Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2021.02–2022.01
RM33A0E _53 Suspension _065363 TIRE PRESSURE MONITORING _0327403 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198  Initialization Switch Error (for Test Diagnosis)  


DESCRIPTION

The switch circuit inside the combination meter assembly turns on and off according to the steering pad switch assembly operation.

During test mode, the tire pressure warning light blinks at 0.125 second intervals when "Set Pressure" is selected on the multi-information display, and illuminates when the "OK" switch (steering pad switch assembly) is pressed.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2198 Initialization Switch Error (for Test Diagnosis) Test mode procedure is performed.
·

Steering pad switch assembly

·

Spiral cable sub-assembly

·

Wire harness or connector

·

Tire pressure warning ECU and receiver


-

WIRING DIAGRAM

C397277E01
1.313,6.354 3.823,6.583 2.51,0.229 10 false *1: w/ Smart Entry and Start System 1.302,6.74 3.813,6.969 2.51,0.229 10 false *2: w/o Smart Entry and Start System 1.313,7.135 4,7.531 2.688,0.396 10 false *3: w/ No. 1 Stereo Jack Adapter Assembly (Radio and Display Receiver Type) 4.219,7 7.063,7.292 2.844,0.292 10 false *5: w/o No. 1 Stereo Jack Adapter Assembly 4.229,6.354 6.917,6.781 2.688,0.427 10 false *4: w/ No. 1 Stereo Jack Adapter Assembly (Radio Receiver Type) 4.469,1.042 7.073,1.323 2.604,0.281 10 false Tire Pressure Warning ECU and Receiver 1.406,2.135 3.396,2.427 1.99,0.292 10 false Combination Meter Assembly 4.135,0.302 4.438,0.521 0.302,0.219 10 false R9 4.448,0.302 4.896,0.51 0.448,0.208 10 false R120 4.865,0.302 5.406,0.5 0.542,0.198 10 false CLSW 4.167,0.104 4.469,0.323 0.302,0.219 10 false 3 4.552,0.094 4.854,0.313 0.302,0.219 10 false 3 4.135,0.531 4.438,0.75 0.302,0.219 10 false *1 4.531,0.521 4.833,0.74 0.302,0.219 10 false *2 2.792,0.313 3.333,0.51 0.542,0.198 10 false INT 3.167,0.177 3.469,0.396 0.302,0.219 10 false 4 1.802,0.177 2.688,0.646 0.885,0.469 10 false Tire Pressure Warning Light 1.76,0.729 2.302,0.927 0.542,0.198 10 false ES 1.76,1.302 2.302,1.5 0.542,0.198 10 false MSTI 1.813,1.708 2.354,1.906 0.542,0.198 10 false MSM+ 1.406,1.979 1.948,2.177 0.542,0.198 10 false K21 1.448,0.604 1.75,0.823 0.302,0.219 10 false 21 1.448,1.156 1.75,1.375 0.302,0.219 10 false 29 1.448,1.583 1.75,1.802 0.302,0.219 10 false 28 3.813,2.375 4.354,2.573 0.542,0.198 10 false +DP2 3.823,2.781 4.365,2.979 0.542,0.198 10 false +DP 3.854,3.177 4.396,3.375 0.542,0.198 10 false EAU 3.469,2.479 4.01,2.677 0.542,0.198 10 false K22 3.469,2.875 4.01,3.073 0.542,0.198 10 false K22 3.479,3.271 4.021,3.469 0.542,0.198 10 false K22 4.906,2.479 5.448,2.677 0.542,0.198 10 false z1 4.917,2.885 5.458,3.083 0.542,0.198 10 false z1 4.917,3.26 5.458,3.458 0.542,0.198 10 false z1 3.49,2.281 3.844,2.469 0.354,0.188 10 false 10 3.5,2.688 3.854,2.875 0.354,0.188 10 false 11 3.542,3.083 3.771,3.281 0.229,0.198 10 false 4 4.927,2.688 5.156,2.885 0.229,0.198 10 false 4 4.927,2.292 5.156,2.49 0.229,0.198 10 false 5 4.896,3.094 5.25,3.281 0.354,0.188 10 false 10 3.167,3.625 5.146,3.896 1.979,0.271 10 false Spiral Cable Sub-assembly 5.125,3.615 7.135,3.906 2.01,0.292 10 false Steering Pad Switch Assembly 1.073,4.688 1.396,4.875 0.323,0.188 10 false K3 1.063,4.844 3.656,5.063 2.594,0.219 10 false Radio and Display Receiver Assembly*3 1.104,5.458 1.531,5.646 0.427,0.188 10 false K144 2.896,5.458 3.375,5.677 0.479,0.219 10 false K152 1.219,4.229 1.573,4.417 0.354,0.188 10 false 24 2.948,4.229 3.302,4.417 0.354,0.188 10 false 1 1.167,5.25 1.521,5.438 0.354,0.188 10 false 23 3.01,5.25 3.365,5.438 0.354,0.188 10 false 7 1.51,4.323 2.052,4.521 0.542,0.198 10 false SWG 1.49,5.448 2.031,5.646 0.542,0.198 10 false SWG 2.427,5.438 2.969,5.635 0.542,0.198 10 false GND1 2.438,4.333 2.979,4.531 0.542,0.198 10 false GND1 1.333,5.865 3.208,6.104 1.875,0.24 10 false Radio Receiver Assembly*4 0.521,5.729 0.75,5.917 0.229,0.188 10 false *5 0.729,5.344 0.958,5.531 0.229,0.188 10 false *4 3.448,5.344 3.677,5.531 0.229,0.188 10 false *4 3.448,4.219 3.677,4.406 0.229,0.188 10 false *3 0.708,4.219 0.938,4.406 0.229,0.188 10 false *3

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the K22 spiral cable sub-assembly connector.


b.

Disconnect the K21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-10 (+DP2) - K21-28 (MSM+) Always Below 1 Ω
K22-10 (+DP2) or K21-28 (MSM+) - Body ground Always 10 kΩ or higher
K22-11 (+DP) - K21-29 (MSTI) Always Below 1 Ω
K22-11 (+DP) or K21-29 (MSTI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the R9 or R120 tire pressure warning ECU and receiver connector.


b.

Disconnect the K21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Smart Entry and Start System
Tester Connection Condition Specified Condition
R9-3 (CLSW) - K21-4 (INT) Always Below 1 Ω
R9-3 (CLSW) or K21-4 (INT) - Body ground Always 10 kΩ or higher
K21-21 (ES) - Body ground Always Below 1 Ω

w/o Smart Entry and Start System
Tester Connection Condition Specified Condition
R120-3 (CLSW) - K21-4 (INT) Always Below 1 Ω
R120-3 (CLSW) or K21-4 (INT) - Body ground Always 10 kΩ or higher
K21-21 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (INT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (INT)
a.

Connect the R9 or R120 tire pressure warning ECU and receiver connector.


b.

Disconnect the K21 combination meter assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K21-4 (INT) - Body ground Ignition switch ON 8 to 15 V


Result:
Proceed to
OK
NG




OK

NG

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER