48818
1.INSTALL REAR STABILIZER BUSHING (for TMC Made)
Install the 2 rear stabilizer bushings to the rear stabilizer bar.
Be sure to install the rear stabilizer bushings so that each cutout faces the front of the vehicle.
48832A
2.INSTALL REAR NO. 1 STABILIZER BAR BRACKET (for TMC Made)
| *a | Arrow Mark |
|
Front of the Vehicle |
Install the 2 rear No. 1 stabilizer bar brackets to the 2 rear stabilizer bushings.
Be sure to install the rear No. 1 stabilizer bar brackets so that each arrow mark faces the front of the vehicle.
48812
3.INSTALL REAR STABILIZER BAR (for TMC Made)
| *a | Identification Mark |
Install the rear stabilizer bar, 2 rear No. 1 stabilizer bar brackets and 2 rear stabilizer bushings to the rear suspension member sub-assembly with the 4 bolts.
Ensure that the identification mark faces the right side of the vehicle.
Temporarily tighten the bolt (A) and then fully tighten the 2 bolts in the order of (B) and (A).
48805
4.INSTALL REAR STABILIZER BAR SUB-ASSEMBLY (for TMR Made)
| *a | Arrow Mark |
|
Front of the Vehicle |
Install the rear stabilizer bar sub-assembly to the rear suspension member sub-assembly with the 4 bolts.
Be sure to install the rear No. 1 stabilizer bar brackets so that each arrow mark faces the front of the vehicle.
Temporarily tighten bolt in the order of (A), (B), (D) and then fully tighten the 4 bolts in the order of (C), (D), (A) and (B).
5.STABILIZE SUSPENSION
48840A
6.INSTALL REAR STABILIZER LINK ASSEMBLY LH
Install the rear stabilizer link assembly LH with the nut (A).
If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.
Install the rear stabilizer link assembly LH with the bolt and nut (B).
w/ Cap:
Install the cap to the rear stabilizer link assembly LH.
48830D
7.INSTALL REAR STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
17420
8.INSTALL CENTER EXHAUST PIPE ASSEMBLY
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
58398F
9.INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)
Install the No. 1 floor under cover with the 2 grommets (B) and 2 clips (C).
Install the 2 bolts and clip (A).
58399D
10.INSTALL NO. 2 FLOOR UNDER COVER (w/ Cover)
Install the No. 2 floor under cover with the 2 grommets (B) and 2 clips (C).
Install the 2 bolts and clip (A).
11.INSTALL REAR WHEEL
12.INSPECT FOR EXHAUST GAS LEAK
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>INSTALLATION