Home › General › MAINTENANCE › K120 CONTINUOUSLY VARIABLE TRANSAXLE FLUID › from 2021.02
RM33A0E _V1 General _065356 MAINTENANCE _0461822 K120 CONTINUOUSLY VARIABLE TRANSAXLE FLUID A

MAINTENANCE  K120 CONTINUOUSLY VARIABLE TRANSAXLE FLUID  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during CVT fluid replacement are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 53852K 1.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441 3.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53737B 4.REMOVE FRONT FENDER APRON SEAL LH

Hide 5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE FLUID

a.

Lift the vehicle. [#1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear and side to side of the vehicle is within +/- 1°).



b.
C411637

Remove the refill plug and gasket from the rear transaxle case sub-assembly. [#2]


c.
C411638

Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle case sub-assembly and drain the fluid. [#3]


d.
C411639C01
2.354,0.844 2.635,0.844 true 2.167,0.76 2.396,0.99 0.229,0.229 10 false *1
*1 Overflow (CVT) Tube


Using a 6 mm hexagon socket wrench, remove the overflow (CVT) tube from the transaxle case sub-assembly and drain the fluid. [#4]


e.
C411640

Measure the amount of fluid drained. [#5]

HINT:

Add the same amount of fluid in step [#8].



f.
C411639C01
2.354,0.844 2.635,0.844 true 2.167,0.76 2.396,0.99 0.229,0.229 10 false *1
*1 Overflow (CVT) Tube


Using a 6 mm hexagon socket wrench, install the overflow (CVT) tube to the transaxle case sub-assembly. [#6]

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)


g.
C411638

Using a 10 mm hexagon socket wrench, temporarily install the overflow plug and gasket to the transaxle case sub-assembly. [#7]

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



h.
C411641

Add fluid to the refill plug hole using the same amount of fluid drained in step [#5]. [#8]

NOTICE:

Use Toyota Genuine CVT fluid FE.



i.
C411637

Temporarily install the refill plug and gasket to the rear transaxle case sub-assembly. [#9]

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



j.

Lower the vehicle. [#10]


k.

Start the engine. [#11]


l.

Slowly move the shift lever from P to D, and then back to P (keep the shift lever in each position for approximately 3 seconds). [#12]

HINT:

Slowly move the shift lever to circulate the fluid through each part of the continuously variable transaxle assembly.



m.

Allow the engine assembly to idle for 30 seconds to warm it up. [#13]


n.

Turn the ignition switch off. [#14]


o.

Repeat steps [#1] to [#14].


p.

Repeat steps [#1] to [#10].


Hide 7.ADJUST FLUID TEMPERATURE (when Using the GTS)

Hide 8.ADJUST FLUID TEMPERATURE (when Not Using the GTS)

Hide 10.PERFORM ATF THERMAL DEGRADATION ESTIMATE RESET

NOTICE:

If approximately 50% or more of the CVT fluid has been replaced during a repair of the transaxle or a similar operation, perform ATF Thermal Degradation Estimate Reset.

Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


Hide 53737B 12.INSTALL FRONT FENDER APRON SEAL LH

Hide 51441 13.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53852K 14.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 15.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH