Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light) › 2020.08–2021.02
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0328283 HEADLIGHT ASSEMBLY(for Bulb Type Turn Signal Light) G

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Bulb Type Turn Signal Light)  INSPECTION  


PROCEDURE

Hide 81175 1.INSPECT HEADLIGHT UNIT ASSEMBLY LH (w/ Automatic Headlight Beam Level Control System)

E447825C01
1.083,5.615 1.448,5.833 0.365,0.219 3.417,6.031 3.781,6.25 0.365,0.219 5.76,6.031 6.125,6.25 0.365,0.219 0.875,7.531 1.24,7.75 0.365,0.219 3.385,7.531 3.75,7.75 0.365,0.219 6,7.531 6.365,7.75 0.365,0.219 1.792,6.781 2.333,6.146 true 0.583,6.271 0.938,6.792 true 0.813,6.094 1.063,6.781 true 1.365,6.302 1.417,6.781 true 1.625,6.135 1.521,6.771 true 0.313,6.469 0.646,6.802 true 0.323,7.26 0.698,7.021 true 0.854,7.26 0.927,7.031 true 1.438,7.292 1.396,7.01 true 1.792,7.385 1.646,7.01 true 2.104,7.24 1.781,7.021 true 1.656,6.771 1.917,6.292 true 0.313,0.104 0.625,0.302 0.313,0.198 10 false *1 2.521,5.417 2.833,5.615 0.313,0.198 10 false *a 6.427,3.115 6.74,3.313 0.313,0.198 10 false *b 6.354,2.396 6.667,2.594 0.313,0.198 10 false *b 5.75,1.219 6.063,1.417 0.313,0.198 10 false *c 1.698,1.188 2.01,1.385 0.313,0.198 10 false *d 1.01,0.479 1.323,0.677 0.313,0.198 10 false *e 1.208,5.656 1.521,5.854 0.313,0.198 10 false B 3.542,6.063 3.854,6.26 0.313,0.198 10 false F 5.875,6.042 6.188,6.24 0.313,0.198 10 false G 3.51,7.563 3.823,7.76 0.313,0.198 10 false D 6.135,7.573 6.448,7.771 0.313,0.198 10 false C 1.01,7.573 1.323,7.771 0.313,0.198 10 false E 0.698,2.542 1.01,2.74 0.313,0.198 10 false *d 0.688,7.542 1,7.74 0.313,0.198 10 false *c 5.552,6.063 5.865,6.26 0.313,0.198 10 false *d 3.188,7.552 3.5,7.75 0.313,0.198 10 false *b 5.813,7.552 6.125,7.75 0.313,0.198 10 false *b 2.073,5.969 2.875,6.125 0.802,0.156 10 false DRL/CLL+ 0.281,6.115 0.854,6.344 0.573,0.229 10 false LOLED0 0.531,5.938 1.125,6.167 0.594,0.229 10 false LOLED2 1.167,6.146 1.76,6.375 0.594,0.229 10 false ACTBI 1.438,5.969 2.031,6.198 0.594,0.229 10 false ACTSI 1.281,7.313 1.792,7.51 0.51,0.198 10 false ACTGI 1.719,7.396 2.229,7.594 0.51,0.198 10 false CLL+ 1.948,7.26 2.625,7.438 0.677,0.177 10 false HI_SOL+ 3.229,6.042 3.542,6.24 0.313,0.198 10 false *d 0.896,5.635 1.208,5.833 0.313,0.198 10 false *a 0.083,7.281 0.688,7.469 0.604,0.188 10 false HI_SOL- 0.667,7.281 1.438,7.479 0.771,0.198 10 false TURN- 0.031,6.292 0.833,6.448 0.802,0.156 10 false DRL/CLL- 1.75,6.135 2.521,6.333 0.771,0.198 10 false TURN+
*1 Headlight Unit Assembly LH (Headlight Cord) - -
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)
*b Component without harness connected
(to Headlight LED Unit Assembly LH)
*c Component without harness connected
(to Headlight Leveling Motor LH)
*d Component without harness connected
(to No. 1 Headlight Clearance LED Unit LH)
*e Component without turn signal light installed
(to Turn Signal Light)
- -


a.

Measure the resistance according to the value(s) in the table below.

i.

Inspect the headlight leveling motor circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-7 (ACTBI) - E-1 Always Below 1 Ω
B-8 (ACTSI) - E-2 Always Below 1 Ω
B-17 (ACTGI) - E-3 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


ii.

Inspect the Lo/Hi beam circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 (LOLED2) - D-2 Always Below 1 Ω
B-3 (LOLED0) - D-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


iii.

Inspect the Lo/Hi beam shade circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-20 (HI_SOL+) - C-2 Always Below 1 Ω
B-11 (HI_SOL-) - C-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


iv.

Inspect the clearance light/daytime running light input circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 (DRL/CLL+) - F-1 Always Below 1 Ω
B-1 (DRL/CLL-) - F-3 Always Below 1 Ω
B-19 (CLL+) - F-2 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


v.

Inspect the clearance light/daytime running light output circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
F-4 - G-5 Always Below 1 Ω
F-5 - G-4 Always Below 1 Ω
F-6 - G-3 Always Below 1 Ω
F-7 - G-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).



Hide 81160A 2.INSPECT HEADLIGHT LED UNIT ASSEMBLY LH (w/ Automatic Headlight Beam Level Control System)

E380641C01
0.583,0.438 0.896,0.635 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight LED Unit Assembly LH)


a.

Apply battery voltage to the headlight LED unit assembly LH and check that the Lo/Hi beam shade operates.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Operates normally


If the result is not as specified, replace the headlight LED unit assembly LH.


Hide 8116A 3.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT LH (w/ Automatic Headlight Beam Level Control System)

E380642C01
0.583,0.469 0.896,0.667 0.313,0.198 10 false *a
*a Component without harness connected
(No. 1 Headlight Clearance LED Unit LH)


a.

Apply battery voltage to the No. 1 headlight clearance LED unit LH and check that the light illuminates.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 3
Clearance light/daytime running light illuminates


If the result is not as specified, replace the No. 1 headlight clearance LED unit LH.


Hide 81135 4.INSPECT HEADLIGHT UNIT ASSEMBLY RH (w/ Automatic Headlight Beam Level Control System)

E447825C01
1.083,5.615 1.448,5.833 0.365,0.219 3.417,6.031 3.781,6.25 0.365,0.219 5.76,6.031 6.125,6.25 0.365,0.219 0.875,7.531 1.24,7.75 0.365,0.219 3.385,7.531 3.75,7.75 0.365,0.219 6,7.531 6.365,7.75 0.365,0.219 1.792,6.781 2.333,6.146 true 0.583,6.271 0.938,6.792 true 0.813,6.094 1.063,6.781 true 1.365,6.302 1.417,6.781 true 1.625,6.135 1.521,6.771 true 0.313,6.469 0.646,6.802 true 0.323,7.26 0.698,7.021 true 0.854,7.26 0.927,7.031 true 1.438,7.292 1.396,7.01 true 1.792,7.385 1.646,7.01 true 2.104,7.24 1.781,7.021 true 1.656,6.771 1.917,6.292 true 0.313,0.104 0.625,0.302 0.313,0.198 10 false *1 2.521,5.417 2.833,5.615 0.313,0.198 10 false *a 6.427,3.115 6.74,3.313 0.313,0.198 10 false *b 6.354,2.396 6.667,2.594 0.313,0.198 10 false *b 5.75,1.219 6.063,1.417 0.313,0.198 10 false *c 1.698,1.188 2.01,1.385 0.313,0.198 10 false *d 1.01,0.479 1.323,0.677 0.313,0.198 10 false *e 1.208,5.656 1.521,5.854 0.313,0.198 10 false B 3.542,6.063 3.854,6.26 0.313,0.198 10 false F 5.875,6.042 6.188,6.24 0.313,0.198 10 false G 3.51,7.563 3.823,7.76 0.313,0.198 10 false D 6.135,7.573 6.448,7.771 0.313,0.198 10 false C 1.01,7.573 1.323,7.771 0.313,0.198 10 false E 0.698,2.542 1.01,2.74 0.313,0.198 10 false *d 0.688,7.542 1,7.74 0.313,0.198 10 false *c 5.552,6.063 5.865,6.26 0.313,0.198 10 false *d 3.188,7.552 3.5,7.75 0.313,0.198 10 false *b 5.813,7.552 6.125,7.75 0.313,0.198 10 false *b 2.073,5.969 2.875,6.125 0.802,0.156 10 false DRL/CLL+ 0.281,6.115 0.854,6.344 0.573,0.229 10 false LOLED0 0.531,5.938 1.125,6.167 0.594,0.229 10 false LOLED2 1.167,6.146 1.76,6.375 0.594,0.229 10 false ACTBI 1.438,5.969 2.031,6.198 0.594,0.229 10 false ACTSI 1.281,7.313 1.792,7.51 0.51,0.198 10 false ACTGI 1.719,7.396 2.229,7.594 0.51,0.198 10 false CLL+ 1.948,7.26 2.625,7.438 0.677,0.177 10 false HI_SOL+ 3.229,6.042 3.542,6.24 0.313,0.198 10 false *d 0.896,5.635 1.208,5.833 0.313,0.198 10 false *a 0.083,7.281 0.688,7.469 0.604,0.188 10 false HI_SOL- 0.667,7.281 1.438,7.479 0.771,0.198 10 false TURN- 0.031,6.292 0.833,6.448 0.802,0.156 10 false DRL/CLL- 1.75,6.135 2.521,6.333 0.771,0.198 10 false TURN+
*1 Headlight Unit Assembly RH (Headlight Cord) - -
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Headlight LED Unit Assembly RH)
*c Component without harness connected
(to Headlight Leveling Motor RH)
*d Component without harness connected
(to No. 1 Headlight Clearance LED Unit RH)
*e Component without turn signal light installed
(to Turn Signal Light)
- -


a.

Measure the resistance according to the value(s) in the table below.

i.

Inspect the headlight leveling motor circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-7 (ACTBI) - E-1 Always Below 1 Ω
B-8 (ACTSI) - E-2 Always Below 1 Ω
B-17 (ACTGI) - E-3 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


ii.

Inspect the Lo/Hi beam circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-4 (LOLED2) - D-2 Always Below 1 Ω
B-3 (LOLED0) - D-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


iii.

Inspect the Lo/Hi beam shade circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-20 (HI_SOL+) - C-2 Always Below 1 Ω
B-11 (HI_SOL-) - C-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


iv.

Inspect the clearance light/daytime running light input circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-10 (DRL/CLL+) - F-1 Always Below 1 Ω
B-1 (DRL/CLL-) - F-3 Always Below 1 Ω
B-19 (CLL+) - F-2 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


v.

Inspect the clearance light/daytime running light output circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
F-4 - G-5 Always Below 1 Ω
F-5 - G-4 Always Below 1 Ω
F-6 - G-3 Always Below 1 Ω
F-7 - G-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).



Hide 81140 5.INSPECT HEADLIGHT LED UNIT ASSEMBLY RH (w/ Automatic Headlight Beam Level Control System)

E380641C01
0.583,0.438 0.896,0.635 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight LED Unit Assembly RH)


a.

Apply battery voltage to the headlight LED unit assembly RH and check that the Lo/Hi beam shade operates.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Operates normally


If the result is not as specified, replace the headlight LED unit assembly RH.


Hide 8112A 6.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT RH (w/ Automatic Headlight Beam Level Control System)

E380642C01
0.583,0.469 0.896,0.667 0.313,0.198 10 false *a
*a Component without harness connected
(No. 1 Headlight Clearance LED Unit RH)


a.

Apply battery voltage to the No. 1 headlight clearance LED unit RH and check that the light illuminates.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 3
Clearance light/daytime running light illuminates


If the result is not as specified, replace the No. 1 headlight clearance LED unit RH.


Hide 81175 7.INSPECT HEADLIGHT UNIT ASSEMBLY LH (w/o Automatic Headlight Beam Level Control System)

E388100C02
0.813,5.521 1.198,5.781 0.385,0.26 0.854,7.177 1.24,7.438 0.385,0.26 2.646,7.177 3.031,7.438 0.385,0.26 4.375,7.188 4.76,7.448 0.385,0.26 5.854,7.177 6.24,7.438 0.385,0.26 3.042,5.531 3.427,5.792 0.385,0.26 5.563,5.542 5.948,5.802 0.385,0.26 0.438,5.958 0.781,6.125 false 1.25,6.115 1.563,6.01 false 1.052,6.115 1.396,5.833 false 0.458,6.542 0.792,6.323 false 1.24,6.313 1.573,6.552 false 0.677,6.698 1,6.323 false 0.313,0.25 0.625,0.448 0.313,0.198 10 false *1 3.042,4.854 3.354,5.052 0.313,0.198 10 false *a 6,0.958 6.313,1.156 0.313,0.198 10 false *b 5.719,1.521 6.031,1.719 0.313,0.198 10 false *b 5.969,2.073 6.281,2.271 0.313,0.198 10 false *b 2.896,0.313 3.208,0.51 0.313,0.198 10 false *c 1.5,1.99 1.813,2.188 0.313,0.198 10 false *d 1.938,0.625 2.25,0.823 0.313,0.198 10 false *d 0.365,5.521 0.677,5.719 0.313,0.198 10 false *a 0.875,5.573 1.219,5.771 0.344,0.198 10 false A74 0.208,5.854 0.552,6.052 0.344,0.198 10 false LO 1.458,5.677 1.802,5.875 0.344,0.198 10 false S 1.625,5.906 1.969,6.104 0.344,0.198 10 false E 0.313,6.521 0.656,6.719 0.344,0.198 10 false B 1.615,6.521 1.958,6.719 0.344,0.198 10 false SOL 2.802,7.229 3.146,7.427 0.344,0.198 10 false C 4.531,7.24 4.875,7.438 0.344,0.198 10 false D 6,7.219 6.344,7.417 0.344,0.198 10 false E 3.198,5.583 3.542,5.781 0.344,0.198 10 false F 5.708,5.594 6.052,5.792 0.344,0.198 10 false G 1.01,7.229 1.354,7.427 0.344,0.198 10 false B 2.417,5.583 2.729,5.781 0.313,0.198 10 false *d 5.042,5.583 5.354,5.781 0.313,0.198 10 false *d 1.979,7.448 2.292,7.646 0.313,0.198 10 false *b 3.875,7.448 4.188,7.646 0.313,0.198 10 false *b 5.375,7.438 5.688,7.635 0.313,0.198 10 false *b 0.271,7.458 0.583,7.656 0.313,0.198 10 false *c 0.563,6.74 0.906,6.938 0.344,0.198 10 false B
*1 Headlight Unit Assembly LH (Headlight Cord) - -
*a Component without harness connected
(to Wire Harness)
*b Component without harness connected
(to Headlight LED Unit Assembly LH)
*c Component without harness connected
(to Light Control ECU)
*d Component without harness connected
(to No. 1 Headlight Clearance LED Unit LH)


a.

Measure the resistance according to the value(s) in the table below.

i.

Inspect the Lo/Hi beam circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
A74-1 (E) - B-6 Always Below 1 Ω
A74-2 (S) - B-12 Always Below 1 Ω
A74-3 (LO) - B-7 Always Below 1 Ω
B-4 - D-1 Always Below 1 Ω
B-10 - D-2 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


ii.

Inspect the Lo/Hi beam shade circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
A74-1 (E) - E-2 Always Below 1 Ω
A74-4 (SOL) - E-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


iii.

Inspect the headlight fan circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - C-3 Always Below 1 Ω
B-9 - C-2 Always Below 1 Ω
B-11 - C-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


iv.

Inspect the clearance light/daytime running light input circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
A74-1 (E) - F-3 Always Below 1 Ω
A74-5 (B) - F-2 Always Below 1 Ω
A74-6 (B) - F-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).


v.

Inspect the clearance light/daytime running light output circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
F-4 - G-5 Always Below 1 Ω
F-5 - G-4 Always Below 1 Ω
F-6 - G-3 Always Below 1 Ω
F-7 - G-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly LH (headlight cord).



Hide 81160A 8.INSPECT HEADLIGHT LED UNIT ASSEMBLY LH (w/o Automatic Headlight Beam Level Control System)

a.
E380641C01
0.583,0.438 0.896,0.635 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight LED Unit Assembly LH)


Apply battery voltage to the headlight LED unit assembly LH and check that the Lo/Hi beam shade operates.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Operates normally


If the result is not as specified, replace the headlight LED unit assembly LH.


Hide 8116A 9.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT LH (w/o Automatic Headlight Beam Level Control System)

E380642C01
0.583,0.469 0.896,0.667 0.313,0.198 10 false *a
*a Component without harness connected
(No. 1 Headlight Clearance LED Unit LH)


a.

Apply battery voltage to the No. 1 headlight clearance LED unit LH and check that the light illuminates.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 3
Clearance light/daytime running light illuminates


If the result is not as specified, replace the No. 1 headlight clearance LED unit LH.


Hide 81135 10.INSPECT HEADLIGHT UNIT ASSEMBLY RH (w/o Automatic Headlight Beam Level Control System)

E388100C01
0.813,5.521 1.198,5.781 0.385,0.26 0.854,7.177 1.24,7.438 0.385,0.26 2.646,7.177 3.031,7.438 0.385,0.26 4.375,7.188 4.76,7.448 0.385,0.26 5.854,7.177 6.24,7.438 0.385,0.26 3.042,5.531 3.427,5.792 0.385,0.26 5.563,5.542 5.948,5.802 0.385,0.26 0.438,5.958 0.781,6.125 false 1.25,6.115 1.563,6.01 false 1.052,6.115 1.396,5.833 false 0.458,6.542 0.792,6.323 false 1.24,6.313 1.573,6.552 false 0.708,6.688 1,6.323 false 0.313,0.25 0.625,0.448 0.313,0.198 10 false *1 3.042,4.854 3.354,5.052 0.313,0.198 10 false *a 6,0.958 6.313,1.156 0.313,0.198 10 false *b 5.719,1.521 6.031,1.719 0.313,0.198 10 false *b 5.969,2.073 6.281,2.271 0.313,0.198 10 false *b 2.896,0.313 3.208,0.51 0.313,0.198 10 false *c 1.5,1.99 1.813,2.188 0.313,0.198 10 false *d 1.938,0.625 2.25,0.823 0.313,0.198 10 false *d 0.365,5.521 0.677,5.719 0.313,0.198 10 false *a 0.875,5.573 1.219,5.771 0.344,0.198 10 false A73 0.208,5.854 0.552,6.052 0.344,0.198 10 false LO 1.458,5.677 1.802,5.875 0.344,0.198 10 false S 1.625,5.906 1.969,6.104 0.344,0.198 10 false E 0.313,6.521 0.656,6.719 0.344,0.198 10 false B 1.615,6.521 1.958,6.719 0.344,0.198 10 false SOL 2.802,7.229 3.146,7.427 0.344,0.198 10 false C 4.531,7.24 4.875,7.438 0.344,0.198 10 false D 6,7.219 6.344,7.417 0.344,0.198 10 false E 3.198,5.583 3.542,5.781 0.344,0.198 10 false F 5.708,5.594 6.052,5.792 0.344,0.198 10 false G 1.01,7.229 1.354,7.427 0.344,0.198 10 false B 2.417,5.583 2.729,5.781 0.313,0.198 10 false *d 5.042,5.583 5.354,5.781 0.313,0.198 10 false *d 1.979,7.448 2.292,7.646 0.313,0.198 10 false *b 3.875,7.448 4.188,7.646 0.313,0.198 10 false *b 5.375,7.438 5.688,7.635 0.313,0.198 10 false *b 0.271,7.458 0.583,7.656 0.313,0.198 10 false *c 0.583,6.729 0.927,6.927 0.344,0.198 10 false B
*1 Headlight Unit Assembly RH (Headlight Cord) - -
*a Component without harness connected
(to Wire Harness)
*b Component without harness connected
(to Headlight LED Unit Assembly RH)
*c Component without harness connected
(to Light Control ECU)
*d Component without harness connected
(to No. 1 Headlight Clearance LED Unit RH)


a.

Measure the resistance according to the value(s) in the table below.

i.

Inspect the Lo/Hi beam circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-1 (E) - B-6 Always Below 1 Ω
A73-2 (S) - B-12 Always Below 1 Ω
A73-3 (LO) - B-7 Always Below 1 Ω
B-4 - D-1 Always Below 1 Ω
B-10 - D-2 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


ii.

Inspect the Lo/Hi beam shade circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-1 (E) - E-2 Always Below 1 Ω
A73-4 (SOL) - E-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


iii.

Inspect the headlight fan circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - C-3 Always Below 1 Ω
B-9 - C-2 Always Below 1 Ω
B-11 - C-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


iv.

Inspect the clearance light/daytime running light input circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-1 (E) - F-3 Always Below 1 Ω
A73-5 (B) - F-2 Always Below 1 Ω
A73-6 (B) - F-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).


v.

Inspect the clearance light/daytime running light output circuit.

Standard Resistance:
Tester Connection Condition Specified Condition
F-4 - G-5 Always Below 1 Ω
F-5 - G-4 Always Below 1 Ω
F-6 - G-3 Always Below 1 Ω
F-7 - G-1 Always Below 1 Ω


If the result is not as specified, replace the headlight unit assembly RH (headlight cord).



Hide 81140 11.INSPECT HEADLIGHT LED UNIT ASSEMBLY RH (w/o Automatic Headlight Beam Level Control System)

a.
E380641C01
0.583,0.438 0.896,0.635 0.313,0.198 10 false *a
*a Component without harness connected
(Headlight LED Unit Assembly RH)


Apply battery voltage to the headlight LED unit assembly RH and check that the Lo/Hi beam shade operates.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Operates normally


If the result is not as specified, replace the headlight LED unit assembly RH.


Hide 8112A 12.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT RH (w/o Automatic Headlight Beam Level Control System)

E380642C01
0.583,0.469 0.896,0.667 0.313,0.198 10 false *a
*a Component without harness connected
(No. 1 Headlight Clearance LED Unit RH)


a.

Apply battery voltage to the No. 1 headlight clearance LED unit RH and check that the light illuminates.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 3
Clearance light/daytime running light illuminates


If the result is not as specified, replace the No. 1 headlight clearance LED unit RH.