The transmission revolution sensor (NC1) detects the intermediate shaft (C1 clutch) speed and sends it to the TCM.
The TCM determines if gear mode should be entered by comparing the transmission revolution sensor (NT) and (NC1) signals.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P274512 | Intermediate Shaft Speed Sensor "B" Circuit Short to Battery | The transmission revolution sensor (NC1) signal is normal but the transmission revolution sensor (NC1) output voltage is higher than 1.8 V for 4.5 seconds or more (1-trip detection logic). | ·
Wire harness or connector ·
Transmission revolution sensor (NC1) ·
TCM ·
Transmission wire |
Comes on | DTC stored | SAE Code:
P07C8 |
| P274514 | Intermediate Shaft Speed Sensor "B" Circuit Short to Ground or Open | The transmission revolution sensor (NC1) signal is normal but the transmission revolution sensor (NC1) output voltage is less than 0.2 V for 4.5 seconds or more (1-trip detection logic) | ·
Wire harness or connector ·
Transmission revolution sensor (NC1) ·
TCM ·
Transmission wire |
Comes on | DTC stored | SAE Code:
P07C7 |
| P274531 | Intermediate Shaft Speed Sensor "B" No Signal | When the transmission revolution sensor (NOUT) signal indicates 300 rpm or more and the SPD signal indicates 10 km/h (6 mph) or more, transmission revolution sensor (NC1) signal indicates less than 300 rpm for 5 seconds or more (1-trip detection logic). | ·
Wire harness or connector ·
Transmission revolution sensor (NC1) ·
TCM ·
Transmission wire |
Comes on | DTC stored | SAE Code:
P2747 |
The TCM receives signals from the transmission revolution sensor (NC1) installed to the continuously variable transaxle and determines the intermediate shaft (C1 clutch) speed.
If the TCM detects no signal from the transmission revolution sensor (NC1) even while the vehicle is being driven, it will determine that in the transmission revolution sensor (NC1) is malfunctioning, illuminate the MIL and store a DTC.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Perform the D Position Shift Test inspection in Road Test.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P274512, P274514 or P274531.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Strictly observe posted speed limits, traffic laws and road conditions.
Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.
Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.
Do not operate the GTS while driving the vehicle.
Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| NC1 Sensor Speed | Intermediate shaft (C1 clutch) speed (NC1) | Min.: 0 rpm
Max.: 65535 rpm |
·
0 rpm: Vehicle stopped and synchronizer engaged ·
Equal to NT Sensor Speed: Vehicle being driven in gear mode |
- |
| NC1 Sensor Voltage | Transmission revolution sensor (NC1) output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) | - |
| Tester Display |
|---|
| NC1 Sensor Speed |
| NC1 Sensor Voltage |
| Result | Proceed to |
|---|---|
| Data List values are normal | A |
| Data List values are not normal | B |
A
B
NEXT
for Registration: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Disconnect the C112 transmission wire connector.
Disconnect the C111 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C112-16 (NC1B) - C111-24 (NC1B) | Always | Below 1 Ω |
| C112-17 (NC1O) - C111-8 (NC1O) | Always | Below 1 Ω |
| C111-2 (E1) - Body ground | Always | Below 1 Ω |
| C112-16 (NC1B) or C111-24 (NC1B) - Body ground and other terminals | Always | 10 kΩ or higher |
| C112-17 (NC1O) or C111-8 (NC1O) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C111 TCM connector.
Connect the C112 transmission wire connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Transmission Wire) |
Disconnect the C112 transmission wire connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C112-16 (NC1B) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Connect the C112 transmission wire connector.
Disconnect the C111 TCM connector.
| *a | Component without harness connected
(TCM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 8 (NC1O) - 2 (E1) | Always | 99 to 101 Ω |
Connect the C111 TCM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C112 transmission wire connector.
| *1 | Transmission Wire |
| *a | Transmission Revolution Sensor Side |
| *b | Wire Harness Connector Side |
Disconnect the transmission wire connector from the transmission revolution sensor (NC1).
Click hereDrivetrain>K120 (CVT)>REVOLUTION SENSOR (NC1 SENSOR)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (transmission revolution sensor side) - 16 (NC1B) (wire harness connector side) | Always | Below 1 Ω |
| 2 (transmission revolution sensor side) - 17 (NC1O) (wire harness connector side) | Always | Below 1 Ω |
| 1 (transmission revolution sensor side) or 16 (NC1B) (wire harness connector side) - All other terminals | Always | 10 kΩ or higher |
| 2 (transmission revolution sensor side) or 17 (NC1O) (wire harness connector side) - All other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT
for Registration: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION