Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › from 2021.02
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0329531 LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System) C

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System)  B124B  Automatic High Beam System  


DESCRIPTION

The main body ECU (multiplex network body ECU) determines the status of the automatic high beam system based on the automatic high beam system signal from the forward recognition camera.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B124B Automatic High Beam System Malfunction in automatic high beam system
·

Front camera system

·

Dynamic radar cruise control system

·

Lane tracing assist system

·

Road sign assist system*

·

Front radar sensor system

·

Pre-collision system

·

SFI system

·

Vehicle stability control system

·

CAN communication system

·

Forward recognition camera

·

Main body ECU (multiplex network body ECU)


Main Body

*: w/ Road Sign Assist System


WIRING DIAGRAM

E303800E65
1.052,1.573 3.323,1.896 2.271,0.323 10 false Forward Recognition Camera 0.698,2.26 2.781,2.563 2.083,0.302 10 false : CAN Communication Line 4.729,1.563 6.375,2 1.646,0.438 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

The lighting system (w/ Automatic Headlight Beam Level Control System) uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the automatic high beam system after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*1

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*2

*1: w/ Door Control Battery

*2: w/ Smart Entry and Start System




HINT:
If the forward recognition camera stores a DTC for a malfunction of any of the following, this DTC will be stored simultaneously.
·

Speed sensor

·

Yaw rate sensor

·

Millimeter wave radar sensor

·

CAN communication system



PROCEDURE

1.CHECK FOR DTC (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check for DTCs.


Result:
Result Proceed to
Only DTC B124B is output A
DTC B124B and other DTCs are output B



A

2.CHECK FRONT CAMERA SYSTEM

B

GO TO OTHER DTC CHART

2.CHECK FRONT CAMERA SYSTEM
a.

Check if a front camera system, dynamic radar cruise control system, lane tracing assist system, road sign assist system*, front radar sensor system or pre-collision system warning message is displayed on the multi-information display.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA SYSTEM>DIAGNOSIS SYSTEM

OK:

No front camera system, dynamic radar cruise control system, lane tracing assist system, road sign assist system*, front radar sensor system or pre-collision system warning messages are displayed.


*: w/ Road Sign Assist System



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG