Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0463553 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light switch assembly signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake pedal is depressed, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels control of vehicle speed by the cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch is ON and the cruise control system is operating, the voltage of the STP and ST1- terminals of the ECM are less than 1 V for 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

ECM



WIRING DIAGRAM

for A25A-FKS:
A460859E10
0.646,0.708 2.635,0.906 1.99,0.198 10 false from Battery 0.115,1.208 2.104,1.406 1.99,0.198 10 false from IG2-NO. 2 Relay 2.396,0.896 4.385,1.094 1.99,0.198 10 false STOP 2.146,1.406 4.135,1.604 1.99,0.198 10 false ECU-IG2 NO. 3 3.042,2.135 5.031,2.333 1.99,0.198 10 false Stop Light Switch Assembly 2.677,2.135 4.667,2.333 1.99,0.198 10 false A85 3.573,0.74 3.729,0.938 0.156,0.198 10 false B 3.573,1.219 3.729,1.417 0.156,0.198 10 false B 3.552,1.74 4.01,1.938 0.458,0.198 10 false GND 4.156,0.604 4.313,0.802 0.156,0.198 10 false L 4.167,1.385 4.323,1.583 0.156,0.198 10 false L 3.333,0.625 4,0.865 0.667,0.24 10 false 7 3.333,1.115 4.198,1.406 0.865,0.292 10 false 6 3.354,1.625 3.948,1.885 0.594,0.26 10 false 2 4.344,0.5 4.948,0.729 0.604,0.229 10 false 3 4.344,1.302 4.948,1.51 0.604,0.208 10 false 5 5.688,0.5 6.146,0.698 0.458,0.198 10 false STP 5.677,1.292 6.135,1.49 0.458,0.198 10 false ST1- 5.438,0.51 6.229,0.74 0.792,0.229 10 false 21 5.438,1.302 6.313,1.531 0.875,0.229 10 false 22 6.052,2.146 6.51,2.344 0.458,0.198 10 false ECM 5.729,2.146 6.646,2.365 0.917,0.219 10 false A24 2.135,3.229 4.948,3.438 2.813,0.208 10 false Skid Control ECU (Brake Actuator Assembly) 2.167,3.01 4.156,3.208 1.99,0.198 10 false A34 3.948,2.865 4.406,3.063 0.458,0.198 10 false STP 4.354,2.75 4.729,2.969 0.375,0.219 10 false 42 5.5,2.75 5.708,2.958 0.208,0.208 10 false 25 5.313,3.25 6.833,3.635 1.521,0.385 10 false Certification ECU (Smart Key ECU Assembly)*2 5.75,2.865 6.292,3.052 0.542,0.188 10 false STP1*2 5.042,3.25 5.25,3.458 0.208,0.208 10 false R8 3.073,4.271 4.854,4.625 1.781,0.354 10 false Shift Lock Control ECU (Shift Lock Control Unit Assembly) 2.604,4.063 4.594,4.26 1.99,0.198 10 false K28*1, K27*2 4.354,3.781 4.896,3.969 0.542,0.188 10 false 8*1, 4*2 3.979,3.906 4.438,4.104 0.458,0.198 10 false STP 0.094,3.635 2.656,3.865 2.563,0.229 10 false *1: w/o Smart Entry and Start System 0.094,4.052 2.635,4.292 2.542,0.24 10 false *2: w/ Smart Entry and Start System

for 2GR-FKS:
A460859E11
0.656,0.708 2.646,0.906 1.99,0.198 10 false from Battery 0.115,1.208 2.104,1.406 1.99,0.198 10 false from IG2-NO. 2 Relay 2.396,0.896 4.385,1.094 1.99,0.198 10 false STOP 2.146,1.406 4.135,1.604 1.99,0.198 10 false ECU-IG2 NO. 3 3.042,2.135 5.031,2.333 1.99,0.198 10 false Stop Light Switch Assembly 2.708,2.135 4.698,2.333 1.99,0.198 10 false A85 3.573,0.74 3.729,0.938 0.156,0.198 10 false B 3.573,1.219 3.729,1.417 0.156,0.198 10 false B 3.552,1.74 4.01,1.938 0.458,0.198 10 false GND 4.156,0.604 4.313,0.802 0.156,0.198 10 false L 4.167,1.385 4.323,1.583 0.156,0.198 10 false L 3.417,0.625 4.083,0.865 0.667,0.24 10 false 7 3.406,1.125 4.271,1.417 0.865,0.292 10 false 6 3.396,1.625 3.99,1.885 0.594,0.26 10 false 2 4.344,0.5 4.948,0.729 0.604,0.229 10 false 3 4.344,1.302 4.948,1.51 0.604,0.208 10 false 5 5.688,0.5 6.146,0.698 0.458,0.198 10 false STP 5.677,1.292 6.135,1.49 0.458,0.198 10 false ST1- 5.427,0.521 6.219,0.75 0.792,0.229 10 false 27 5.427,1.313 6.302,1.542 0.875,0.229 10 false 42 6.052,2.146 6.51,2.344 0.458,0.198 10 false ECM 5.719,2.146 6.635,2.365 0.917,0.219 10 false A23 2.135,3.229 4.948,3.438 2.813,0.208 10 false Skid Control ECU (Brake Actuator Assembly) 1.844,3.229 3.833,3.427 1.99,0.198 10 false A34 3.948,2.865 4.406,3.063 0.458,0.198 10 false STP 4.344,2.771 4.708,3.177 0.365,0.406 10 false 42 5.5,2.75 5.708,2.958 0.208,0.208 10 false 25 5.406,3.25 6.927,3.635 1.521,0.385 10 false Certification ECU (Smart Key ECU Assembly) 5.75,2.865 6.292,3.052 0.542,0.188 10 false STP1 5.188,3.25 5.396,3.458 0.208,0.208 10 false R8 3.073,4.271 4.854,4.625 1.781,0.354 10 false Shift Lock Control ECU (Shift Lock Control Unit Assembly) 2.792,4.26 4.781,4.458 1.99,0.198 10 false K27 4.354,3.781 4.896,3.969 0.542,0.188 10 false 4 3.979,3.906 4.438,4.104 0.458,0.198 10 false STP

for M20A-FKS:
B606113E01
0.635,0.708 2.625,0.906 1.99,0.198 10 false from Battery 0.115,1.208 2.104,1.406 1.99,0.198 10 false from IG2-NO. 2 Relay 2.396,0.896 4.385,1.094 1.99,0.198 10 false STOP 2.146,1.406 4.135,1.604 1.99,0.198 10 false ECU-IG2 NO. 3 3.042,2.135 5.031,2.333 1.99,0.198 10 false Stop Light Switch Assembly 2.677,2.135 4.667,2.333 1.99,0.198 10 false A85 3.573,0.74 3.729,0.938 0.156,0.198 10 false B 3.573,1.219 3.729,1.417 0.156,0.198 10 false B 3.552,1.74 4.01,1.938 0.458,0.198 10 false GND 4.156,0.604 4.313,0.802 0.156,0.198 10 false L 4.167,1.385 4.323,1.583 0.156,0.198 10 false L 3.333,0.625 4,0.865 0.667,0.24 10 false 7 3.333,1.115 4.198,1.406 0.865,0.292 10 false 6 3.354,1.625 3.948,1.885 0.594,0.26 10 false 2 4.344,0.5 4.948,0.729 0.604,0.229 10 false 3 4.344,1.302 4.948,1.51 0.604,0.208 10 false 5 5.688,0.5 6.146,0.698 0.458,0.198 10 false STP 5.677,1.292 6.135,1.49 0.458,0.198 10 false ST1- 5.438,0.51 6.229,0.74 0.792,0.229 10 false 21 5.438,1.302 6.313,1.531 0.875,0.229 10 false 22 6.052,2.146 6.51,2.344 0.458,0.198 10 false ECM 5.729,2.146 6.646,2.365 0.917,0.219 10 false A24 2.135,3.229 4.948,3.438 2.813,0.208 10 false Skid Control ECU (Brake Actuator Assembly) 2.156,3.042 4.146,3.24 1.99,0.198 10 false A34 3.948,2.865 4.406,3.063 0.458,0.198 10 false STP 4.354,2.75 4.719,3.156 0.365,0.406 10 false 42 5.5,2.75 5.708,2.958 0.208,0.208 10 false 25 5.313,3.25 6.833,3.635 1.521,0.385 10 false Certification ECU (Smart Key ECU Assembly) 5.75,2.865 6.292,3.052 0.542,0.188 10 false STP1 5.042,3.25 5.25,3.458 0.208,0.208 10 false R8 3.073,4.271 4.854,4.625 1.781,0.354 10 false Shift Lock Control ECU (Shift Lock Control Unit Assembly) 3.073,4.063 5.063,4.26 1.99,0.198 10 false K27 4.354,3.781 4.896,3.969 0.542,0.188 10 false 4 3.979,3.906 4.438,4.104 0.458,0.198 10 false STP 5.76,3.906 6.219,4.104 0.458,0.198 10 false STP 5.5,3.802 5.865,4.208 0.365,0.406 10 false 43 5.531,4.313 5.927,4.552 0.396,0.24 10 false C111 5.948,4.313 6.344,4.552 0.396,0.24 10 false TCM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
E462804C03
1.479,0.083 1.885,0.323 0.406,0.24 1.302,1.333 1.135,1.885 true 2.292,1.333 2.781,1.594 true 2.063,1.365 2.083,1.875 true 0.115,0.104 0.344,0.271 0.229,0.167 10 false *a 1.563,0.115 1.99,0.333 0.427,0.219 10 false A85 2.844,1.542 3.01,1.708 0.167,0.167 10 false B 0.958,1.917 1.375,2.104 0.417,0.188 10 false GND 2.042,1.906 2.208,2.073 0.167,0.167 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A85 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-7 (B) - Body ground Always 11 to 14 V
A85-6 (B) - Body ground Ignition switch ON 11 to 14 V
A85-6 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

for A25A-FKS:

i.

Disconnect the A24 ECM connector.


ii.

Disconnect the A85 stop light switch assembly connector.


iii.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


iv.

Disconnect the R8 certification ECU (smart key ECU assembly) connector (w/ Smart Entry and Start System).


v.

Disconnect the K28 shift lock control ECU (shift lock control unit assembly) connector (w/o Smart Entry and Start System).


vi.

Disconnect the K27 shift lock control ECU (shift lock control unit assembly) connector (w/ Smart Entry and Start System).


vii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-22 (ST1-) - A85-5 (L) Always Below 1 Ω
A24-21 (STP) - A85-3 (L) Always Below 1 Ω
A24-22 (ST1-) or A85-5 (L) - Body ground Always 10 kΩ or higher
A24-21 (STP) or A85-3 (L) - Body ground Always 10 kΩ or higher




b.

for 2GR-FKS:

i.

Disconnect the A23 ECM connector.


ii.

Disconnect the A85 stop light switch assembly connector.


iii.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


iv.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


v.

Disconnect the K27 shift lock control ECU (shift lock control unit assembly) connector.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-42 (ST1-) - A85-5 (L) Always Below 1 Ω
A23-27 (STP) - A85-3 (L) Always Below 1 Ω
A23-42 (ST1-) or A85-5 (L) - Body ground Always 10 kΩ or higher
A23-27 (STP) or A85-3 (L) - Body ground Always 10 kΩ or higher




c.

for M20A-FKS:

i.

Disconnect the A24 ECM connector.


ii.

Disconnect the A85 stop light switch assembly connector.


iii.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


iv.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


v.

Disconnect the K27 shift lock control ECU (shift lock control unit assembly) connector.


vi.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-22 (ST1-) - A85-5 (L) Always Below 1 Ω
A24-21 (STP) - A85-3 (L) Always Below 1 Ω
A24-22 (ST1-) or A85-5 (L) - Body ground Always 10 kΩ or higher
A24-21 (STP) or A85-3 (L) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR