Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0463554 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK ECM (for A25A-FKS)


C370678N22
5.5,0.427 5.917,0.677 0.417,0.25 3.865,0.427 4.281,0.677 0.417,0.25 1.75,0.427 2.167,0.677 0.417,0.25 5.583,0.469 6.042,0.667 0.458,0.198 10 false A24 3.948,0.458 4.406,0.656 0.458,0.198 10 false C59 1.833,0.469 2.292,0.667 0.458,0.198 10 false C57

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A24-21 (STP) - A24-10 (E1) SB - W-B Stop light switch assembly signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
A24-22 (ST1-) - A24-10 (E1) LG - W-B Stop light switch assembly signal Ignition switch ON, brake pedal depressed Below 1 V
Ignition switch ON, brake pedal released 11 to 14 V
A24-27 (CCS) - A24-28 (ECCS) R - BE Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
CANCEL switch pushed 235 to 245 Ω
+RES switch pushed 617 to 643 Ω
-SET switch pushed 1509 to 1571 Ω


CHECK ECM (for 2GR-FKS)


A424791N05
2.458,0.354 2.854,0.594 0.396,0.24 5.906,0.354 6.302,0.594 0.396,0.24 2.542,0.396 2.948,0.625 0.406,0.229 10 false C96 5.979,0.396 6.385,0.656 0.406,0.26 10 false A23

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A23-27 (STP) - C96-53 (E1) SB - W-B Stop light switch assembly signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
A23-41 (CCS) - C96-53 (E1) R - W-B Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
CANCEL switch pushed 235 to 245 Ω
+RES switch pushed 617 to 643 Ω
-SET switch pushed 1509 to 1571 Ω
A23-42 (ST1-) - C96-53 (E1) LG - W-B Stop light switch assembly signal Ignition switch ON, brake pedal depressed Below 1 V
Ignition switch ON, brake pedal released 11 to 14 V


CHECK ECM (for M20A-FKS)


A425145N20
1.833,0.792 2.281,1.042 0.448,0.25 5.448,0.813 5.896,1.063 0.448,0.25 1.938,0.833 2.396,1.031 0.458,0.198 10 false C57 5.542,0.865 6,1.063 0.458,0.198 10 false A24

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A24-21 (STP) - A24-10 (E1) SB - W-B Stop light switch assembly signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
A24-22 (ST1-) - A24-10 (E1) LG - W-B Stop light switch assembly signal Ignition switch ON, brake pedal depressed Below 1 V
Ignition switch ON, brake pedal released 11 to 14 V
A24-27 (CCS) - A24-10 (E1) R - W-B Steering pad switch circuit Cruise control switch not pushed 1 MΩ or higher
Cruise control main switch pushed Below 2.5 Ω
CANCEL switch pushed 235 to 245 Ω
+RES switch pushed 617 to 643 Ω
-SET switch pushed 1509 to 1571 Ω


CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the GTS once the inspection has been completed.

·

Do not apply excessive force to the forward recognition camera connector.



B472992C11
1.76,1.01 2.146,1.219 0.385,0.208 1.76,0.594 2.146,0.802 0.385,0.208 1.844,1.042 2.156,1.24 0.313,0.198 10 false V25 1.885,0.615 2.198,0.813 0.313,0.198 10 false V6 2.229,0.625 2.542,0.823 0.313,0.198 10 false *A 2.229,1.042 2.542,1.24 0.313,0.198 10 false *B
*A Before Jan. 2022 Production *B From Jan. 2022 Production


a.

Measure the voltage and resistance according to the value(s) in the table below.

Before Jan. 2022 Production
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-3 (LKSW) - V6-10 (GND) V - W-B*1
V - LA*2
Steering pad switch assembly signal (distance control signal) Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) off 4.75 to 5.25 V
Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) on Below 1 V
V6-7 (IGB) - V6-10 (GND) LA-P - W-B*1
LA-P - LA*2
Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
V6-10 (GND) - Body ground W-B - Body ground*1
LA - Body ground*2
Ground Always Below 1 Ω

*1: for RHD without Headup Display

*2: excpt RHD without Headup Display


From Jan. 2022 Production
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V25-3 (LKSW) - V25-10 (GND) V - W-B*1
V - LA*2
Steering pad switch assembly signal (distance control signal) Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) off 4.75 to 5.25 V
Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) on Below 1 V
V25-7 (IGB) - V25-10 (GND) LA-P - W-B*1
LA-P - LA*2
Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
V25-10 (GND) - Body ground W-B - Body ground*1
LA - Body ground*2
Ground Always Below 1 Ω

*1: for RHD without Headup Display

*2: excpt RHD without Headup Display