Home › Engine / Hybrid System › M20A-FKS (ENGINE CONTROL) › THROTTLE BODY › from 2021.02
RM33A0E _51 Engine / Hybrid System _098626 M20A-FKS ENGINE CONTROL _0462098 THROTTLE BODY A

M20A-FKS ENGINE CONTROL  THROTTLE BODY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during throttle body with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

Hide 12601B 2.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 3.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A443491

Disconnect the mass air flow meter sub-assembly connector.


b.

Disengage the 2 wire harness clamps.


c.
A443492C01
0.458,1.49 0.563,0.969 0.563,0.969 0.75,0.969 true 0.99,3.125 0.99,2.917 0.99,2.917 1.208,2.625 true 0.917,3.135 1.167,3.313 0.25,0.177 10 true *1 0.771,0.885 1.083,1.042 0.313,0.156 10 false *2 1.635,3.104 1.875,3.323 0.24,0.219 10 true *a 1.344,0.677 1.573,0.865 0.229,0.188 10 true *b 2.719,2.865 2.958,3.083 0.24,0.219 10 true *a 1.979,0.917 2.208,1.104 0.229,0.188 10 true *b
*1 Vacuum Hose
*2 No. 2 Ventilation Hose
*a Air Cleaner Cap Clamp
*b Guide


Disconnect the vacuum hose from the air cleaner hose.


d.

Slide the clip and disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.


e.

Disengage the 2 air cleaner cap clamps.


f.

Disengage the 2 guides to separate the air cleaner cap sub-assembly from the air cleaner case sub-assembly.


g.

Loosen the hose clamp and remove the air cleaner cap with air cleaner hose from the throttle body with motor assembly.


Hide 22030 4.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

a.
A433236

Disconnect the throttle body with motor assembly connector.


b.

Slide the clip and disconnect the No. 8 water by-pass hose from the throttle body with motor assembly.


c.

Using an 8 mm socket wrench, remove the 3 bolts and disconnect the throttle body with motor assembly from the intake manifold.


d.
A433237

Slide the clip and disconnect the No. 5 water by-pass hose to remove the throttle body with motor assembly.

NOTICE:

If the throttle body with motor assembly has been struck or dropped, replace it.



Hide 22271 5.REMOVE THROTTLE BODY GASKET

a.
A433238

Remove the throttle body gasket from the intake manifold.