Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT › 2019.10–2021.02
RM33A0E _53 Suspension _065360 ALIGNMENT / HANDLING DIAGNOSIS _0318999 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the front wheel alignment procedure are shown below.

Necessary Procedures After Procedure Performed
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 1. PRECAUTION

As the standard wheel alignment values differ depending on the suspension type, refer to the following table to confirm the suspension type for each model.

MODEL CODE SUSPENSION TYPE
ASV70R-AETDKQ NORMAL
ASV70R-AETNKQ NORMAL
ASV70R-AETVKQ SPORT
GSV70R-AEZNBQ NORMAL
GSV70R-AEZVBQ SPORT
AXVA70L-AEZDBV NORMAL
AXVA70L-AEZNBV NORMAL
AXVA70L-AEZSBV SPORT
ASV70L-AETDKV NORMAL
ASV70L-AETNKV NORMAL
ASV70L-AETSKV SPORT
GSV70L-AEZGBV NORMAL
GSV70L-AEZSBV SPORT
ASV70L-AETNKW NORMAL
AXVA70L-AEZNBW NORMAL
AXVA70L-AEZSBW NORMAL
GSV70L-AEZGBW NORMAL
ASV70R-AETNKW NORMAL
ASV71L-RETNHX NORMAL
ASV70L-RETNKX NORMAL
GSV70L-REZGBX NORMAL
ASV70L-AETDKR NORMAL

Hide 3.MEASURE VEHICLE HEIGHT

NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C370166N01
0.844,1.125 1,1.323 0.156,0.198 10 false A 2.406,1.198 2.563,1.396 0.156,0.198 10 false B 0.813,3.99 0.969,4.188 0.156,0.198 10 false C 2.375,4.031 2.531,4.229 0.156,0.198 10 false D

Measure the vehicle height.

Measurement Points:

A: Ground clearance of front wheel center


B: Ground clearance of center of bolt head of front lower No. 2 suspension arm bushing (rear bolt of front lower No. 1 suspension arm sub-assembly).


C: Ground clearance of rear wheel center


D: Ground clearance of center of bolt head of rear No. 2 suspension arm assembly and rear suspension member sub-assembly.


Vehicle Height (Unloaded Vehicle):
Engine SUSPENSION TYPE Front A - B Rear C - D

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL 150 mm (5.91 in.)
138 mm (5.43 in.)*
49 mm (1.93 in.)
38 mm (1.50 in.)*
SPORT 150 mm (5.91 in.) 46 mm (1.81 in.)
2GR-FKS NORMAL 155 mm (6.10 in.)
140 mm (5.51 in.)*
53 mm (2.09 in.)
41 mm (1.61 in.)*
SPORT 152 mm (5.98 in.) 49 mm (1.93 in.)



Hide 4.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:

Inspect while the vehicle is unloaded.


a.
C132440C16
2.396,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.458 false 2.76,0.729 2.99,0.906 0.229,0.177 10 false *b 0.448,0.604 0.688,0.781 0.24,0.177 10 false *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


b.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
Engine SUSPENSION TYPE Camber Inclination Right-left Difference

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL -0°30' +/- 0°45' (-0.50° +/- 0.75°)
-0°20' +/- 0°45' (-0.33° +/- 0.75°)*
0°45' (0.75°) or less
SPORT -0°30' +/- 0°45' (-0.50° +/- 0.75°)
2GR-FKS NORMAL -0°35' +/- 0°45' (-0.58° +/- 0.75°)
-0°25' +/- 0°45' (-0.42° +/- 0.75°)*
SPORT -0°30' +/- 0°45' (-0.50° +/- 0.75°)


Caster (Unloaded Vehicle):
Engine SUSPENSION TYPE Caster Inclination Right-left Difference

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL 5°20' +/- 0°45' (5.33° +/- 0.75°)
5°15' +/- 0°45' (5.25° +/- 0.75°)*
0°45' (0.75°) or less
SPORT 5°20' +/- 0°45' (5.33° +/- 0.75°)
2GR-FKS NORMAL 5°20' +/- 0°45' (5.33° +/- 0.75°)
5°15' +/- 0°45' (5.25° +/- 0.75°)*
SPORT 5°20' +/- 0°45' (5.33° +/- 0.75°)


Steering Axis Inclination (Unloaded Vehicle):
Engine SUSPENSION TYPE Steering Axis Inclination Reference

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL 12°55' (12.92°)
12°35' (12.58°)*
SPORT 12°55' (12.92°)
2GR-FKS NORMAL 13°00' (13.00°)
12°40' (12.67°)*
SPORT 13°00' (13.00°)



Hide 5.ADJUST CAMBER

NOTICE:

Inspect toe-in after the camber has been adjusted.


a.

Remove the front wheel.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>REMOVAL


b.
C370167

Remove the 2 nuts on the lower side of the front shock absorber assembly.

NOTICE:

Keep the bolts inserted.



c.

Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber assembly.

HINT:
·

Reinstall each bolt after removing it and confirming steering knuckle movement.

·

If the steering knuckle does not move freely in the front shock absorber assembly, clean the contact surfaces of the front shock absorber assembly and the steering knuckle.




d.

Temporarily install the 2 nuts. (Step A)


e.
C199624N01
1.01,0.125 1.167,0.323 0.156,0.198 10 - 1.875,0.052 2.031,0.25 0.156,0.198 10 +

Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)


f.
C370167

Tighten the 2 nuts.

Torque:
290 N*m (2957 kgf*cm, 214 ft.*lbf)

NOTICE:

Keep the bolts from rotating when tightening the nuts.



g.

Install the front wheel.

Click hereGeneral>MAINTENANCE>TIRE AND WHEEL>INSTALLATION


h.

Bounce the vehicle up and down at the corners to stabilize the suspension.


i.

Check the camber.

Camber (Unloaded Vehicle):
Engine SUSPENSION TYPE Camber Inclination Right-left Difference

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL -0°30' +/- 0°45' (-0.50° +/- 0.75°)
-0°20' +/- 0°45' (-0.33° +/- 0.75°)*
0°45' (0.75°) or less
SPORT -0°30' +/- 0°45' (-0.50° +/- 0.75°)
2GR-FKS NORMAL -0°35' +/- 0°45' (-0.58° +/- 0.75°)
-0°25' +/- 0°45' (-0.42° +/- 0.75°)*
SPORT -0°30' +/- 0°45' (-0.50° +/- 0.75°)


i.
C241271N01
0.354,1.125 0.563,1.125 false 0.344,1.417 0.521,1.417 false 0.208,1.021 0.365,1.219 0.156,0.198 10 false 1 0.208,1.344 0.365,1.542 0.156,0.198 10 false 2

If the measured value is not within the specification, calculate the required adjustment amount using the formula below.

Camber adjustment amount = center of the specified range - measured value

Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.

HINT:

Try to adjust the camber to the center of the specified values.


To move the axle hub toward (+) in step B To move the axle hub toward (-) in step B
Refer to table (1) (To move the axle hub toward the positive side) Refer to table (2) (To move the axle hub toward the negative side)

The vehicle body and suspension may be damaged if the camber cannot be correctly adjusted according to the table above.

NOTICE:

Replace the nut with a new one when replacing the bolt.



ii.

Table (1) (To move the axle hub toward the positive side)

C212217C01
2.052,0.531 2.188,0.74 0.135,0.208 10 1 2.052,1.146 2.188,1.354 0.135,0.208 10 2 2.521,0.792 2.75,0.99 0.229,0.198 10 *c 3.219,1.406 3.448,1.594 0.229,0.188 10 *d 5.979,0.792 6.198,0.99 0.219,0.198 10 *e 5.271,0.792 5.521,0.99 0.25,0.198 10 *d 4.604,1.406 4.781,1.583 0.177,0.177 10 *f 3.917,1.406 4.125,1.615 0.208,0.208 10 *e 4.396,6.375 4.583,6.552 0.188,0.177 10 *f 5.969,1.396 6.177,1.552 0.208,0.156 10 *f 5.271,1.406 5.469,1.583 0.198,0.177 10 *f 6.656,1.396 6.833,1.552 0.177,0.156 10 *f 6.646,0.792 6.854,0.969 0.208,0.177 10 *f 2.542,2.99 2.719,3.219 0.177,0.229 10 A 2.542,4.188 2.771,4.406 0.229,0.219 10 F 2.542,3.469 2.771,3.688 0.229,0.219 10 C 2.542,3.938 2.74,4.156 0.198,0.219 10 E 2.542,3.24 2.729,3.448 0.188,0.208 10 B 2.542,3.708 2.729,3.927 0.188,0.219 10 D 3.927,3.01 4.177,3.24 0.25,0.229 10 C 5.271,3 5.51,3.229 0.24,0.229 10 E 3.229,3.01 3.406,3.219 0.177,0.208 10 B 4.604,3 4.792,3.24 0.188,0.24 10 D 3.229,2.76 3.448,2.99 0.219,0.229 10 G 3.229,3.24 3.406,3.448 0.177,0.208 10 C 3.229,3.708 3.448,3.938 0.219,0.229 10 E 3.229,3.469 3.427,3.698 0.198,0.229 10 D 3.229,3.938 3.427,4.167 0.198,0.229 10 F 3.927,2.51 4.115,2.74 0.188,0.229 10 G 3.927,2.76 4.135,2.969 0.208,0.208 10 A 3.927,3.708 4.115,3.938 0.188,0.229 10 F 3.917,3.469 4.083,3.688 0.167,0.219 10 E 3.927,3.24 4.135,3.458 0.208,0.219 10 D 4.604,2.281 4.802,2.531 0.198,0.25 10 G 6.656,1.563 6.833,1.823 0.177,0.26 10 G 5.979,1.813 6.26,2.063 0.281,0.25 10 G 5.271,2.031 5.458,2.281 0.188,0.25 10 G 6.656,1.813 6.813,2.042 0.156,0.229 10 A 6.656,2.281 6.844,2.531 0.188,0.25 10 C 6.656,2.76 6.885,3.01 0.229,0.25 10 E 6.656,2.031 6.833,2.26 0.177,0.229 10 B 6.656,2.51 6.875,2.781 0.219,0.271 10 D 5.979,2.031 6.177,2.292 0.198,0.26 10 A 5.979,2.51 6.188,2.75 0.208,0.24 10 C 5.979,2.281 6.26,2.531 0.281,0.25 10 B 5.979,2.76 6.167,2.99 0.188,0.229 10 D 5.979,3 6.115,3.208 0.135,0.208 10 F 5.271,3.24 5.49,3.448 0.219,0.208 10 F 5.271,2.281 5.406,2.51 0.135,0.229 10 A 5.271,2.76 5.448,2.969 0.177,0.208 10 C 5.271,2.51 5.438,2.74 0.167,0.229 10 B 4.604,2.51 4.781,2.76 0.177,0.25 10 A 4.604,2.76 4.781,2.969 0.177,0.208 10 B 4.604,3.24 4.813,3.458 0.208,0.219 10 E 4.604,3.469 4.813,3.698 0.208,0.229 10 F 1.625,5.073 1.76,5.281 0.135,0.208 10 A 5.094,5.073 5.229,5.281 0.135,0.208 10 F 3.052,5.073 3.188,5.281 0.135,0.208 10 C 4.406,5.073 4.542,5.281 0.135,0.208 10 E 2.344,5.073 2.479,5.281 0.135,0.208 10 B 3.729,5.073 3.865,5.281 0.135,0.208 10 D 5.802,5.073 5.938,5.281 0.135,0.208 10 G 1.073,5.5 1.208,5.708 0.135,0.208 10 1 1.104,6.135 1.24,6.344 0.135,0.208 10 2 3.042,6.375 3.229,6.531 0.188,0.156 10 *f 3.719,6.375 3.958,6.542 0.24,0.167 10 *f 5.083,6.375 5.292,6.573 0.208,0.198 10 *f 5.094,5.75 5.292,5.917 0.198,0.167 10 *f 4.385,5.75 4.604,5.917 0.219,0.167 10 *e 2.333,6.375 2.542,6.542 0.208,0.167 10 *e 1.625,6.375 1.854,6.552 0.229,0.177 10 *d 3.719,5.75 3.927,5.938 0.208,0.188 10 *d 3.01,5.75 3.208,5.938 0.198,0.188 10 *c 1.625,5.75 1.844,5.948 0.219,0.198 10 *c 2.333,5.75 2.521,5.906 0.188,0.156 10 *c 5.802,6.365 6.021,6.563 0.219,0.198 10 *c 5.76,5.76 5.969,5.948 0.208,0.188 10 *c 0.177,1.563 2.198,1.75 2.021,0.188 10 -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 -0°15' to 0° (-0.25° to 0°) 0.208,2.51 2.156,2.729 1.948,0.219 10 -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 1°15' to 1°30' (1.25° to 1.5°) 2.542,1.406 2.76,1.604 0.219,0.198 10 *c 3.219,0.792 3.448,0.969 0.229,0.177 10 *c 3.917,0.792 4.135,1.01 0.219,0.219 10 *c 4.604,0.792 4.823,1.01 0.219,0.219 10 *c 5.979,3 6.24,3.24 0.26,0.24 10 F 1.156,0.625 1.333,0.792 0.177,0.167 10 *a 0.625,1.115 0.802,1.281 0.177,0.167 10 *b 0.875,4.792 1.198,5.021 0.323,0.229 12 *B 0.063,0.135 0.333,0.333 0.271,0.198 12 *A
*A Table (1) (To move the axle hub toward the positive side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c Standard Bolt *d 90105-17013
*e 90105-17014 *f 90105-17015



iii.

Table (2) (To move the axle hub toward the negative side)

C212218C01
2.052,0.531 2.188,0.74 0.135,0.208 10 1 2.052,1.146 2.188,1.354 0.135,0.208 10 2 1.635,5.052 1.771,5.26 0.135,0.208 10 A 5.094,5.052 5.229,5.26 0.135,0.208 10 F 3.052,5.052 3.188,5.26 0.135,0.208 10 C 4.406,5.052 4.542,5.26 0.135,0.208 10 E 2.344,5.052 2.479,5.26 0.135,0.208 10 B 3.729,5.052 3.865,5.26 0.135,0.208 10 D 5.802,5.052 5.938,5.26 0.135,0.208 10 G 1.073,5.5 1.208,5.708 0.135,0.208 10 1 1.104,6.135 1.24,6.344 0.135,0.208 10 2 0.177,1.563 2.198,1.75 2.021,0.188 10 -1°30' to -1°15' (-1.50° to -1.25°) 0.406,2.76 1.969,2.948 1.563,0.188 10 -0°15' to 0° (-0.25° to 0°) 0.208,2.521 2.156,2.74 1.948,0.219 10 -0°30' to -0°15' (-0.5° to -0.25°) 0.208,2.281 2.156,2.479 1.948,0.198 10 -0°45' to -0°30' (-0.75° to -0.5°) 0.271,2.031 2.104,2.208 1.833,0.177 10 -1°00' to -0°45' (-1° to -0.75°) 0.26,1.813 2.094,2.021 1.833,0.208 10 -1°15' to -1°00' (-1.25° to -1°) 0.354,3.938 2.01,4.115 1.656,0.177 10 1°00' to 1°15' (1° to 1.25°) 0.354,3.708 2,3.906 1.646,0.198 10 0°45' to 1°00' (0.75° to 1°) 0.302,3.469 2.073,3.646 1.771,0.177 10 0°30' to 0°45' (0.5° to 0.75°) 0.302,3.24 2.073,3.417 1.771,0.177 10 0°15' to 0°30' (0.25° to 0.5°) 0.448,3 1.917,3.198 1.469,0.198 10 0° to 0°15' (0° to 0.25°) 0.302,4.188 2.073,4.365 1.771,0.177 10 1°15' to 1°30' (1.25° to 1.5°) 1.156,0.625 1.333,0.792 0.177,0.167 10 *a 0.625,1.115 0.802,1.281 0.177,0.167 10 *b 0.875,4.792 1.167,5.021 0.292,0.229 12 *B 0.063,0.135 0.417,0.354 0.354,0.219 12 *A 5.292,2.76 5.427,2.969 0.135,0.208 10 E 5.292,3.708 5.427,3.917 0.135,0.208 10 G 5.292,2.521 5.427,2.729 0.135,0.208 10 F 5.292,3.469 5.427,3.677 0.135,0.208 10 A 5.292,3 5.427,3.208 0.135,0.208 10 C 5.292,3.24 5.427,3.448 0.135,0.208 10 B 2.542,2.76 2.677,2.969 0.135,0.208 10 A 2.542,1.563 2.677,1.771 0.135,0.208 10 F 2.542,2.281 2.677,2.49 0.135,0.208 10 C 2.542,1.813 2.677,2.021 0.135,0.208 10 E 2.542,2.521 2.677,2.729 0.135,0.208 10 B 2.542,2.031 2.677,2.24 0.135,0.208 10 D 3.229,2.76 3.365,2.969 0.135,0.208 10 B 3.229,3 3.365,3.208 0.135,0.208 10 G 3.229,2.521 3.365,2.729 0.135,0.208 10 C 3.229,2.031 3.365,2.24 0.135,0.208 10 E 3.229,2.281 3.365,2.49 0.135,0.208 10 D 3.229,1.813 3.375,2.021 0.146,0.208 10 F 3.927,2.76 4.063,2.969 0.135,0.208 10 C 3.927,3.24 4.063,3.448 0.135,0.208 10 G 3.927,3 4.063,3.208 0.135,0.208 10 A 3.927,2.031 4.063,2.24 0.135,0.208 10 F 3.927,2.281 4.063,2.49 0.135,0.208 10 E 3.927,2.521 4.063,2.729 0.135,0.208 10 D 4.604,2.76 4.74,2.969 0.135,0.208 10 D 4.604,3.469 4.74,3.677 0.135,0.208 10 G 4.604,3.24 4.74,3.448 0.135,0.208 10 A 4.604,3 4.74,3.208 0.135,0.208 10 B 4.604,2.521 4.74,2.729 0.135,0.208 10 E 4.604,2.281 4.74,2.49 0.135,0.208 10 F 5.99,3.938 6.125,4.146 0.135,0.208 10 G 5.99,3.708 6.125,3.917 0.135,0.208 10 A 5.99,3.24 6.125,3.448 0.135,0.208 10 C 5.99,3.469 6.125,3.677 0.135,0.208 10 B 5.99,3 6.125,3.208 0.135,0.208 10 D 5.99,2.76 6.125,2.969 0.135,0.208 10 F 6.688,4.188 6.823,4.396 0.135,0.208 10 G 6.688,3.938 6.823,4.146 0.135,0.208 10 A 6.688,3.469 6.823,3.677 0.135,0.208 10 C 6.688,3 6.823,3.208 0.135,0.208 10 E 6.688,3.708 6.823,3.917 0.135,0.208 10 B 6.688,3.24 6.823,3.448 0.135,0.208 10 D 2.51,0.792 2.729,0.969 0.219,0.177 10 *c 3.219,1.396 3.406,1.573 0.188,0.177 10 *d 5.969,0.781 6.115,0.938 0.146,0.156 10 *e 5.271,0.792 5.469,0.979 0.198,0.188 10 *d 4.604,1.396 4.781,1.573 0.177,0.177 10 *f 3.906,1.396 4.083,1.573 0.177,0.177 10 *e 5.979,1.396 6.188,1.552 0.208,0.156 10 *f 5.281,1.396 5.479,1.573 0.198,0.177 10 *f 6.656,1.396 6.833,1.552 0.177,0.156 10 *f 6.656,0.792 6.823,0.958 0.167,0.167 10 *f 2.51,1.396 2.688,1.573 0.177,0.177 10 *c 3.219,0.792 3.396,0.948 0.177,0.156 10 *c 3.927,0.792 4.115,0.979 0.188,0.188 10 *c 4.604,0.792 4.781,0.958 0.177,0.167 10 *c 4.385,6.375 4.531,6.531 0.146,0.156 10 *f 3.01,6.375 3.198,6.531 0.188,0.156 10 *f 3.708,6.375 3.948,6.542 0.24,0.167 10 *f 5.094,6.375 5.302,6.573 0.208,0.198 10 *f 5.083,5.75 5.271,5.906 0.188,0.156 10 *f 4.375,5.75 4.573,5.906 0.198,0.156 10 *e 2.313,6.375 2.521,6.542 0.208,0.167 10 *e 1.625,6.375 1.771,6.531 0.146,0.156 10 *d 3.688,5.75 3.875,5.938 0.188,0.188 10 *d 3.01,5.75 3.208,5.938 0.198,0.188 10 *c 1.625,5.74 1.802,5.927 0.177,0.188 10 *c 2.323,5.75 2.5,5.906 0.177,0.156 10 *c 5.781,6.375 5.969,6.542 0.188,0.167 10 *c 5.771,5.75 5.979,5.938 0.208,0.188 10 *c
*A Table (2) (To move the axle hub toward the negative side) *B Selected Bolt Combination
*a Installed Bolt *b Adjusting Value
*c Standard Bolt *d 90105-17013
*e 90105-17014 *f 90105-17015




j.

If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step A, replace the existing bolts with the selected bolts.

HINT:

Replace one bolt at a time when replacing both bolts.



Hide 6.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


d.
C188968C01
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 *a 2.427,1.698 2.604,1.854 0.177,0.156 10 *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


e.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step C again.



f.
C188969C01
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle):
Engine SUSPENSION TYPE Specified Condition

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)
C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)*
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)
B - A: 1.8 +/- 2.0 mm (0.0709 +/- 0.0787 in.)*
SPORT C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)
2GR-FKS NORMAL C + D: 0°06' +/- 0°10' (0.09° +/- 0.17°)
C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)*
B - A: 1.1 +/- 2.0 mm (0.0433 +/- 0.0787 in.)
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)*
SPORT C + D: 0°07' +/- 0°10' (0.12° +/- 0.17°)
B - A: 1.4 +/- 2.0 mm (0.0551 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the steering rack ends.


Hide 7.ADJUST TOE-IN

a.
C370168C01
1.625,1.604 1.865,1.792 0.24,0.188 10 true *a
*a Thread Length


Make sure that the thread length of the right and left steering rack ends are approximately the same.

Standard Difference:

1.5 mm (0.0591 in.) or less



b.

Separate the steering rack boot clips from the steering rack boot.


c.
C370169

Loosen the tie rod assembly lock nuts.


d.

Adjust the steering rack ends if the difference in thread length between the right and left steering rack ends is not within the specified range.

i.

If the toe-in measurement is greater than the specified range (too much toe-out), extend the shorter rack end so that the difference in length is within the specified range.


ii.

If the toe-in measurement is less than the specified range (too much toe-in), shorten the longer rack end so that the difference in length is within the specified range.


iii.

Measure the toe-in.



e.
C317577C06
1.625,0.51 1.781,0.708 0.156,0.198 10 false A 1.667,1.365 1.823,1.563 0.156,0.198 10 false B 1.031,0.323 1.188,0.521 0.156,0.198 10 false C 2.208,0.344 2.365,0.542 0.156,0.198 10 false D
V100135

Front of the Vehicle


Turn the right and left steering rack ends by an equal amount to adjust the toe-in.

HINT:

Perform adjustments so that the value is as close as possible to the median of the specified range.


Toe-in (Unloaded Vehicle):
Engine SUSPENSION TYPE Specified Condition

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)
C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)*
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)
B - A: 1.8 +/- 2.0 mm (0.0709 +/- 0.0787 in.)*
SPORT C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)
2GR-FKS NORMAL C + D: 0°06' +/- 0°10' (0.09° +/- 0.17°)
C + D: 0°09' +/- 0°10' (0.15° +/- 0.17°)*
B - A: 1.1 +/- 2.0 mm (0.0433 +/- 0.0787 in.)
B - A: 1.7 +/- 2.0 mm (0.0669 +/- 0.0787 in.)*
SPORT C + D: 0°07' +/- 0°10' (0.12° +/- 0.17°)
B - A: 1.4 +/- 2.0 mm (0.0551 +/- 0.0787 in.)



f.

Make sure that the thread length of the right and left steering rack ends are the same.


g.

Tighten the tie rod assembly lock nuts.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)


h.
C375205C02
1.01,0.969 1.354,1.198 0.344,0.229 10 false *a 1.229,1.583 1.625,1.854 0.396,0.271 10 false 45° 0.865,1.625 1.24,1.906 0.375,0.281 10 false 90° 2.99,1.594 3.406,1.969 0.417,0.375 10 false 22.5°
*a Clip Tab Positioning Area
V100135

Up
V100136

Rear of Vehicle


Place the steering rack boots on the seats and install the steering rack boot clips.

HINT:
·

Make sure that the steering rack boots are not twisted.

·

Make sure that the tabs of the steering rack boot clip are positioned within the area shown in the illustration.




Hide 8.INSPECT WHEEL ANGLE

a.
C132439C03
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of a turning radius gauge.


b.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


If the right and left inside wheel angles differ from the specified value, check and adjust the right and left steering rack end lengths.


Wheel Turning Angle (Unloaded Vehicle):
Engine SUSPENSION TYPE Tire Size Inside Wheel Outside Wheel

*: for Rough Road Area Specification Vehicles

2AR-FE
A25A-FKS
6AR-FSE
NORMAL 205/65R16
215/55R17
38°10' +/- 2°00' (38.17° +/- 2.00°)
38°30' +/- 2°00' (38.50° +/- 2.00°)*
32°45' (32.75°)
33°00' (33.00°)*
235/45R18 36°50' +/- 2°00' (36.83° +/- 2.00°)
37°20' +/- 2°00' (37.33° +/- 2.00°)*
31°50' (31.83°)
32°15' (32.25°)*
SPORT - 36°50' +/- 2°00' (36.83° +/- 2.00°) 31°55' (31.92°)
2GR-FKS NORMAL 215/55R17 38°25' +/- 2°00' (38.42° +/- 2.00°)* 33°00' (33.00°)*
235/45R18 36°45' +/- 2°00' (36.75° +/- 2.00°)
37°05' +/- 2°00' (37.08° +/- 2.00°)*
31°45' (31.75°)
32°05' (32.08°)*
SPORT - 36°50' +/- 2°00' (36.83° +/- 2.00°) 31°50' (31.83°)



Hide 9. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 10. PERFORM SYSTEM VARIANT LEARNING AND ACCELERATION SENSOR ZERO POINT CALIBRATION