Home › Drivetrain › K120 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2021.02
RM33A0E _52 Drivetrain _098634 K120 CVT _0461913 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM J

K120 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to M, it is possible to change the shift range between M1 and M10 using the shift lever. Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" lowers the shift range by one.

WIRING DIAGRAM

C411325E21
0.198,0.625 1.135,1.156 0.938,0.531 10 false from ECU-ACC Fuse 1.719,2.646 3.771,3.188 2.052,0.542 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 1.719,2.49 2.031,2.688 0.313,0.198 10 false K29 2.073,0.49 2.385,0.688 0.313,0.198 10 false IG 2.063,1.854 2.375,2.042 0.313,0.188 10 false E 3.271,0.5 3.583,0.688 0.313,0.188 10 false S 3.031,1.177 3.646,1.375 0.615,0.198 10 false SFTU 3.031,1.854 3.646,2.052 0.615,0.198 10 false SFTD 5.521,0.5 5.833,0.688 0.313,0.188 10 false S 5.51,1.167 6.125,1.365 0.615,0.198 10 false SFTU 5.521,1.854 6.135,2.052 0.615,0.198 10 false SFTD 5.844,2.5 6.385,2.844 0.542,0.344 10 false C111 5.844,2.656 6.25,3.271 0.406,0.615 10 false TCM 1.854,0.49 2.01,0.688 0.156,0.198 10 false 4 1.865,1.854 2.177,2.052 0.313,0.198 10 false 2 3.5,1.854 3.813,2.052 0.313,0.198 10 false 1 3.5,1.177 3.813,1.375 0.313,0.198 10 false 3 3.51,0.5 3.823,0.698 0.313,0.198 10 false 5 5.25,0.49 5.563,0.688 0.313,0.198 10 false 14 5.25,1.167 5.563,1.365 0.313,0.198 10 false 28 5.25,1.854 5.563,2.052 0.313,0.198 10 false 27 6.25,1.01 6.708,1.208 0.458,0.198 10 false 12 V 6.25,1.688 6.708,1.885 0.458,0.198 10 false 12 V 0.198,1.313 1.125,1.833 0.927,0.521 10 false from BKUP LP Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))

B

2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (S Range) Transmission control switch status ON or OFF
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (S Range)
50003 373 27

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

3.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)

B

8.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
3.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sport Shift Up SW Sport shift up switch status ON or OFF
·

ON: Shift lever held in "+"

·

OFF: Shift lever not held in "+"


-
Sport Shift Down SW Sport shift down switch status ON or OFF
·

ON: Shift lever held in "-"

·

OFF: Shift lever not held in "-"


-
Powertrain > Transmission > Data List
Tester Display
Sport Shift Up SW
Sport Shift Down SW
50003 373 26,25

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

B

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C277025C46
1.875,1.781 2.01,1.385 true 2.552,1.76 2.292,1.396 true 1.26,1.76 1.729,1.385 true 2.427,1.833 2.927,2.031 0.5,0.198 10 false SFTD 1.844,1.823 2.156,2.021 0.313,0.198 10 false E 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.042,1.823 1.521,2.021 0.479,0.198 10 false SFTU
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Disconnect the K29 shift lock control unit assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SFTU) - 2 (E) Shift lever held in "+" (Up shift) Below 1 Ω
3 (SFTU) - 2 (E) Shift lever not held in "+" (Up shift) 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-" (Down shift) Below 1 Ω
1 (SFTD) - 2 (E) Shift lever not held in "-" (Down shift) 10 kΩ or higher



c.

Connect the K29 shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - BODY GROUND)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - BODY GROUND)
a.

Disconnect the K29 shift lock control unit assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K29-2 (E) - Body ground Always Below 1 Ω



c.

Connect the K29 shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - BODY GROUND)

6.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)
a.

Disconnect the C111 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C111-28 (SFTU) - Body ground Shift lever held in "+" (Up shift) Below 1 Ω
C111-28 (SFTU) - Body ground Shift lever not held in "+" (Up shift) 10 kΩ or higher
C111-27 (SFTD) - Body ground Shift lever held in "-" (Down shift) Below 1 Ω
C111-27 (SFTD) - Body ground Shift lever not held in "-" (Down shift) 10 kΩ or higher



c.

Connect the C111 TCM connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

7.REPLACE TCM
a.

Replace the TCM.

Click hereDrivetrain>K120 (CVT)>TCM>COMPONENTS


Result:
Proceed to
NEXT



NEXT

PERFORM REGISTRATION AND INITIALIZATION

8.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C12
0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.198,0.167 0.51,0.365 0.313,0.198 10 *a 1.906,1.802 2.375,2 0.469,0.198 10 IG 0.646,1.771 1.021,1.979 0.375,0.208 10 S
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the K29 shift lock control unit assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher



c.

Connect the K29 shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

9.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (POWER SOURCE)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

9.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (POWER SOURCE)
a.

Disconnect the K29 shift lock control unit assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K29-4 (IG) - Body ground Ignition switch ON 11 to 14 V
K29-4 (IG) - Body ground Ignition switch off Below 1 V



c.

Connect the K29 shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

NG

CHECK POWER SOURCE CIRCUIT (SHIFT LOCK CONTROL UNIT ASSEMBLY)

10.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)
a.

Disconnect the C111 TCM connector.


b.

Disconnect the K29 shift lock control unit assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K29-5 (S) - C111-14 (S) Always Below 1 Ω
K29-5 (S) or C111-14 (S) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the C111 TCM connector.


e.

Connect the K29 shift lock control unit assembly connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

11.REPLACE TCM
a.

Replace the TCM.

Click hereDrivetrain>K120 (CVT)>TCM>COMPONENTS


Result:
Proceed to
NEXT



NEXT

PERFORM REGISTRATION AND INITIALIZATION