switch on (IG) 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C96-41 (#30) - C96-51 (E01) B - W-B No. 3 fuel injector assembly (for port injection) signal Engine switch on (IG) 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C96-42 (#50) - C96-51 (E01) R - W-B No. 5 fuel injector assembly (for port injection) signal Engine switch on (IG) 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C96-43 (#20) - C96-51 (E01) BE - W-B No. 2 fuel injector assembly (for port injection) signal Engine switch on (IG) 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C96-44 (#40) - C96-51 (E01) W - W-B No. 4 fuel injector assembly (for port injection) signal Engine switch on (IG) 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C96-45 (#10) - C96-51 (E01) GR - W-B No. 1 fuel injector assembly (for port injection) signal Engine switch on (IG) 0 to 5 V
Idling with warm engine, Data List item "Injection Mode" displaying "Port" Pulse generation
(See waveform 9)
C96-46 (E05) - Body ground W-B - - Ground Always Below 1 Ω
C96-47 (M-) - C96-49 (ME01) P - W-B Throttle actuator operation signal (negative signal) Idling with warm engine Pulse generation
(See waveform 10)
C96-48 (M+) - C96-49 (ME01) V - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 11)
C96-49 (ME01) - Body ground W-B - - Ground Always Below 1 Ω
C96-50 (HT1B) - C96-53 (E1) L - W-B Heated oxygen sensor (bank 1 sensor 2) heater operation signal Idling Below 3.0 V
Engine switch on (IG) 11 to 14 V
C96-51 (E01) - Body ground W-B - - Ground Always Below 1 Ω
C96-52 (HA1A) - C96-21 (E04) B - W-B Air fuel ratio sensor (bank 1 sensor 1) heater operation signal Idling Pulse generation
(See waveform 7)
Engine switch on (IG) 11 to 14 V
C96-53 (E1) - Body ground W-B - - Ground Always Below 1 Ω
C96-55 (E1D2) - Body ground B - - Ground Always Below 1 Ω
C96-56 (E1D1) - Body ground W - - Ground Always Below 1 Ω
C96-64 (PTCR) - C96-53 (E1) L - W-B Thermostat heater operation signal Engine switch on (IG) 11 to 14 V
C96-65 (PRG) - C96-53 (E1) R - W-B Purge VSV operation signal Engine switch on (IG) 11 to 14 V
Idling Pulse generation
(See waveform 12)
C96-66 (ACIS) - C96-53 (E1) L - W-B No. 1 vacuum switching valve (for intake air control valve sub-assembly) operation signal Engine switch on (IG) 11 to 14 V
C96-69 (IGT5) - C96-53 (E1) R - W-B No. 5 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C96-70 (IGT3) - C96-53 (E1) L - W-B No. 3 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C96-71 (IGT1) - C96-53 (E1) GR - W-B No. 1 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 8)
C96-82 (KNK1) - C96-81 (EKNK) B - W Knock control sensor (bank 1) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 13)
C96-87 (PR) - C96-133 (ETHW) P - BR Fuel pressure sensor (for high pressure side) signal Idling with warm engine 0.5 to 4.5 V
C96-89 (VTA2) - C96-120 (ETA) LG - B Throttle position sensor signal (for sensor malfunction detection) Engine switch on (IG), accelerator pedal fully released 2.1 to 3.1 V
Accelerator pedal fully depressed (engine running) 4.6 to 5.0 V
C96-90 (VC) - C96-53 (E1) W - W-B Power source for sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C96-91 (OX2B) - C96-92 (EX2B) G - W Heated oxygen sensor (bank 2 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 14)
C96-93 (OX1B) - C96-94 (EX1B) R - G Heated oxygen sensor (bank 1 sensor 2) signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 14)
C96-96 (VCNE) - C96-53 (E1) R - W-B Power source of crankshaft position sensor (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C96-98 (VCV2) - C96-97 (VV2-) R - B Power source of VVT sensor (bank 2) (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C96-99 (VCV1) - C96-100 (VV1-) W - R Power source of VVT sensor (bank 1) (specific voltage) Engine switch on (IG) 4.5 to 5.5 V
C96-101 (THW) - C96-133 (ETHW) B - BR Engine coolant temperature sensor Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V
C96-102 (THA) - C96-115 (E2G) L - LG Intake air temperature sensor Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C96-106 (NSW) - C96-53 (E1) R - W-B Park/Neutral position switch assembly signal Engine switch on (IG), shift lever not in P or N 11 to 14 V
Engine switch on (IG), shift lever in P or N Below 1 V
C96-107 (R) - C96-53 (E1) W - W-B R shift position switch signal Engine switch on (IG), shift lever in R 11 to 14 V
Engine switch on (IG), shift lever not in R Below 1 V
C96-108 (P) - C96-53 (E1) B - W-B P shift position switch signal Engine switch on (IG), shift lever in P 11 to 14 V
Engine switch on (IG), shift lever not in P Below 1 V
C96-114 (KNK2) - C96-113 (EKN2) R - G Knock control sensor (bank 2) signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 13)
C96-116 (VG) - C96-115 (E2G) R - LG Mass air flow meter sub-assembly signal Engine switch on (IG) Pulse generation
(See waveform 15)
C96-121 (VCTA) - C96-120 (ETA) R - B Power source of throttle position sensor (specific voltage) Engine stopped, engine switch on (IG) 4.5 to 5.5 V
C96-122 (VTA1) - C96-120 (ETA) G - B Throttle position sensor signal (for engine control) Engine switch on (IG), accelerator pedal fully released 0.6 to 1.1 V
Accelerator pedal fully depressed (engine running) 3.2 to 4.8 V
C96-123 (A2A+) - C96-53 (E1) P - W-B Air fuel ratio sensor (bank 2 sensor 1) signal Engine switch on (IG) 3.3 V*
C96-124 (A2A-) - C96-53 (E1) L - W-B Air fuel ratio sensor (bank 2 sensor 1) signal Engine switch on (IG) 2.9 V*
C96-125 (A1A+) - C96-53 (E1) Y - W-B Air fuel ratio sensor (bank 1 sensor 1) signal Engine switch on (IG) 3.3 V*
C96-126 (A1A-) - C96-53 (E1) BR - W-B Air fuel ratio sensor (bank 1 sensor 1) signal Engine switch on (IG) 2.9 V*
C96-127 (GE01) - Body ground BR - - Shielded earth (ground) circuit of throttle actuator Always Below 1 Ω
C96-128 (NE+) - C96-95 (NE-) L - B Crankshaft position sensor Idling with warm engine Pulse generation
(See waveform 16)
C96-129 (VV2+) - C96-97 (VV2-) G - B VVT sensor (for intake camshaft of bank 2) signal Idling Pulse generation
(See waveform 17)
C96-130 (EV2+) - C96-97 (VV2-) GR - B VVT sensor (for exhaust camshaft of bank 2) signal Idling Pulse generation
(See waveform 18)
C96-131 (EV1+) - C96-100 (VV1-) B - R VVT sensor (for exhaust camshaft of bank 1) signal Idling Pulse generation
(See waveform 18)
C96-132 (VV1+) - C96-100 (VV1-) G - R VVT sensor (for intake camshaft of bank 1) signal Idling Pulse generation
(See waveform 17)
C96-134 (PFL) - C96-133 (ETHW) R - BR Fuel pressure sensor (for low pressure side) signal Idling with warm engine 0.75 to 4.5 V
C96-136 (RFC) - C96-53 (E1) LG - W-B Cooling fan control signal Engine switch on (IG), A/C switch on (max cool) Pulse generation
(See waveform 19)
C96-139 (D) - C96-53 (E1) R - W-B D shift position switch signal Engine switch on (IG) and shift lever in D or S 11 to 14 V
Engine switch on (IG) and shift lever not in D or S Below 1 V
C96-140 (N) - C96-53 (E1) LG - W-B N shift position switch signal Engine switch on (IG), shift lever in N 11 to 14 V
Engine switch on (IG), shift lever not in N Below 1 V

*: The ECM terminal voltage is constant regardless of the voltage output from the sensor.

WAVEFORM 1


A283576E01
2.75,0.292 3.354,0.583 0.604,0.292 10 1 V/DIV. 3.01,1.396 3.344,1.708 0.333,0.313 10 GND 1.604,1.896 2.479,2.125 0.875,0.229 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A283577E01
2.76,0.271 3.375,0.531 0.615,0.26 10 1 V/DIV. 3.01,1.365 3.375,1.604 0.365,0.24 10 GND 1.625,1.865 2.583,2.052 0.958,0.188 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, engine switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A287796E02
2.594,1.656 3.052,1.854 0.458,0.198 10 GND 0.063,0.063 0.781,0.292 0.719,0.229 10 1 V/DIV. 1.167,1.927 2,2.135 0.833,0.208 10 2 ms./DIV.

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 1 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


A283573E11
2.677,0.125 3.354,0.385 0.677,0.26 10 false 2 V/DIV. 2.833,1.229 3.25,1.531 0.417,0.302 10 false GND 1.156,1.99 2.219,2.167 1.063,0.177 10 false 20 ms./DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 5


A283575E01
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Cam Timing Oil Control Solenoid Assembly (for Exhaust Camshaft) Signal
ECM Terminal Name Between OE1+ and OE1-
Between OE2+ and OE2-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 6


A283575E01
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Cam Timing Oil Control Solenoid Assembly (for Intake Camshaft) Signal
ECM Terminal Name Between OC1+ and OC1-
Between OC2+ and OC2-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 7


A205412E04
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Between HA2A and E05
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling


WAVEFORM 8


A408366E03
0.063,0.063 0.635,0.26 0.573,0.198 10 false 2 V/DIV. 1.354,1.938 2.208,2.125 0.854,0.188 10 false 20 ms./DIV. 2.938,0.979 3.292,1.229 0.354,0.25 10 false GND

Ignition Coil Assembly Signal (IGT and IGF Signal)
ECM Terminal Name Between IGT (1 to 6) and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


WAVEFORM 9


A287799E11
0.656,1.583 1.115,1.781 0.458,0.198 10 false GND 0.396,0.115 1.063,0.344 0.667,0.229 10 false 20 V/DIV. 1.833,1.896 2.646,2.083 0.813,0.188 10 false 20 ms./DIV.

No. 1 (to No. 6) Fuel Injector Assembly (for Port Injection) Signal
ECM Terminal Name Between #10 (to #60) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, Data List item "Injection Mode" displaying "Port"

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

When the port injection injectors are operating, Port is displayed for Injection Way of the Data List.




WAVEFORM 10


A245848E22
2.854,1 3.323,1.354 0.469,0.354 10 GND 2.625,0.313 3.323,0.594 0.698,0.281 10 5 V/DIV. 0.479,0.625 0.844,0.875 0.365,0.25 10 M- 1.417,1.802 2.573,2.052 1.156,0.25 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 11


A208000E20
2.854,0.99 3.313,1.302 0.458,0.313 10 GND 2.635,0.26 3.313,0.552 0.677,0.292 10 5 V/DIV. 0.521,0.656 0.99,0.948 0.469,0.292 10 M+ 1.396,1.802 2.281,2.021 0.885,0.219 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 12


A218020E05
2.677,0.208 3.344,0.51 0.667,0.302 10 10 V/DIV. 2.802,0.938 3.292,1.26 0.49,0.323 10 GND 1.26,1.771 2.25,2.021 0.99,0.25 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 13


A283572E01
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Between KNK2 and EKN2
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed will differ slightly depending on the vehicle.




WAVEFORM 14


A283571E01
0.51,0.219 1.292,0.521 0.781,0.302 10 0.2 V/DIV. 0.573,1.479 1.021,1.76 0.448,0.281 10 GND 1.802,1.875 2.771,2.115 0.969,0.24 10 200 ms./DIV.

Heated Oxygen Sensor Signal
ECM Terminal Name Between OX1B and EX1B
Between OX2B and EX2B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

Data List, item "O2 Sensor Voltage B1S2" and "O2 Sensor Voltage B2S2" shows the ECM values from the heated oxygen sensor.



WAVEFORM 15


A337204E05
0.115,1.417 0.469,1.615 0.354,0.198 10 false GND 1.406,1.958 2.188,2.156 0.781,0.198 10 false 100 μs./DIV. 2.813,0.167 3.406,0.375 0.594,0.208 10 false 1 V/DIV.

Mass Air Flow Meter Sub-assembly Signal
ECM Terminal Name Between VG and E2G
Tester Range 1 V/DIV., 100 μs./DIV.
Condition Engine switch on (IG)


WAVEFORM 16


A200774E03
2.969,1.177 3.396,1.438 0.427,0.26 10 GND 0.083,0.073 0.698,0.292 0.615,0.219 10 2 V/DIV. 1.229,1.875 2.25,2.104 1.021,0.229 10 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 17


A356009E02
0.094,1.323 0.479,1.542 0.385,0.219 10 false CH1 0.135,2.063 0.469,2.271 0.333,0.208 10 false CH2 2.813,1.479 3.271,1.677 0.458,0.198 10 false GND 2.802,2.208 3.26,2.406 0.458,0.198 10 false GND 2.677,0.771 3.302,1 0.625,0.229 10 false 5 V/DIV. 1.25,2.552 2.938,2.75 1.688,0.198 10 false 20 ms./DIV.

VVT Sensor (for Intake Camshaft) Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 18


A356008E02
0.094,1.365 0.438,1.573 0.344,0.208 10 false CH1 0.115,2.094 0.458,2.302 0.344,0.208 10 false CH2 1.26,2.542 2.167,2.802 0.906,0.26 10 false 20 ms./DIV. 2.802,1.469 3.26,1.667 0.458,0.198 10 false GND 2.802,2.208 3.26,2.406 0.458,0.198 10 false GND 2.698,0.771 3.302,1.021 0.604,0.25 10 false 5 V/DIV.

VVT Sensor (for Exhaust Camshaft) Signal
ECM Terminal Name CH1: Between EV1+ and VV1-
CH2: Between EV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 19


A282867E08
2.76,1.563 3.115,1.792 0.354,0.229 10 false GND 0.063,0.063 0.708,0.344 0.646,0.281 10 false 1 V/DIV. 1.344,1.854 2.208,2.083 0.865,0.229 10 false 20 ms./DIV.

Cooling Fan Control Signal
ECM Terminal Name Between RFC and E1
Tester Range 1 V/DIV., 20 ms./DIV.
Condition Engine switch on (IG), A/C switch on (max cool)

HINT:

The duty ratio varies depending on the engine coolant temperature.