The TCM communicates with the ECM via CAN communication.
If a problem occurs in this communication, the TCM stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | No communication between the TCM and ECM for 1.25 seconds or more (1-trip detection logic) | ·
Harness and connector ·
ECM ·
TCM |
Comes on | DTC stored | SAE Code:
U0100 |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 3 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Wait for 3 seconds or more with the ignition switch ON.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: U010087.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Disconnect the C111 TCM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C111-1 (+B) - C111-2 (E1) | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Connect the C111 TCM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A24 ECM connector.
Disconnect the C111 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C111-18 (CAN+) - A24-7 (CANP) | Always | Below 1 Ω |
| C111-17 (CAN-) - A24-17 (CANN) | Always | Below 1 Ω |
| C111-18 (CAN+) or A24-7 (CANP) - Body ground | Always | 10 kΩ or higher |
| C111-17 (CAN-) or A24-17 (CANN) - Body ground | Always | 10 kΩ or higher |
Connect the C111 TCM connector.
Connect the A24 ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT
Perform Registration and Initialization.
for Registration: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC U010087 is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT