Home › Engine / Hybrid System › M20A-FKS (FUEL) › FUEL INJECTOR (for Port Injection) › from 2021.02
RM33A0E _51 Engine / Hybrid System _098628 M20A-FKS FUEL _0462954 FUEL INJECTOR(for Port Injection) A

M20A-FKS FUEL  FUEL INJECTOR(for Port Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
·

Replacement of port fuel injector assembly

·

Replacement of No. 2 fuel pressure sensor

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 89458H 1.REMOVE NO. 2 FUEL PRESSURE SENSOR

Hide 23910A 2.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A434098

Remove the fuel pipe clamp from the fuel tube connector.


b.
A434099

Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly.

Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23807 3.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A434100

Disconnect the No. 5 engine wire connector.


b.

Remove the 2 bolts and fuel delivery pipe sub-assembly with the 4 port fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe sub-assembly.



Hide 23891 4.REMOVE FUEL DELIVERY SPACER

a.
A443071

Remove the 2 fuel delivery spacers from the cylinder head sub-assembly.


Hide 23291 5.REMOVE INJECTOR VIBRATION INSULATOR

a.
A443072

Remove the 4 injector vibration insulators from the cylinder head sub-assembly.


Hide 82125N 6.REMOVE NO. 5 ENGINE WIRE

a.
A434101

Disconnect the 4 port fuel injector assembly connectors.


b.

Disengage the 2 clamps to remove the No. 5 engine wire from the fuel delivery pipe sub-assembly.


Hide 23250F 7.REMOVE PORT FUEL INJECTOR ASSEMBLY

a.
A481888

Pull the 4 port fuel injector assemblies out of the fuel delivery pipe sub-assembly.


b.
A481889

Remove the O-ring from each port fuel injector assembly.


c.
A481890N01
2.146,0.313 2.917,0.51 0.771,0.198 10 false No. 1

Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.