Home › Engine / Hybrid System › M20A-FKS (COOLING) › FLOW SHUTTING VALVE (for CVT) › from 2021.02
RM33A0E _51 Engine / Hybrid System _098633 M20A-FKS COOLING _0461857 FLOW SHUTTING VALVE(for CVT) A

M20A-FKS COOLING  FLOW SHUTTING VALVE(for CVT)  INSTALLATION  


PROCEDURE

Hide 16264D 1.INSTALL FLOW SHUTTING VALVE (NO. 2 WATER BY-PASS HOSE)

a.
A443827C01
0.885,2.625 0.958,2.292 0.958,2.292 1.063,2.656 false 2.365,3.115 2.365,2.677 false 0.875,2.073 1.188,2.229 0.313,0.156 10 false *a 0.615,3.01 0.927,3.167 0.313,0.156 10 false *b 2.917,2.563 3.229,2.719 0.313,0.156 10 false *c 2.125,2.042 2.438,2.198 0.313,0.156 10 false *d 1.698,2.542 2.01,2.698 0.313,0.156 10 false *e 2.302,3.125 2.615,3.281 0.313,0.156 10 false *a
*a Paint Mark
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c 120° (Tabs of Clip Installation Area)
*d Rear Side of Vehicle
*e Right Side of Vehicle


Install the flow shutting valve (No. 2 water by-pass hose) with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Connect the flow shutting valve (No. 2 water by-pass hose) to the transmission oil cooler and slide the clip to secure it.

NOTICE:
·

Make sure to slide the flow shutting valve (No. 2 water by-pass hose) until it contacts the hose stopper of the transmission oil cooler.

·

Make sure to align the paint mark of the flow shutting valve (No. 2 water by-pass hose) with the paint mark of the transmission oil cooler.

·

Make sure that the tabs of the clip are within the area shown in the illustration.




c.
A443825C01
2.031,2.458 2.438,2.458 false 1.448,2.125 1.292,2.125 1.292,2.125 1.063,2.604 false 0.646,2.135 0.792,2.135 0.792,2.135 0.927,2.583 false 1.854,2.354 2.167,2.51 0.313,0.156 10 false *a 0.469,2.042 0.781,2.198 0.313,0.156 10 false *b 0.615,3.042 0.875,3.198 0.26,0.156 10 false *c 2.5,1.844 2.813,2 0.313,0.156 10 false *d 2.385,3 2.688,3.208 0.302,0.208 10 false *e 1.49,2.021 1.802,2.177 0.313,0.156 10 false *a 2.906,2.542 3.208,2.75 0.302,0.208 10 false *f
*a Paint Mark
*b Protrusion
*c 2 to 7 mm (0.0787 to 0.276 in.)
*d 120° (Tabs of Clip Installation Area)
*e Lower Side of Vehicle
*f Right Side of Vehicle


Connect the No. 4 water by-pass hose to the flow shutting valve (No. 2 water by-pass hose) and slide the clip to secure it.

NOTICE:
·

Make sure to align the paint mark of the No. 4 water by-pass hose with the protrusion of the flow shutting valve (No. 2 water by-pass hose).

·

Make sure to slide the No. 4 water by-pass hose until it contacts the hose stopper of the flow shutting valve (No. 2 water by-pass hose).

·

Make sure that the tabs of the clip are within the area shown in the illustration.




d.

Connect the flow shutting valve (No. 2 water by-pass hose) connector.


Hide 2.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 3.ADD ENGINE COOLANT