Home › Drivetrain › K120 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2021.02
RM33A0E _52 Drivetrain _098634 K120 CVT _0461913 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P158504  Acceleration Sensor Circuit System Internal Failure  


DESCRIPTION

The yaw rate and acceleration sensor is built into the airbag sensor assembly. The airbag sensor assembly sends yaw rate and acceleration sensor signals to the TCM via CAN communication. These signals are used for neutral control. If a yaw rate and acceleration sensor malfunction signal is received from the airbag sensor assembly, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P158504 Acceleration Sensor Circuit System Internal Failure Yaw rate and acceleration sensor malfunction signal (abnormal yaw rate and acceleration sensor value) is received from the airbag sensor assembly for 3 seconds or more (1-trip detection logic).
·

Yaw rate and acceleration sensor (Airbag sensor assembly)

·

CAN communication system

·

Wire harness or connector

·

TCM


Does not come on DTC stored SAE Code:
P1585

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Drive the vehicle while accelerating and decelerating repeatedly for several minutes.

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P158504.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C399500E16
0.448,3.458 4.115,3.656 3.667,0.198 10 false : CAN Communication Line 1.198,1.156 2.802,1.552 1.604,0.396 10 false Brake Actuator Assembly (Skid Control ECU) 1.208,1.01 1.667,1.208 0.458,0.198 10 false A43 1.156,2.635 1.615,2.833 0.458,0.198 10 false K73 1.135,2.823 3.021,3.229 1.885,0.406 10 false Airbag Sensor Assembly (Yaw Rate and Acceleration Sensor) 3.76,2.615 4.219,2.813 0.458,0.198 10 false K76 3.729,2.781 5.677,3.344 1.948,0.563 10 false Central Gateway ECU (Network Gateway ECU) 6.156,2.771 6.615,2.969 0.458,0.198 10 false C111 6.156,2.917 6.615,3.115 0.458,0.198 10 false TCM 0.396,2.083 1.771,2.281 1.375,0.198 10 false A/BAG-IG2 1.656,1.948 2.115,2.146 0.458,0.198 10 false IG2 1.667,2.219 2.125,2.417 0.458,0.198 10 false E1 1.667,2.479 2.115,2.677 0.448,0.198 10 false E2 1.979,2.417 2.438,2.615 0.458,0.198 10 false CANL 1.948,2.042 2.406,2.24 0.458,0.198 10 false CANH 1.948,0.76 2.406,0.958 0.458,0.198 10 false CANL 1.938,0.396 2.396,0.594 0.458,0.198 10 false CANH 2.469,0.177 2.927,0.375 0.458,0.198 10 false 5 2.448,0.563 2.906,0.76 0.458,0.198 10 false 19 2.448,1.844 2.906,2.042 0.458,0.198 10 false 26 2.448,2.229 2.906,2.427 0.458,0.198 10 false 27 1.396,2.104 1.854,2.302 0.458,0.198 10 false 33 1.396,1.833 1.854,2.031 0.458,0.198 10 false 36 1.396,2.365 1.854,2.563 0.458,0.198 10 false 32 3.979,2.219 4.438,2.417 0.458,0.198 10 false 7 3.917,1.844 4.375,2.042 0.458,0.198 10 false 22 4.188,2.021 4.646,2.219 0.458,0.198 10 false CA2H 4.188,2.427 4.646,2.625 0.458,0.198 10 false CA2L 4.708,2.427 5.167,2.625 0.458,0.198 10 false CA4L 4.688,2.031 5.146,2.229 0.458,0.198 10 false CA4H 5.146,1.844 5.604,2.042 0.458,0.198 10 false 18 5.146,2.219 5.604,2.417 0.458,0.198 10 false 17 5.948,2.427 6.406,2.625 0.458,0.198 10 false CANL 5.938,2.042 6.396,2.24 0.458,0.198 10 false CANH 5.677,1.844 6.135,2.042 0.458,0.198 10 false 15 5.667,2.229 6.125,2.427 0.458,0.198 10 false 16

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Read freeze frame data using the GTS. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P158504)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

HINT:
·

If any CAN communication system DTCs are output, perform troubleshooting for the CAN communication system first.

·

If any DTCs other than P158504 are output, troubleshoot those DTCs first.




Result:
Result Proceed to
Only DTC P158504 is output A
DTC P158504 and other DTCs are output B



A

2.INSPECT AIRBAG SENSOR ASSEMBLY (CHECK SENSOR INSTALLATION)

B

2.INSPECT AIRBAG SENSOR ASSEMBLY (CHECK SENSOR INSTALLATION)
a.

Check the airbag sensor assembly installation condition.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The airbag sensor assembly is not tilted and its installation bolts are tightened to the specified torque, the airbag sensor assembly bracket is not deformed and there are no foreign objects under the airbag sensor assembly.



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIRBAG SENSOR ASSEMBLY)

NG

5.REINSTALL OR REPLACE AIRBAG SENSOR ASSEMBLY
3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the K73 airbag sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K73-36 (IG2) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K73-33 (E1) - Body ground Always Below 1 Ω
K73-32 (E2) - Body ground Always Below 1 Ω



f.

Connect the K73 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AIRBAG SENSOR ASSEMBLY POWER SOURCE CIRCUIT)

4.REPLACE AIRBAG SENSOR ASSEMBLY

Result:
Proceed to
NEXT



NEXT

6.PERFORM INITIALIZATION
5.REINSTALL OR REPLACE AIRBAG SENSOR ASSEMBLY
a.

Reinstall or replace the airbag sensor assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION


Result:
Proceed to
NEXT



NEXT

6.PERFORM INITIALIZATION
6.PERFORM INITIALIZATION

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED (DTC P158504)
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED (DTC P158504)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Transmission / Trouble Codes.


h.

Read the DTCs.

Powertrain > Transmission > Trouble Codes
50001 373

Result:
Result Proceed to
DTCs are not output A
DTC P158504 is output B



A

END

B

8.REPLACE TCM
8.REPLACE TCM
a.

Replace the TCM.

Click hereDrivetrain>K120 (CVT)>TCM>COMPONENTS


Result:
Proceed to
NEXT



NEXT

PERFORM REGISTRATION AND INITIALIZATION