The ECM calculates and compares the accelerator pedal opening angle value used for control and the value used for monitoring.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P060694 | Control Module Processor Unexpected Operation | Condition where output of the accelerator opening angle value used for control is more excessive than that of the accelerator opening angle value used for monitoring is continuously detected for 0.5 seconds or more (1 trip detection logic). | ·
Accelerator pedal sensor assembly ·
Wire harness or connector ·
ECM |
Comes on | DTC stored | SAE Code: P0606 |
The ECM calculates the accelerator pedal opening angle value used for control and the value used for monitoring. If the ECM determines there is an excessive output while the engine is running, a DTC is stored and the MIL is illuminated.
| Required Sensors/Components | Accelerator pedal sensor assembly |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the GTS off.
Turn the engine switch off.
Disconnect the GTS.
Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
Connect the cable to the negative (-) battery terminal.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
With the vehicle stopped, repeat the accelerator pedal operation (press the accelerator pedal from a state where it is not depressed) several times.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P060694.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
Connect the cable to the negative (-) battery terminal.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
With the vehicle stopped, repeat the accelerator pedal operation (press the accelerator pedal from a state where it is not depressed) several times.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P060694 is output | B |
A
B
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A20-6 (VPA) - A24-55 (VPA) | Always | Below 1 Ω |
| A20-3 (VPA2) - A24-58 (VPA2) | Always | Below 1 Ω |
| A20-4 (VCPA) - A24-57 (VCPA) | Always | Below 1 Ω |
| A20-1 (VCP2) - A24-60 (VCP2) | Always | Below 1 Ω |
| A20-5 (EPA) - A24-56 (EPA) | Always | Below 1 Ω |
| A20-2 (EPA2) - A24-59 (EPA2) | Always | Below 1 Ω |
| A20-6 (VPA) or A24-55 (VPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A20-3 (VPA2) or A24-58 (VPA2) - Body ground and other terminals | Always | 10 kΩ or higher |
| A20-4 (VCPA) or A24-57 (VCPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A20-1 (VCP2) or A24-60 (VCP2) - Body ground and other terminals | Always | 10 kΩ or higher |
| A20-5 (EPA) or A24-56 (EPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A20-2 (EPA2) or A24-59 (EPA2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG