Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>PRECAUTION
Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.
Do not reuse parts which have reduced fastening ability due to thread damage.
Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
When installing components, make sure that the wire harness is not pinched or pulled.
Do not use solvent to clean components. Only clean them with a dry cloth.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
81056A
1.REMOVE HEADLIGHT ECU SUB-ASSEMBLY (w/ Automatic Headlight Beam Level Control System)
81134
2.REMOVE HEADLIGHT GASKET (w/ Automatic Headlight Beam Level Control System)
81510C
3.REMOVE FRONT TURN SIGNAL LIGHT BULB
w/ Automatic Headlight Beam Level Control System:
|
Disconnect in this Direction |
Turn the headlight cord with the front turn signal light bulb as shown in the illustration to disconnect them as a unit.
Remove the front turn signal light bulb from the headlight cord.
w/o Automatic Headlight Beam Level Control System:
|
Disconnect in this Direction |
Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to remove them as a unit.
Remove the front turn signal light bulb from the front turn signal light socket.
81515B
4.REMOVE FRONT TURN SIGNAL LIGHT SOCKET (w/o Automatic Headlight Beam Level Control System)
81171B
5.REMOVE HEADLIGHT LENS
Make sure to wear clean rubber gloves when performing this procedure.
Do not allow dirt or foreign matter to get on the headlight lens.
Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.
Do not use solvent to clean components. Only clean them with a dry cloth.
Remove the 8 screws.
Using a hair dryer, heat the backside of the headlight assembly.
If the headlight assembly is heated unevenly, it will deform or melt.
Disengage the 9 claws.
Remove the headlight lens from the headlight housing sub-assembly.
If the headlight lens cannot be removed even after heating, using a screwdriver with its tip wrapped with protective tape, lift the headlight lens. Be careful not to damage the headlight lens and headlight housing sub-assembly.
81132B
6.REMOVE HEADLIGHT LENS GASKET
The headlight lens gasket must not be reused.
Make sure to wear clean rubber gloves when performing this procedure.
Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.
Do not use solvent to clean components. Only clean them with a dry cloth.
Remove the headlight lens gasket from the headlight housing sub-assembly.
Make sure to replace the headlight lens gasket with a new one. Failure to do so may cause water ingress.
81169
7.REMOVE HEADLIGHT REFLECTOR
Make sure to wear clean rubber gloves when performing this procedure.
Do not allow dirt or foreign matter to get on the headlight reflector or other components.
Do not touch the headlight reflector with bare hands.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
If there are any fingerprints or foreign matter on the headlight reflector or other components, wipe them off with a soft cloth.
Do not use solvent to clean components. Only clean them with a dry cloth.
|
Remove in this Direction |
Remove the screw.
Disengage the 2 guides to remove the headlight reflector as shown in the illustration.
8116A
8.REMOVE NO. 1 HEADLIGHT CLEARANCE LED UNIT
Make sure to wear clean rubber gloves when performing this procedure.
Do not allow dirt or foreign matter to get on the No. 1 headlight clearance LED unit or other components.
Prevention of static electricity is required during this procedure.
Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).
Do not touch the No. 1 headlight clearance LED unit with bare hands.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
If there are any fingerprints or foreign matter on the No. 1 headlight clearance LED unit or other components, wipe them off with a soft cloth.
Do not use solvent to clean components. Only clean them with a dry cloth.
Disconnect the 2 connectors.
Disengage the 2 clamps.
|
Remove in this Direction |
Remove the 2 screws.
Disengage the guide to remove the No. 1 headlight clearance LED unit as shown in the illustration.
81160A
9.REMOVE HEADLIGHT LED UNIT ASSEMBLY
Make sure to wear clean rubber gloves when performing this procedure.
Do not allow dirt or foreign matter to get on the headlight LED unit assembly or other components.
Prevention of static electricity is required during this procedure.
Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).
Do not touch the headlight LED unit assembly with bare hands.
Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.
If there are any fingerprints or foreign matter on the headlight LED unit assembly or other components, wipe them off with a soft cloth.
Do not use solvent to clean components. Only clean them with a dry cloth.
Disengage the 5 clamps.
Disconnect the connector.
Disengage the pivot collar.
| *A | w/o Automatic Headlight Beam Level Control System | *B | w/ Automatic Headlight Beam Level Control System |
|
Turn in this Direction |
While holding the headlight LED unit assembly by hand, turn the aiming screws as shown in the illustration until the aiming screws are disconnected from the headlight LED unit assembly.
Make sure to remember the number of aiming screw rotations.
Disengage the 2 clamps.
Disconnect the connector to remove the headlight LED unit assembly from the headlight housing sub-assembly.
85967
10.REMOVE LIGHT CONTROL ECU (w/o Automatic Headlight Beam Level Control System)
Disconnect the connector.
Remove the 2 screws and light control ECU.
81102
11.REMOVE HEADLIGHT HOUSING SUB-ASSEMBLY (w/ Automatic Headlight Beam Level Control System)
As the headlight housing sub-assembly is available as a supply part, proceed to the next step if it is necessary to change the headlight housing sub-assembly.
|
Disengage in this Direction |
Disengage the grommet as shown in the illustration.
Disengage the 2 clamps.
Disconnect the connector.
Disengage the 3 clamps to remove the headlight cord from the headlight housing sub-assembly.
Remove the 3 screws.
Disengage the guide to remove the headlight leveling motor from the headlight housing sub-assembly.
Remove the 2 screws and bracket C from the headlight housing sub-assembly.
Remove the 2 screws and bracket D from the headlight housing sub-assembly.
81102
12.REMOVE HEADLIGHT HOUSING SUB-ASSEMBLY (w/o Automatic Headlight Beam Level Control System)
As the headlight housing sub-assembly is available as a supply part, proceed to the next step if it is necessary to change the headlight housing sub-assembly.
Disengage the claw.
|
Disengage in this Direction |
Disengage the grommet as shown in the illustration.
Disengage the 2 clamps to remove the headlight cord from the headlight housing sub-assembly.
Remove the 2 screws and bracket C from the headlight housing sub-assembly.
Remove the 2 screws and bracket D from the headlight housing sub-assembly.