When an incorrect ECM, main body ECU (multiplex network body ECU) or skid control ECU (brake actuator assembly) is installed after the assist map has been written to the power steering ECU (rack and pinion power steering gear assembly), DTC C1582 is stored because the information stored in the power steering ECU (rack and pinion power steering gear assembly) does not match the vehicle specifications.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Return-to-normal Condition | Note |
|---|---|---|---|---|---|---|
| C1582 | Assist Map Number Mismatch | Assist map number mismatch | ·
CAN communication system ·
Incorrect ECM ·
Incorrect main body ECU (multiplex network body ECU) ·
Incorrect skid control ECU (brake actuator assembly) ·
Rack and pinion power steering gear assembly |
EPS warning light: Does not come on | Ignition switch is turned to ON again | - |
If the rack and pinion power steering gear assembly has been replaced, perform assist map writing and torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
Related parts store information necessary for assist map writing.
Related Part:
ECM
Main body ECU (Multiplex network body ECU)
Skid control ECU (Brake actuator assembly)
Check for DTCs.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output. | A |
| CAN communication system DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the part below has been replaced with an incorrect part in the past.
| Related Part | ECM |
| Main body ECU (Multiplex network body ECU) | |
| Skid control ECU (Brake actuator assembly) |
When removing the related part to check it, be sure to follow the appropriate procedures and precautions.
ECM
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL
Main body ECU (Multiplex network body ECU)
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Skid control ECU (Brake actuator assembly)
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
When DTC C1582 is output and parts have not been exchanged, replace the power steering ECU (rack and pinion power steering gear assembly) as it may have an internal malfunction.
If the rack and pinion power steering gear assembly has been replaced, perform assist map writing.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
| Result | Proceed to |
|---|---|
| The related part has an incorrect part number. | A |
| The related part has the correct part number, or a related part and rack and pinion power steering gear assembly have not been replaced. | B |
A
B
Replace the related part with one that has the correct part number.
ECM
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL
Main body ECU (Multiplex network body ECU)
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Skid control ECU (Brake actuator assembly)
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B