Home › Engine / Hybrid System › M20A-FKS (STARTING) › STARTER (for VALEO Made) › from 2021.02
RM33A0E _51 Engine / Hybrid System _098630 M20A-FKS STARTING _0462228 STARTER(for VALEO Made) G

M20A-FKS STARTING  STARTER(for VALEO Made)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.


NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a pull-in test.

i.
A452102

Remove the nut and disconnect the lead wire from terminal C.


ii.
A452099C01
0.729,0.51 0.927,0.51 0.927,0.51 1.115,0.823 false 2.938,0.25 2.667,0.25 2.667,0.25 2.49,0.563 true 2.448,0.99 3.083,2.396 3.083,2.396 2.771,2.396 true 0.521,0.406 0.833,0.604 0.313,0.198 10 false *a 3,0.177 3.313,0.375 0.313,0.198 10 false *b 2.604,2.313 2.917,2.51 0.313,0.198 10 false *c
*a Starter Body
*b Terminal 50
*c Terminal C
V100135

Moves outward


Connect a battery to the starter assembly as shown in the illustration. Check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move outward, replace the starter assembly.



b.

Perform a hold-in test.

i.
A452100C02
2.823,2.49 2.51,2.49 2.51,2.49 2.365,0.958 true 0.594,0.604 0.802,0.604 0.802,0.604 1,0.896 false 2.458,0.542 2.646,0.292 2.646,0.292 2.854,0.292 true 0.438,0.5 0.75,0.698 0.313,0.198 10 false *a 2.917,0.177 3.229,0.375 0.313,0.198 10 false *b 2.865,2.396 3.177,2.594 0.313,0.198 10 false *c
*a Starter Body
*b Terminal 50
*c Terminal C
V100135

Disconnect


While maintaining the battery connections of the pull-in test, disconnect the negative (-) lead from terminal C. Check that the clutch pinion gear does not return inward.

If the clutch pinion gear returns inward, replace the starter assembly.



c.

Perform a return test.

i.
A452101C02
0.625,0.479 0.802,0.479 0.802,0.479 1,0.896 false 2.458,0.542 2.698,0.219 2.698,0.219 2.917,0.219 true 2.406,0.938 2.635,2.5 2.635,2.5 2.875,2.5 true 0.469,0.385 0.781,0.583 0.313,0.198 10 false *a 2.979,0.115 3.292,0.313 0.313,0.198 10 false *b 2.938,2.375 3.25,2.573 0.313,0.198 10 false *c
*a Starter Body
*b Terminal 50
*c Terminal C
V100135

Disconnect
V100136

Returns Inward


Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the starter assembly.



d.

Perform a no-load performance test.

i.
A452102

Connect the lead wire to terminal C with the nut. Make sure that the lead wire is not grounded.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


ii.

Secure the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter assembly is secured in the vise to prevent it from falling out.



iii.
A452103C02
1.135,0.25 1.75,0.25 1.75,0.25 2.083,0.75 true 0.583,0.99 0.917,0.99 false 2.427,0.813 2.448,1.198 2.448,1.198 3.052,1.198 true 0.958,0.167 1.271,0.365 0.313,0.198 10 false *c 0.406,0.906 0.719,1.104 0.313,0.198 10 false *a 3.094,1.135 3.344,1.385 0.25,0.25 10 false *b
*a Starter Body
*b Terminal 50
*c Terminal 30
V100135

Rotates


Connect the battery and an ammeter to the starter assembly as shown in the illustration.

NOTICE:

Do not allow any lead to get caught as the clutch pinion gear operates.



iv.

Check that the starter assembly operates smoothly and steadily while the clutch pinion gear is moving outward.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive (+) terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A


If the result is not as specified, replace the starter assembly.



Hide 2.INSPECT STARTER DRIVE HOUSING

A452104C01
0,0 0,0 false
V100135

Free
V100136

Lock


a.

Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the starter assembly.


b.

Turn the clutch pinion gear by hand while applying inward force and check the movement of the bearing.

If resistance is felt or the bearing sticks, replace the starter assembly.