The park/neutral position switch assembly and transmission control switch (shift lock control unit assembly) detect the shift lever position and send signals to the TCM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P070513 | Transmission Range Sensor "A" Circuit Open | P, R, N and D input signals are all OFF simultaneously for 60 seconds or more (2-trip detection logic). | ·
Wire harness or connector ·
Park/neutral position switch assembly ·
TCM |
Comes on | DTC stored | SAE Code:
P0705 |
| P070562 | Transmission Range Sensor "A" Signal Compare Failure | Either of the following conditions is met for 2 seconds or more (2-trip detection logic).
·
2 or more of the following signals are ON simultaneously*1: -
P or N input signal -
R input signal -
D input signal ·
Any of the following signals are ON simultaneously with the shift lever in M*2: -
P input signal -
R input signal -
N input signal |
·
Wire harness or connector ·
Park/neutral position switch assembly ·
Transmission control switch (Shift lock control unit assembly) ·
TCM |
Comes on | DTC stored | SAE Code:
P0705 |
| Vehicle Condition | ||||||
|---|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | Pattern 5 | ||
| Diagnostic Condition | Ignition switch is ON | ○ | ○ | ○ | ○ | ○ |
| Battery voltage is 8 V or more | ○ | ○ | ○ | ○ | ○ | |
| Malfunction Condition | P input signal is ON | ○ | ○ | - | - | - |
| R input signal is ON | ○ | - | ○ | - | ○ | |
| N input signal is ON | - | - | ○ | ○ | - | |
| D input signal is ON | - | ○ | - | ○ | ○ | |
| Duration | 2 seconds or more | 2 seconds or more | 2 seconds or more | 2 seconds or more | 2 seconds or more | |
| Detection Logic | 2-trip detection logic | 2-trip detection logic | 2-trip detection logic | 2-trip detection logic | 2-trip detection logic | |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnostic Condition | Ignition switch is ON | ○ | ○ | ○ |
| Battery voltage is 8 V or more | ○ | ○ | ○ | |
| Malfunction Condition | P input signal is ON | ○ | - | - |
| R input signal is ON | - | ○ | - | |
| N input signal is ON | - | - | ○ | |
| M input signal is ON | ○ | ○ | ○ | |
| Duration | 2 seconds or more | 2 seconds or more | 2 seconds or more | |
| Detection Logic | 2-trip detection logic | 2-trip detection logic | 2-trip detection logic | |
DTC P070562 is stored when any of the above detection patterns is met.
These DTCs indicate a problem with the park/neutral position switch assembly, transmission control switch or wire harness of their circuits.
The park/neutral position switch assembly detects the shift lever position and sends a signal to the TCM. For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch assembly sends a signal to the TCM according to the shift lever position (P, R, N or D).
The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will then illuminate the MIL and store a DTC.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Wait with the shift lever in each position (P, R, N or D) for 60 seconds or more each with the ignition switch ON.
Wait for 2 seconds or more with the shift lever in M.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P070513 or P070562.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift SW Status (P Range) | Park/neutral position switch assembly status | OFF or ON | ·
OFF: Shift lever not in P ·
ON: Shift lever in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Shift SW Status (R Range) | Park/neutral position switch assembly status | OFF or ON | ·
OFF: Shift lever not in R ·
ON: Shift lever in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Shift SW Status (N Range) | Park/neutral position switch assembly status | OFF or ON | ·
OFF: Shift lever not in N ·
ON: Shift lever in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Shift SW Status (D Range) | Park/neutral position switch assembly status | OFF or ON | ·
OFF: Shift lever not in D ·
ON: Shift lever in D |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Tester Display |
|---|
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (N Range) |
| Shift SW Status (D Range) |
| Result | Proceed to |
|---|---|
| Data List values are normal | A |
| Data List values are not normal | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift SW Status (S Range) | Transmission control switch status | OFF or ON | ·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Tester Display |
|---|
| Shift SW Status (S Range) |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
B
Disconnect the K29 shift lock control unit assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K29-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| K29-4 (IG) - Body ground | Ignition switch off | Below 1 V |
Connect the K29 shift lock control unit assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch )) |
Disconnect the K29 shift lock control unit assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (IG) - 5 (S) | Shift lever in M, "+" or "- " | Below 1 Ω |
| 4 (IG) - 5 (S) | Shift lever not in M, "+" or "-" | 10 kΩ or higher |
Connect the K29 shift lock control unit assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K29 shift lock control unit assembly connector.
Disconnect the C111 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K29-5 (S) - C111-14 (S) | Always | Below 1 Ω |
| K29-5 (S) or C111-14 (S) - Body ground | Always | 10 kΩ or higher |
Connect the C111 TCM connector.
Connect the K29 shift lock control unit assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT
for Registration: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Disconnect the C55 park/neutral position switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C55-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| C55-2 (RB) - Body ground | Ignition switch off | Below 1 V |
Connect the C55 park/neutral position switch assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Park/Neutral Position Switch Assembly) |
Disconnect the C55 park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (RB) - 6 (PL) | Shift lever in P | Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher | |
| 2 (RB) - 1 (RL) | Shift lever in R | Below 1 Ω |
| Shift lever not in R | 10 kΩ or higher | |
| 2 (RB) - 9 (NL) | Shift lever in N | Below 1 Ω |
| Shift lever not in N | 10 kΩ or higher | |
| 2 (RB) - 7 (DL) | Shift lever in D, M, "+" or "-" | Below 1 Ω |
| Shift lever not in D, M, "+" or "-" | 10 kΩ or higher |
Connect the C55 park/neutral position switch assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C55 park/neutral position switch assembly connector.
Disconnect the C111 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C55-6 (PL) - C111-29 (P) | Always | Below 1 Ω |
| C55-1 (RL) - C111-30 (R) | Always | Below 1 Ω |
| C55-9 (NL) - C111-32 (N) | Always | Below 1 Ω |
| C55-7 (DL) - C111-31 (D) | Always | Below 1 Ω |
| C55-6 (PL) or C111-29 (P) - Body ground and other terminals | Always | 10 kΩ or higher |
| C55-1 (RL) or C111-30 (R) - Body ground and other terminals | Always | 10 kΩ or higher |
| C55-9 (NL) or C111-32 (N) - Body ground and other terminals | Always | 10 kΩ or higher |
| C55-7 (DL) or C111-31 (D) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C111 TCM connector.
Connect the C55 park/neutral position switch assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT
for Registration: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION