Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0351447 PANORAMIC VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  TERMINALS OF ECU  


TELEVISION CAMERA CONTROLLER


E432063N14
2.76,0.198 3.271,0.438 0.51,0.24 4.771,0.208 5.281,0.448 0.51,0.24 2.844,0.229 3.458,0.427 0.615,0.198 10 false R126 4.844,0.24 5.458,0.438 0.615,0.198 10 false R125

a.

Disconnect the R125 television camera controller connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
R125-1 (+B) - R125-4 (GND1) Power source signal Ignition switch off 11 to 14 V
R125-2 (ACC) - R125-4 (GND1) ACC power source signal Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
R125-3 (IG) - R125-4 (GND1) IG power source signal Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
R125-4 (GND1) - Body ground Ground Always Below 1 Ω


c.

Reconnect the R125 television camera controller connector.


d.

Measure the voltage, resistance and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
R126-6 (RSW+) - R125-4 (GND1) Terminal required by law Panoramic image being displayed 0 to 2 V
Panoramic image not being displayed 5.5 to 7.05 V
R126-7 (NS+) - R126-24 (NS-) Video signal Ignition switch ON and panoramic image being displayed Pulse generation (See waveform 3)
R126-8 (NSG) - Body ground Shield ground Always Below 1 Ω
R126-10 (LCV+) - R126-35 (LGND) Side television camera assembly LH display signal input Ignition switch ON with the camera lens of the side television camera assembly LH not covered, displaying the panoramic image Pulse generation (See waveform 1)
Ignition switch ON with the camera lens of the side television camera assembly LH covered, blacking out the panoramic image Pulse generation (See waveform 2)
R126-11 (SGND) - Body ground Shielded - Body ground Always Below 1 Ω
R126-12 (LCB+) - R126-35 (LGND) Power source to side television camera assembly LH Ignition switch ON 5.5 to 7.05 V
R126-13 (BCV-) - R125-4 (GND1) Front television camera assembly ground Always Below 1 Ω
R126-14 (SGND) - Body ground Shielded - Body ground Always Below 1 Ω
R126-15 (BCB+) - R126-37 (BGND) Power source to front television camera assembly Ignition switch ON 5.5 to 7.05 V
R126-16 (RCV-) - R126-17 (RGND) Side television camera assembly RH ground Always Below 1 Ω
R126-17 (RGND) - Body ground Side television camera assembly RH ground Always Below 1 Ω
R126-24 (NS-) - R125-4 (GND1) Ground Always Below 1 Ω
R126-29 (CV+) - R126-32 (CGND) Rear television camera assembly display signal input Ignition switch ON with the camera lens of the rear television camera assembly not covered, displaying the panoramic image Pulse generation (See waveform 1)
Ignition switch ON with the camera lens of the rear television camera assembly covered, blacking out the panoramic image Pulse generation (See waveform 2)
R126-30 (CV-) - R126-32 (CGND) Rear television camera assembly ground Always Below 1 Ω
R126-32 (CGND) - Body ground Rear television camera assembly ground (shield) Always Below 1 Ω
R126-34 (LCV-) - R126-35 (LGND) Side television camera assembly LH ground Always Below 1 Ω
R126-35 (LGND) - Body ground Side television camera assembly LH ground Always Below 1 Ω
R126-36 (BCV+) - R126-37 (BGND) Front television camera assembly display signal input Ignition switch ON with the camera lens of the front television camera assembly not covered, displaying the panoramic image Pulse generation (See waveform 1)
Ignition switch ON with the camera lens of the front television camera assembly covered, blacking out the panoramic image Pulse generation (See waveform 2)
R126-37 (BGND) - Body ground Front television camera assembly ground Always Below 1 Ω
R126-38 (RCV+) - R126-17 (RGND) Side television camera assembly RH display signal input Ignition switch ON with the camera lens of the side television camera assembly RH not covered, displaying the panoramic image Pulse generation (See waveform 1)
Ignition switch ON with the camera lens of the side television camera assembly RH covered, blacking out the panoramic image Pulse generation (See waveform 2)
R126-39 (SGND) - Body ground Shielded - Body ground Always Below 1 Ω
R126-40 (RCB+) - R126-17 (RGND) Power source to side television camera assembly RH Ignition switch ON 5.5 to 7.05 V
R125-15 (BLSW) - R125-4 (GND1) Panoramic view monitor switch signal Ignition switch ON, panoramic view monitor switch not pushed 5.5 to 6.5 V
Ignition switch ON, panoramic view monitor switch pushed Below 1 V
R125-11 (CANH) CAN communication line - -
R125-12 (CANL) CAN communication line - -


e.
E265840C04
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly, front television camera assembly, side television camera assembly LH and side television camera assembly RH. Therefore, inspect the waveform at the television camera controller with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal
·

R126-29 (CV+) - R126-32 (CGND)

·

R126-10 (LCV+) - R126-35 (LGND)

·

R126-36 (BCV+) - R126-37 (BGND)

·

R126-38 (RCV+) - R126-17 (RGND)


Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic view monitor system operating

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly, front television camera assembly, side television camera assembly LH or side television camera assembly RH.

·

The video waveform is constantly output when the ignition switch is turned to ACC.




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal
·

R126-29 (CV+) - R126-32 (CGND)

·

R126-10 (LCV+) - R126-35 (LGND)

·

R126-36 (BCV+) - R126-37 (BGND)

·

R126-38 (RCV+) - R126-17 (RGND)


Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic view monitor system operating

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly, front television camera assembly, side television camera assembly LH or side television camera assembly RH.

·

The video waveform is constantly output when the ignition switch is turned to ACC.




iii.
E336160C01
1.115,2.26 1.01,2.833 1.01,2.833 0.896,2.833 false 1.25,2.135 1.406,2.854 1.406,2.854 1.583,2.854 false 0.229,0.313 0.542,0.51 0.313,0.198 10 false *a 0.271,1.594 0.688,1.792 0.417,0.198 10 false GND 1.625,2.771 1.938,2.969 0.313,0.198 10 false *c 0.698,2.74 1.01,2.938 0.313,0.198 10 false *b
*a Waveform 3 (camera lens is not covered, displaying an image)
*b Synchronization Signal
*c Video Waveform


Waveform 3

Item Content
Measurement terminal R126-7 (NS+) - R126-24 (NS-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic image being displayed

HINT:

The video waveform changes according to the image sent by the television camera controller.





REAR TELEVISION CAMERA ASSEMBLY


E286120N47
3.292,0.094 3.813,0.344 0.521,0.25 3.438,0.135 3.844,0.333 0.406,0.198 10 false m4

a.

Disconnect the m4 rear television camera assembly connector.


b.

Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Switch Condition Specified Condition
m4-6 (CB+) - Body ground Power source Ignition switch ACC 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the m4 rear television camera assembly connector.


d.

Measure the resistance and check for pulses at each terminal of the connector.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
m4-3 (CV+) - m4-2 (CV-) Video signal Ignition switch ON
Shift position in R
Camera lens not covered, displaying image
Pulse generation
(Refer to waveform 1)
Ignition switch ON
Shift position in R
Camera lens covered, blacking out screen
Pulse generation
(Refer to waveform 2)
m4-5 (CGND) - Body ground Camera ground Always Below 1 V

If the result is not as specified, the rear television camera assembly may be malfunctioning.


e.
E265840C04
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens not covered, displaying image)
*b Waveform 2 (camera lens covered, blacking out screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal m4-3 (CV+) - m4-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift position in R, camera lens not covered, displaying image

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal m4-3 (CV+) - m4-2 (CV-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift position in R, camera lens covered, blacking out screen

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.