This DTC is output when the clearance warning ECU assembly detects lost communication with the blind spot monitor sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| U117787 | Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message | The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor LH (A) | ·
Open or short in bus main line ·
Open or short in bus branch line ·
Open or short in wire harness connector (No. 5 CAN junction connector) ·
Clearance warning ECU assembly internal malfunction ·
Blind spot monitor sensor LH (A) internal malfunction ·
Blind spot monitor sensor LH (A) power source circuit malfunction ·
Blind spot monitor sensor RH (B) internal malfunction |
○ |
| U117887 | Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message | The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor RH (B) | ·
Open or short in bus main line ·
Open or short in bus branch line ·
Open or short in wire harness connector (No. 5 CAN junction connector) ·
Clearance warning ECU assembly internal malfunction ·
Blind spot monitor sensor RH (B) internal malfunction ·
Blind spot monitor sensor RH (B) power source circuit malfunction ·
Blind spot monitor sensor LH (A) internal malfunction |
○ |
Inspect the fuses for circuits related to this system before performing the following procedure.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Using the GTS, check for parking support brake system DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output | A |
| DTC U117787 only is output | B |
| DTC U117887 only is output | C |
| DTC U117787 and U117887 are output | D |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (A)) |
Disconnect the connector of the blind spot monitor sensor LH (A).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W6-10 (BLGD) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (A)) |
Disconnect the connector of the blind spot monitor sensor LH (A).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| W6-5 (BLB) - Body ground | Ignition Switch ON | 11 to 14 V |
| W6-5 (BLB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (B)) |
Disconnect the connector of the blind spot monitor sensor RH (B).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-10 (BRGD) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (B)) |
Disconnect the connector of the blind spot monitor sensor RH (B).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| W5-5 (BRB) - Body ground | Ignition switch ON | 11 to 14 V |
| W5-5 (BRB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
| *a | Component with wire harness connected
(Clearance Warning ECU Assembly) |
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Problem Symptom if Specified Condition Not Met |
|---|---|---|---|
| R39-37 (CANH) - R39-38 (CANL) | Disconnect cable from negative (-) battery terminal | 54 to 69 Ω | Below 54 Ω: Short in line |
| 70 Ω or higher: Open in main line | |||
| R39-37 (CANH) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: Short to ground |
| R39-38 (CANL) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: Short to ground |
| R39-37 (CANH) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: Short to +B |
| R39-38 (CANL) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: Short to +B |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (open in main line) | B |
| NG (short in line) | C |
| NG (short to +B or ground) | D |
A
B
C
D
Using the GTS, clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U117787 and U117887 are output | A |
| DTC U117787 and U117887 are not output | B |
A
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
B
Disconnect the No. 5 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly CAN Wire |
| *c | to Blind Spot Monitor Sensor RH (B) CAN Main Wire | *d | to Blind Spot Monitor Sensor LH (A) CAN Main Wire |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R100-1 (CANH) - R100-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R100-2 (CANH) - R100-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| R100-3 (CANH) - R100-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (A) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (B) CAN main wire) | C |
| NG (to clearance warning ECU assembly CAN wire) | D |
A
B
C
D
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (A)) |
Reconnect the R100 No. 5 CAN junction connector.
Disconnect the W6 blind spot monitor sensor LH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W6-1 (CA2P) - W6-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (B)) |
Reconnect the R100 No. 5 CAN junction connector.
Disconnect the W5 blind spot monitor sensor RH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-1 (CA2P) - W5-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Reconnect the No. 5 CAN junction connector.
Disconnect the R39 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R39-37 (CANH) - R39-38 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
NG
Disconnect the No. 5 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*b | to Clearance Warning ECU Assembly CAN Wire |
| *c | to Blind Spot Monitor Sensor RH (B) CAN Main Wire | *d | to Blind Spot Monitor Sensor LH (A) CAN Main Wire |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R100-1 (CANH) - R100-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| R100-2 (CANH) - R100-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| R100-3 (CANH) - R100-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (A) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (B) CAN main wire) | C |
| NG (to clearance warning ECU assembly CAN wire) | D |
A
B
C
D
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (A)) |
Reconnect the R100 No. 5 CAN junction connector.
Disconnect the W6 blind spot monitor sensor LH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W6-1 (CA2P) - W6-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (B)) |
Reconnect the R100 No. 5 CAN junction connector.
Disconnect the W5 blind spot monitor sensor RH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-1 (CA2P) - W5-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Reconnect the No. 5 CAN junction connector.
Disconnect the R39 clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R39-37 (CANH) - R39-38 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
NG
Disconnect the No. 5 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R100-3 (CANH) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| R100-14 (CANL) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| R100-3 (CANH) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
| R100-14 (CANL) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
Check for short that was confirmed to be a malfunction by confirming symptoms.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 5 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R100-2 (CANH) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| R100-13 (CANL) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| R100-2 (CANH) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
| R100-13 (CANL) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
Check for short that was confirmed to be a malfunction by confirming symptoms.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 5 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
*1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R100-1 (CANH) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| R100-12 (CANL) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| R100-1 (CANH) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
| R100-12 (CANL) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
Check for short that was confirmed to be a malfunction by confirming symptoms.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
| *1 | DLC3 |
Reconnect the R100 No. 5 CAN junction connector.
Disconnect the connector of the clearance warning ECU assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R39-37 (CANH) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| R39-38 (CANL) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| R39-37 (CANH) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
| R39-38 (CANL) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (B)) |
| *1 | DLC3 |
Reconnect the R100 No. 5 CAN junction connector.
Disconnect the connector of the blind spot monitor sensor RH (B).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W5-1 (CA2P) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| W5-6 (CA2N) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| W5-1 (CA2P) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
| W5-6 (CA2N) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (A)) |
| *1 | DLC3 |
Reconnect the R100 No. 5 CAN junction connector.
Disconnect the connector of the blind spot monitor sensor LH (A).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W6-1 (CA2P) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| W6-6 (CA2N) - Body ground | Disconnect cable from negative (-) battery terminal | 200 Ω or higher |
| W6-1 (CA2P) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
| W6-6 (CA2N) - K154-16 (BAT) | Disconnect cable from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG