81175
1.INSPECT HEADLIGHT UNIT ASSEMBLY LH (w/ Automatic Headlight Beam Level Control System)
| *1 | Headlight Unit Assembly LH (Headlight Cord) | - | - |
| *a | Component without harness connected
(to Headlight ECU Sub-assembly LH) |
*b | Component without harness connected
(to Headlight LED Unit Assembly LH) |
| *c | Component without harness connected
(to Headlight Leveling Motor LH) |
*d | Component without harness connected
(to No. 1 Headlight Clearance LED Unit LH) |
| *e | Component without turn signal light installed
(to Turn Signal Light) |
- | - |
Measure the resistance according to the value(s) in the table below.
Inspect the headlight leveling motor circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-7 (ACTBI) - E-1 | Always | Below 1 Ω |
| B-8 (ACTSI) - E-2 | Always | Below 1 Ω |
| B-17 (ACTGI) - E-3 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the Lo/Hi beam circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-4 (LOLED2) - D-2 | Always | Below 1 Ω |
| B-3 (LOLED0) - D-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the Lo/Hi beam shade circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-20 (HI_SOL+) - C-2 | Always | Below 1 Ω |
| B-11 (HI_SOL-) - C-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the clearance light/daytime running light input circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-10 (DRL/CLL+) - F-1 | Always | Below 1 Ω |
| B-1 (DRL/CLL-) - F-3 | Always | Below 1 Ω |
| B-19 (CLL+) - F-2 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the clearance light/daytime running light output circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F-4 - G-5 | Always | Below 1 Ω |
| F-5 - G-4 | Always | Below 1 Ω |
| F-6 - G-3 | Always | Below 1 Ω |
| F-7 - G-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
81160A
2.INSPECT HEADLIGHT LED UNIT ASSEMBLY LH (w/ Automatic Headlight Beam Level Control System)
| *a | Component without harness connected
(Headlight LED Unit Assembly LH) |
Apply battery voltage to the headlight LED unit assembly LH and check that the Lo/Hi beam shade operates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2 |
Operates normally |
If the result is not as specified, replace the headlight LED unit assembly LH.
8116A
3.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT LH (w/ Automatic Headlight Beam Level Control System)
| *a | Component without harness connected
(No. 1 Headlight Clearance LED Unit LH) |
Apply battery voltage to the No. 1 headlight clearance LED unit LH and check that the light illuminates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 3 |
Clearance light/daytime running light illuminates |
If the result is not as specified, replace the No. 1 headlight clearance LED unit LH.
81135
4.INSPECT HEADLIGHT UNIT ASSEMBLY RH (w/ Automatic Headlight Beam Level Control System)
| *1 | Headlight Unit Assembly RH (Headlight Cord) | - | - |
| *a | Component without harness connected
(to Headlight ECU Sub-assembly RH) |
*b | Component without harness connected
(to Headlight LED Unit Assembly RH) |
| *c | Component without harness connected
(to Headlight Leveling Motor RH) |
*d | Component without harness connected
(to No. 1 Headlight Clearance LED Unit RH) |
| *e | Component without turn signal light installed
(to Turn Signal Light) |
- | - |
Measure the resistance according to the value(s) in the table below.
Inspect the headlight leveling motor circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-7 (ACTBI) - E-1 | Always | Below 1 Ω |
| B-8 (ACTSI) - E-2 | Always | Below 1 Ω |
| B-17 (ACTGI) - E-3 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the Lo/Hi beam circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-4 (LOLED2) - D-2 | Always | Below 1 Ω |
| B-3 (LOLED0) - D-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the Lo/Hi beam shade circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-20 (HI_SOL+) - C-2 | Always | Below 1 Ω |
| B-11 (HI_SOL-) - C-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the clearance light/daytime running light input circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-10 (DRL/CLL+) - F-1 | Always | Below 1 Ω |
| B-1 (DRL/CLL-) - F-3 | Always | Below 1 Ω |
| B-19 (CLL+) - F-2 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the clearance light/daytime running light output circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F-4 - G-5 | Always | Below 1 Ω |
| F-5 - G-4 | Always | Below 1 Ω |
| F-6 - G-3 | Always | Below 1 Ω |
| F-7 - G-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
81140
5.INSPECT HEADLIGHT LED UNIT ASSEMBLY RH (w/ Automatic Headlight Beam Level Control System)
| *a | Component without harness connected
(Headlight LED Unit Assembly RH) |
Apply battery voltage to the headlight LED unit assembly RH and check that the Lo/Hi beam shade operates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2 |
Operates normally |
If the result is not as specified, replace the headlight LED unit assembly RH.
8112A
6.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT RH (w/ Automatic Headlight Beam Level Control System)
| *a | Component without harness connected
(No. 1 Headlight Clearance LED Unit RH) |
Apply battery voltage to the No. 1 headlight clearance LED unit RH and check that the light illuminates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 3 |
Clearance light/daytime running light illuminates |
If the result is not as specified, replace the No. 1 headlight clearance LED unit RH.
81175
7.INSPECT HEADLIGHT UNIT ASSEMBLY LH (w/o Automatic Headlight Beam Level Control System)
| *1 | Headlight Unit Assembly LH (Headlight Cord) | - | - |
| *a | Component without harness connected
(to Wire Harness) |
*b | Component without harness connected
(to Headlight LED Unit Assembly LH) |
| *c | Component without harness connected
(to Light Control ECU) |
*d | Component without harness connected
(to No. 1 Headlight Clearance LED Unit LH) |
Measure the resistance according to the value(s) in the table below.
Inspect the Lo/Hi beam circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A74-1 (E) - B-6 | Always | Below 1 Ω |
| A74-2 (S) - B-12 | Always | Below 1 Ω |
| A74-3 (LO) - B-7 | Always | Below 1 Ω |
| B-4 - C-1 | Always | Below 1 Ω |
| B-10 - C-2 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the Lo/Hi beam shade circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A74-1 (E) - D-2 | Always | Below 1 Ω |
| A74-4 (SOL) - D-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the clearance light/daytime running light input circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A74-1 (E) - E-3 | Always | Below 1 Ω |
| A74-5 (B) - E-2 | Always | Below 1 Ω |
| A74-6 (B) - E-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
Inspect the clearance light/daytime running light output circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-4 - F-5 | Always | Below 1 Ω |
| E-5 - F-4 | Always | Below 1 Ω |
| E-6 - F-3 | Always | Below 1 Ω |
| E-7 - F-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly LH (headlight cord).
81160A
8.INSPECT HEADLIGHT LED UNIT ASSEMBLY LH (w/o Automatic Headlight Beam Level Control System)
| *a | Component without harness connected
(Headlight LED Unit Assembly LH) |
Apply battery voltage to the headlight LED unit assembly LH and check that the Lo/Hi beam shade operates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2 |
Operates normally |
If the result is not as specified, replace the headlight LED unit assembly LH.
8116A
9.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT LH (w/o Automatic Headlight Beam Level Control System)
| *a | Component without harness connected
(No. 1 Headlight Clearance LED Unit LH) |
Apply battery voltage to the No. 1 headlight clearance LED unit LH and check that the light illuminates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 3 |
Clearance light/daytime running light illuminates |
If the result is not as specified, replace the No. 1 headlight clearance LED unit LH.
81135
10.INSPECT HEADLIGHT UNIT ASSEMBLY RH (w/o Automatic Headlight Beam Level Control System)
| *1 | Headlight Unit Assembly RH (Headlight Cord) | - | - |
| *a | Component without harness connected
(to Wire Harness) |
*b | Component without harness connected
(to Headlight LED Unit Assembly RH) |
| *c | Component without harness connected
(to Light Control ECU) |
*d | Component without harness connected
(to No. 1 Headlight Clearance LED Unit RH) |
Measure the resistance according to the value(s) in the table below.
Inspect the Lo/Hi beam circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A73-1 (E) - B-6 | Always | Below 1 Ω |
| A73-2 (S) - B-12 | Always | Below 1 Ω |
| A73-3 (LO) - B-7 | Always | Below 1 Ω |
| B-4 - C-1 | Always | Below 1 Ω |
| B-10 - C-2 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the Lo/Hi beam shade circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A73-1 (E) - D-2 | Always | Below 1 Ω |
| A73-4 (SOL) - D-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the clearance light/daytime running light input circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A73-1 (E) - E-3 | Always | Below 1 Ω |
| A73-5 (B) - E-2 | Always | Below 1 Ω |
| A73-6 (B) - E-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
Inspect the clearance light/daytime running light output circuit.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E-4 - F-5 | Always | Below 1 Ω |
| E-5 - F-4 | Always | Below 1 Ω |
| E-6 - F-3 | Always | Below 1 Ω |
| E-7 - F-1 | Always | Below 1 Ω |
If the result is not as specified, replace the headlight unit assembly RH (headlight cord).
81140
11.INSPECT HEADLIGHT LED UNIT ASSEMBLY RH (w/o Automatic Headlight Beam Level Control System)
| *a | Component without harness connected
(Headlight LED Unit Assembly RH) |
Apply battery voltage to the headlight LED unit assembly RH and check that the Lo/Hi beam shade operates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2 |
Operates normally |
If the result is not as specified, replace the headlight LED unit assembly RH.
8112A
12.INSPECT NO. 1 HEADLIGHT CLEARANCE LED UNIT RH (w/o Automatic Headlight Beam Level Control System)
| *a | Component without harness connected
(No. 1 Headlight Clearance LED Unit RH) |
Apply battery voltage to the No. 1 headlight clearance LED unit RH and check that the light illuminates.
| Condition | Specified Condition |
|---|---|
| Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 3 |
Clearance light/daytime running light illuminates |
If the result is not as specified, replace the No. 1 headlight clearance LED unit RH.