Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2020.08–2021.02
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0344647 SFI SYSTEM(w/o Canister Pump Module) D

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  VEHICLE CONTROL HISTORY  


DESCRIPTION


·

Vehicle Control History is a function that captures and stores ECU data when triggered by specific vehicle behavior.

·

If the customer states that the engine stalled or will not start, it may be possible to diagnose the cause of the malfunction by checking the vehicle history information and freeze frame data.

·

The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.

·

The stored data items for Vehicle Control History Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The contents of the Freeze Frame Data is almost the same as that of the Data List.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>DATA LIST / ACTIVE TEST



PRECAUTIONS


·

As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History before performing any inspections.

·

As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.



CHECK VEHICLE CONTROL HISTORY (SFI SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 1055
HINT:

It is also possible to display Vehicle Control History during the Health Check, if "Store All Data" is selected.


Vehicle Control History Item
Code Item Trigger Description Stored Group Reference Inspection Procedure Link
X0800 Engine Stall
Detection Condition (Engine Stall)
·

Prerequisite Conditions: The engine is running (after engine is judged to be difficult to start)

·

Detection Conditions: The engine speed is decreases to 200 rpm or less, or stops

·

Duration: 0.5 seconds or more


08 Flow chart [Engine Stalls] step 3 (Click here)
The engine stalled due to factors other than the operation of the ignition or starter switch assembly*1 or engine switch*2
X0803 Engine Stall (Compression Leakage) It is judged that the engine stalled due to compression leakage 08 Flow chart [Engine Stalls] step 3 (Click here)
X0810 Engine Difficult to Start (Engine Starting Time Long)
Detection Condition (Engine Starting Time Long)
·

Prerequisite Conditions: STA signal is ON

·

Detection Conditions: The engine speed is less than 500 rpm for a long period of time (the starting time is long or the engine does not start)

·

Duration: Refer to Engine Difficult to Start Duration Judgment Region illustration


09 Flow chart [Engine Difficult to Start] step 3 (Click here)
The engine speed decreases or the engine stalls immediately after starting
X0811 Engine Difficult to Start (Engine Stall Immediately After Starting)
Detection Condition (Engine Stall Immediately After Starting)
·

Prerequisite Conditions: Within 2 seconds after the engine has started (engine speed is 500 rpm or more) and the engine coolant temperature is -15°C (5°F) or more

·

Detection Conditions: The engine speed decreases to 200 rpm or less (immediately after starting, the engine speed decreases or the engine stalls)

·

Duration: -


09 Flow chart [Engine Difficult to Start] step 3 (Click here)
The engine speed decreases or the engine stalls immediately after starting
X0812 Engine Difficult to Start (Immobiliser) Engine difficult to start due to immobiliser 09 Flow chart [Engine Difficult to Start] step 3 (Click here)
X0821 Rough Idle #1
Detection Condition (Rough Idle)
·

Prerequisite Conditions: The engine is idling with the vehicle is stopped and the accelerator pedal is fully released

·

Detection Conditions: It is judged that combustion is unstable due to the instantaneous change in engine speed for each cylinder

·

Duration: Depending on the combustion status, between 2 and 10 seconds


03 Flow chart [Rough Idling] step 3 (Click here)
Idling is rough due to unstable combustion in the No. 1 cylinder
X0822 Rough Idle #2 Idling is rough due to unstable combustion in the No. 2 cylinder 03 Flow chart [Rough Idling] step 3 (Click here)
X0823 Rough Idle #3 Idling is rough due to unstable combustion in the No. 3 cylinder 03 Flow chart [Rough Idling] step 3 (Click here)
X0824 Rough Idle #4 Idling is rough due to unstable combustion in the No. 4 cylinder 03 Flow chart [Rough Idling] step 3 (Click here)
X082A Rough Idle (Plural Cylinders) Idling is rough due to multiple cylinders
As more than one cylinder is affected, the EGR system, fuel system, etc. is suspected
03 Flow chart [Rough Idling] step 3 (Click here)
X082D Rough Idle (Compression Leakage) Idling is judged to be rough due to compression leakage 03 Flow chart [Rough Idling] step 3 (Click here)
X082E Rough Idle (Low Frequency) Slight rough idle symptoms are detected 3 times in 10 trips
HINT:

As the rough idle symptoms are slight, if rough idle codes other than rough idle (low frequency) code X082E are stored, this code will not be stored.


03 Flow chart [Rough Idling] step 3 (Click here)
X0844 Engine Lack of Power
Detection Condition (Engine Lack of Power)
·

Prerequisite Conditions: All of the following conditions are met

-

The accelerator opening angle 80% or more.

-

The engine speed is 400 rpm or more.

-

The intake air temperature is 80°C (176°F) or less.

-

The atmospheric pressure is 61 kPa(abs) [8.70 psi(abs)] or higher.

-

The STP signal is off.

-

The STA signal is off.

-

Shift state is not in P or N.


·

Detects a condition where the output torque is insufficient approximately 65% or more relative to the requested torque (divided value of the output torque is approximately 0.35 less than the requested torque)

·

Duration: 2 seconds or more


04 Flowchart [Lack of Power] step 3 (Click here)
X0845 Engine Lack of Power (Bad Fuel Condition) Engine output is insufficient due to bad quality fuel
(Fuel quality is bad due to fuel aging degradation, water intrusion or fuel additive)
04 Flowchart [Lack of Power] step 3 (Click here)
X0850 Engine Oil Pressure Low The engine oil pressure is low 05 - -
X0851 Engine Coolant Temperature High The engine coolant temperature is high (overheating) 05 - -
X0852 Engine RPM High The engine speed is high (over revving) 05 - -
X0854 Engine Coolant Temperature High (Low Voltage) The engine coolant temperature is high (overheating) due to a low engine water pump assembly voltage causing the engine water pump assembly to stop 05 - -

*1: w/o Smart Key System

*2: w/ Smart Key System


Engine Difficult to Start Duration Judgment Region (Engine Starting Time Long) (X0810)
A220316E34
0.314,1.64 1.192,1.824 0.878,0.184 10 Starting Time 1.276,0.37 1.960,0.554 0.684,0.184 10 (Seconds) 3.844,1.136 5.000,1.486 1.156,0.350 10 Region Indicating Malfunction 6.384,2.761 6.665,2.959 0.281,0.198 10 (°C) 1.43,2.26 1.553,2.437 0.123,0.177 10 2 1.892,2.78 2.132,2.936 0.239,0.156 10 -30 3.517,2.78 3.715,2.950 0.198,0.170 10 20 5.198,2.78 5.410,2.964 0.211,0.184 10 80 3.518,3.178 5.368,3.362 1.850,0.184 10 Engine Coolant Temperature

Stored Data
Stored Group Number of Records Number of Freeze Frame Points Multi Freeze Frame Data Sampling Period Note
03 1 code
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.

·

If rough idle codes other than Rough Idle (Low Frequency) code X082E are stored, data for code X082E will not be overwritten.



7 points (1 point at detection + 6 points before detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal.
04 1 code
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



7 points (1 point at detection + 6 points before detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal.
05 4 codes
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



1 point (multi freeze frame data not available) -
·

The data can be cleared by using the GTS.

·

The data cannot be cleared by disconnecting the cable from the negative (-) battery terminal.


08 1 codes
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



12 points (1 point at detection + 8 points before detection + 3 points after detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds
·

The data can be cleared by using the GTS.

·

The data cannot be cleared by disconnecting the cable from the negative (-) battery terminal.


09 1 code
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



7 points (1 point at detection + 3 points before detection + 3 points after detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal.

HINT:
·

Multi Freeze Frame Data makes it possible to display the engine condition (ECU data) both before and after the trigger detection point.

·

The number of available points differs depending on the stored group.

·

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


A405050E03
2.948,1.552 2.844,1.552 2.844,1.552 2.844,1.385 false 0.156,0.083 2.917,0.323 2.76,0.24 12 false Stored Group 03, 04 1.854,0.635 3.458,0.906 1.604,0.271 10 false Point Before Detection 1.667,2.344 3.802,2.656 2.135,0.313 10 false Recording Time Before Detection 1.094,1.927 3.063,2.188 1.969,0.26 10 false Sampling Cycle (0.5 seconds) 3.542,0.104 5.135,0.396 1.594,0.292 10 false Trigger Detection Point 2.969,1.458 4.177,1.948 1.208,0.49 10 false Freeze Frame Data which can be read

A414224E02
5.406,1.688 5.208,1.615 5.208,1.615 5.208,1.479 false 0.302,0.156 1.677,0.354 1.375,0.198 12 false Stored Group 08 4.156,0.135 5.677,0.323 1.521,0.188 10 false Trigger Detection Point 5.604,0.458 7,0.656 1.396,0.198 10 false Point After Detection 1.885,0.458 3.479,0.688 1.594,0.229 10 false Point Before Detection 2.979,1.958 4.885,2.229 1.906,0.271 10 false Sampling Cycle (0.5 seconds) 5.448,1.615 6.875,2.01 1.427,0.396 10 false Freeze Frame Data which can be read 1.542,2.417 3.667,2.656 2.125,0.24 10 false Recording Time Before Detection 5.167,2.448 7.135,2.677 1.969,0.229 10 false Recording Time After Detection

A412793E01
5.063,1.625 4.927,1.625 4.927,1.625 4.833,1.458 false 3.302,0.177 5.073,0.396 1.771,0.219 10 false Trigger Detection Point 1.573,0.552 3.281,0.813 1.708,0.26 10 false Point Before Detection 4.833,0.542 6.594,0.75 1.76,0.208 10 false Point After Detection 2.031,1.948 4.115,2.198 2.083,0.25 10 false Sampling Cycle (0.5 seconds) 0.198,0.146 1.917,0.417 1.719,0.271 12 false Stored Group 09 5.135,1.563 6.375,2.104 1.24,0.542 10 false Freeze Frame Data which can be read 1.406,2.427 3.802,2.646 2.396,0.219 10 false Recording Time Before Detection 4.458,2.427 6.781,2.656 2.323,0.229 10 false Recording Time After Detection

Only 1 measurement point can be displayed for stored group 05 Freeze Frame Data.


Vehicle Control History Freeze Frame Data
A476272

A476273




CLEAR VEHICLE CONTROL HISTORY (SFI SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) / Clear.

NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.




VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)


HINT:

A part of the control history can be confirmed using the vehicle control history.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>VEHICLE CONTROL HISTORY