Home › General › SPECIFICATIONS › K120 CVT › from 2021.02
RM33A0E _V1 General _065355 SPECIFICATIONS _0461648 K120 CVT F

SPECIFICATIONS  K120 CVT  SERVICE DATA  


Continuously Variable Transaxle System
Engine stall speed D 2350 +/- 300 rpm
Fluid pressure (Throttle valve fully opened)*1
Engine stall speed
2350 +/- 300 rpm
D 3.5 to 4.3 MPa
(35.7 to 43.8 kgf/cm2, 508 to 624 psi)
R 1.6 to 2.4 MPa
(16.3 to 24.5 kgf/cm2, 232 to 348 psi)
Time lag N → D Less than 1.2 seconds
N → R Less than 1.5 seconds

Speed Variation Chart:
Shift Lever Position Drive Mode Accelerator Pedal Position
(Vehicle Speed)
Fully Depressed
(Before 1st up-shift)
*1
Fully Depressed
(Before 2nd up-shift)
*2
Constant Position
(30 km/h (19 mph))
*5
Constant Position
(70 km/h (43 mph))
*4
Constant Position
(100 km/h (62 mph))
*3
Fully Depressed
(Accelerating from 30 km/h (19 mph))
*6
D Normal 6100 to 6900 rpm 6100 to 6900 rpm 750 to 1200 rpm 1000 to 1500 rpm 1300 to 1800 rpm 2500 rpm or more
D Sport 6100 to 6900 rpm 6100 to 6900 rpm 1500 to 1950 rpm 2050 to 2500 rpm 2400 to 2900 rpm 2500 rpm or more


Lock-up Schedule:
Shift Lever Position Lock-up Condition
(Accelerator Pedal Opening Angle)
Lock-up ON
(5%)
Lock-up OFF
(0%)
D 10 to 30 km/h
(6 to 19 mph)
5 to 20 km/h
(3 to 12 mph)


1.

With the vehicle stopped, fully depress the accelerator pedal and check the engine speed at the shift timing listed in *1 and *2 in the speed variation chart.

2.

With the vehicle stopped, depress the accelerator pedal to a constant intermediate position and check the engine speed when the vehicle reaches the vehicle speed listed in *3 in the speed variation chart.

3.

Release the accelerator pedal and check the engine speed when the vehicle decelerates to the vehicle speed listed in *4 in the speed variation chart.

4.

Release the accelerator pedal and check the engine speed when the vehicle decelerates to the vehicle speed listed in *5 in the speed variation chart.

5.

Fully depress the accelerator pedal and check the engine speed as the vehicle accelerates from the vehicle speed listed in *6 in the speed variation chart.


Continuously Variable Transaxle Fluid
Dry fill 8.3 liters (8.8 US qts, 7.3 Imp. qts) Toyota Genuine CVT fluid FE

Continuously Variable Transaxle Unit
Input shaft sub-assembly Standard input shaft end play 0.345 to 1.357 mm (0.0136 to 0.0534 in.)
Clearance of C-1 clutch Pack clearance (Reference) 0.45 to 0.75 mm (0.0177 to 0.0295 in.)
Forward clutch flange thickness Part number Thickness (mm (in.)) Mark
35635-12350 3.3 (0.130) B
35635-12360 3.4 (0.134) C
35635-12370 3.5 (0.138) D
35635-12380 3.6 (0.142) E
35635-12390 3.7 (0.146) F
35635-12400 3.8 (0.150) G
Forward clutch return spring sub-assembly Standard free length 18.54 mm (0.730 in.)
Planetary gear assembly Standard clearance 0.16 to 0.61 mm (0.00630 to 0.0240 in.)
Clearance of B-1 brake Pack clearance 0.539 to 1.321 mm (0.0212 to 0.0520 in.)
1st and reverse brake return spring sub-assembly Standard free length 17.56 mm (0.691 in.)
Thrust needle roller bearing and thrust bearing race diameter Mark Thrust bearing race diameter inside / outside
mm (in.)
Thrust needle roller bearing diameter inside / outside
mm (in.)
A - 47.75 (1.88) / 65.8 (2.59)
B 26.38 (1.04) / 38.9 (1.53) 24.9 (0.98) / 38.9 (1.53)
C - 29.7 (1.17) / 49.1 (1.93)
Straight pin Protrusion height 7.0 to 8.0 mm (0.276 to 0.315 in.)
Differential case tapered roller bearing preload (at 10 rpm) Standard turning torque 1.65 to 2.66 N*m (17 to 27 kgf*cm, 15 to 23 in.*lbf)
Shim thickness Part number Thickness (mm (in.)) Mark
90564-66038 1.76 (0.0693) A
90564-66039 1.79 (0.0705) B
90564-66067 1.82 (0.0717) C
90564-66068 1.85 (0.0728) D
90564-66069 1.88 (0.0740) E
90564-66070 1.91 (0.0752) F
90564-66071 1.94 (0.0764) G
90564-66072 1.97 (0.0776) H
90564-66073 2.00 (0.0787) J
90564-66074 2.03 (0.0799) K
90564-66075 2.06 (0.0811) L
90564-66076 2.09 (0.0823) M
90564-66077 2.12 (0.0835) N
90564-66078 2.15 (0.0846) P
90564-66079 2.18 (0.0858) Q
90564-66080 2.21 (0.0870) R
90564-66081 2.24 (0.0882) S
90564-66082 2.27 (0.0894) T
90564-66083 2.30 (0.0906) U
90564-66084 2.33 (0.0917) V
Adjust reduction driven gear tapered roller bearing preload (at 10 rpm) Standard turning torque Differential case tapered roller bearing preload + 3.21 to 6.11 N*m (33 to 62 kgf*cm, 29 to 54 in.*lbf)
Shim thickness Part number Thickness (mm (in.)) Mark
90564-44070 1.59 (0.0626) A
90564-44071 1.62 (0.0638) B
90564-44072 1.65 (0.0650) C
90564-44073 1.68 (0.0661) D
90564-44074 1.71 (0.0673) E
90564-44075 1.74 (0.0685) F
90564-44076 1.77 (0.0697) G
90564-44077 1.80 (0.0709) H
90564-44078 1.83 (0.0720) J
90564-44079 1.86 (0.0732) K
90564-44080 1.89 (0.0744) L
90564-44081 1.92 (0.0756) M
90564-44082 1.95 (0.0768) N
90564-44083 1.98 (0.0780) P
90564-44084 2.01 (0.0791) Q
90564-44085 2.04 (0.0803) R
90564-44086 2.07 (0.0815) S
90564-44087 2.10 (0.0827) T
90564-44088 2.13 (0.0839) U
90564-44089 2.16 (0.0850) V
90564-44090 2.19 (0.0862) W
90564-44091 2.22 (0.0874) X
90564-44092 2.25 (0.0886) Y
Front drive shaft oil seal LH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Transaxle housing type T oil seal Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Front drive shaft oil seal RH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

Torque Converter and Drive Plate
Drive plate runout Maximum 0.30 mm (0.0118 in.)

Front Differential Oil Seal
Front drive shaft oil seal LH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
Front drive shaft oil seal RH Standard depth -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

Revolution Sensor (NT Sensor)
Transmission revolution sensor (NT)
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low signal 4 to 8 mA
High signal 12 to 16 mA

Revolution Sensor (NOUT Sensor)
Transmission revolution sensor (NOUT)
Tester Connection Condition Specified Condition
1 (NOO) - 2 (NOB) Low signal 4 to 8 mA
High signal 12 to 16 mA

Revolution Sensor (NSS Sensor)
Transmission revolution sensor (NSS)
Tester Connection Condition Specified Condition
1 (NSSO) - 2 (NSSB) Low signal 4 to 8 mA
High signal 12 to 16 mA

Shift Stroke Sensor
Shift stroke sensor
Standard voltage (Combined dry-cell battery voltage of 4.5 V)
Tester Connection Condition Specified Condition
4 (VOUT) - 3 (GND) High signal 4.09 to 4.19 V
Low signal 0.36 to 0.45 V
Reference voltage (Combined dry-cell battery voltage of 5.0 V)
Tester Connection Condition Specified Condition
4 (VOUT) - 3 (GND) High signal 4.55 to 4.65 V
Low signal 0.4 to 0.5 V

Park/Neutral Position Switch
Park/neutral position switch assembly
Tester Connection Condition Specified Condition
2 (RB) - 6 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
2 (RB) - 9 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever in D, M, "+" or "-" Below 1 Ω
Shift lever not in D, M, "+" or "-" 10 kΩ or higher

Shift Lever
Shift lock control unit assembly (w/ Smart Entry and Start System)
Wire harness:
Tester Connection Condition Specified Condition
4 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 Ω
5 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
1 (E) - Body ground Always Below 1 Ω
Shift lock solenoid:
Tester Connection Condition Specified Condition
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
1 (SLS+) - 2 (SLS-) Always 112 Ω
Shift lock control unit assembly (w/o Smart Entry and Start System)
Wire harness:
Tester Connection Condition Specified Condition
1 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
4 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
7 (E) - Body ground Always Below 1 Ω
5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
Shift lock solenoid:
Tester Connection Condition Specified Condition
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω
1 (SLS+) - 2 (SLS-) Always 112 Ω
Transmission control switch
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
Shift lever not in S, "+" or "-" 10 kΩ or higher
3 (SFTU) - 2 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+"
(Up-shift)
10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-"
(Down-shift)
10 kΩ or higher

Valve Body Assembly
Shift solenoid valve (SLG, SL1, SL2, SLU, SLP, SLS)
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω