Home › Drivetrain › K120 (CVT) › FRONT DIFFERENTIAL OIL SEAL › from 2021.02
RM33A0E _52 Drivetrain _098634 K120 CVT _0461778 FRONT DIFFERENTIAL OIL SEAL A

K120 CVT  FRONT DIFFERENTIAL OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. (Click here)
Front wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 43420H 2.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C391953N01
0.823,0.594 1.198,0.844 true 0.5,0.5 0.823,0.708 0.323,0.208 10 true SST

Using SST, remove the front drive shaft oil seal LH from the continuously variable transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 43410M 3.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C391957N01
0.625,1.063 0.99,1.063 false 0.313,0.979 0.667,1.198 0.354,0.219 10 false SST

Using SST, remove the front drive shaft oil seal RH from the continuously variable transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 43420H 4.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C391954N01
1.698,1.188 1.104,0.677 1.104,0.677 1.625,0.927 true 0.75,0.563 1.083,0.771 0.333,0.208 10 true SST

Using SST and a hammer, install a new front drive shaft oil seal LH to the continuously variable transaxle assembly.

SST
09950-70010  (09951-07100)
09649-17010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal LH in the correct direction.

·

Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal LH.




Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C391952N01
1.958,0.948 1.177,0.427 1.177,0.427 1.885,0.698 true 0.865,0.333 1.302,0.563 0.438,0.229 10 false SST

Using SST and a hammer, install a new front drive shaft oil seal RH to the continuously variable transaxle assembly.

SST
09950-70010  (09951-07100)
09316-10010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal RH in the correct direction.

·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.