Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0463554 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM. The ECM uses this signal to control cancellation of vehicle speed by the dynamic radar cruise control. When the ECM determines that terminals STP and ST1- of the stop light switch assembly are both less than 1 V, DTC P057162 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P057162 Brake Switch "A" Signal Compare Failure When the ignition switch is ON and the dynamic radar cruise control system is operating, the ECM detects that the voltage at terminal STP and ST1- are both less than 1 V for approximately 0.5 seconds or more.
·

Harness or connector

·

Stop light switch assembly

·

ECM


Cruise Control

WIRING DIAGRAM

for A25A-FKS


E456956E11
6.094,2.302 6.542,2.604 0.448,0.302 10 false ECM 3.125,2.479 5.417,2.677 2.292,0.198 10 false Stop Light Switch Assembly 3.583,1.417 3.74,1.615 0.156,0.198 10 false B 3.573,0.917 3.729,1.115 0.156,0.198 10 false B 4.177,0.792 4.333,0.99 0.156,0.198 10 false L 4.177,1.594 4.333,1.792 0.156,0.198 10 false L 3.563,1.927 3.99,2.125 0.427,0.198 10 false GND 2.115,1.563 3.115,1.833 1,0.271 10 false ECU-IG2 NO. 3 2.396,1.073 3.396,1.344 1,0.271 10 false STOP 0.615,0.885 2.302,1.083 1.688,0.198 10 false from Battery 0.083,1.417 1.51,1.792 1.427,0.375 10 false from IG2-NO. 2 Relay 3.385,0.813 3.542,1.01 0.156,0.198 10 false 7 4.333,1.458 4.49,1.656 0.156,0.198 10 false 5 3.385,1.813 3.542,2.01 0.156,0.198 10 false 2 3.375,1.292 3.531,1.49 0.156,0.198 10 false 6 4.333,0.688 4.49,0.885 0.156,0.198 10 false 3 3.135,2.313 3.594,2.531 0.458,0.219 10 false A85 5.427,0.656 5.646,0.875 0.219,0.219 10 false 21 5.438,1.427 5.771,1.646 0.333,0.219 10 false 22 5.667,0.688 6.125,0.885 0.458,0.198 10 false STP 5.677,1.469 6.135,1.667 0.458,0.198 10 false ST1- 2.563,2.979 3.531,3.177 0.969,0.198 10 false to Each ECU 5.792,2.302 6.125,2.521 0.333,0.219 10 false A24


for 2GR-FKS


E456956E12
6.094,2.302 6.542,2.604 0.448,0.302 10 false ECM 3.125,2.479 5.417,2.677 2.292,0.198 10 false Stop Light Switch Assembly 3.583,1.417 3.74,1.615 0.156,0.198 10 false B 3.573,0.917 3.729,1.115 0.156,0.198 10 false B 4.177,0.792 4.333,0.99 0.156,0.198 10 false L 4.177,1.594 4.333,1.792 0.156,0.198 10 false L 3.563,1.927 3.99,2.125 0.427,0.198 10 false GND 2.115,1.563 3.115,1.833 1,0.271 10 false ECU-IG2 NO. 3 2.396,1.073 3.396,1.344 1,0.271 10 false STOP 0.615,0.885 2.302,1.083 1.688,0.198 10 false from Battery 0.083,1.417 1.51,1.792 1.427,0.375 10 false from IG2-NO. 2 Relay 3.385,0.813 3.542,1.01 0.156,0.198 10 false 7 4.333,1.458 4.49,1.656 0.156,0.198 10 false 5 3.385,1.813 3.542,2.01 0.156,0.198 10 false 2 3.375,1.292 3.531,1.49 0.156,0.198 10 false 6 4.333,0.688 4.49,0.885 0.156,0.198 10 false 3 3.135,2.313 3.594,2.531 0.458,0.219 10 false A85 5.427,0.656 5.646,0.875 0.219,0.219 10 false 27 5.438,1.427 5.771,1.646 0.333,0.219 10 false 42 5.667,0.688 6.125,0.885 0.458,0.198 10 false STP 5.677,1.469 6.135,1.667 0.458,0.198 10 false ST1- 2.563,2.979 3.531,3.177 0.969,0.198 10 false to Each ECU 5.792,2.302 6.125,2.521 0.333,0.219 10 false A23


for M20A-FKS


E456956E13
6.094,2.302 6.542,2.604 0.448,0.302 10 false ECM 3.125,2.479 5.417,2.677 2.292,0.198 10 false Stop Light Switch Assembly 3.583,1.417 3.74,1.615 0.156,0.198 10 false B 3.573,0.917 3.729,1.115 0.156,0.198 10 false B 4.177,0.792 4.333,0.99 0.156,0.198 10 false L 4.177,1.594 4.333,1.792 0.156,0.198 10 false L 3.563,1.927 3.99,2.125 0.427,0.198 10 false GND 2.115,1.563 3.115,1.833 1,0.271 10 false ECU-IG2 NO. 3 2.396,1.073 3.396,1.344 1,0.271 10 false STOP 0.615,0.885 2.302,1.083 1.688,0.198 10 false from Battery 0.083,1.417 1.51,1.792 1.427,0.375 10 false from IG2-NO. 2 Relay 3.385,0.813 3.542,1.01 0.156,0.198 10 false 7 4.333,1.458 4.49,1.656 0.156,0.198 10 false 5 3.385,1.813 3.542,2.01 0.156,0.198 10 false 2 3.375,1.292 3.531,1.49 0.156,0.198 10 false 6 4.333,0.688 4.49,0.885 0.156,0.198 10 false 3 3.135,2.313 3.594,2.531 0.458,0.219 10 false A85 5.427,0.656 5.646,0.875 0.219,0.219 10 false 21 5.438,1.427 5.771,1.646 0.333,0.219 10 false 22 5.667,0.688 6.125,0.885 0.458,0.198 10 false STP 5.677,1.469 6.135,1.667 0.458,0.198 10 false ST1- 2.563,2.979 3.531,3.177 0.969,0.198 10 false to Each ECU 5.792,2.302 6.125,2.521 0.333,0.219 10 false A24


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
E462804C04
1.479,0.083 1.885,0.323 0.406,0.24 1.302,1.333 1.135,1.885 true 2.292,1.333 2.781,1.594 true 2.063,1.365 2.083,1.875 true 0.115,0.104 0.344,0.271 0.229,0.167 10 false *a 1.563,0.115 1.99,0.333 0.427,0.219 10 false A85 2.844,1.542 3.01,1.708 0.167,0.167 10 false B 0.958,1.917 1.375,2.104 0.417,0.188 10 false GND 2.042,1.906 2.208,2.073 0.167,0.167 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A85-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A85-7 (B) - Body ground Always 11 to 14 V
A85-6 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the A85 stop light switch assembly connector.


b.

Disconnect the A24*1, A23*2 or A24*3 ECM connector.

*1: for A25A-FKS

*2: for 2GR-FKS

*3: for M20A-FKS



c.

Disconnect each ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for A25A-FKS:
Tester Connection Condition Specified Condition
A85-3 (L) - A24-21 (STP) Always Below 1 Ω
A85-5 (L) - A24-22 (ST1-) Always Below 1 Ω
A85-3 (L) or A24-21 (STP) - Body ground Always 10 kΩ or higher
A85-5 (L) or A24-22 (ST1-) - Body ground Always 10 kΩ or higher

for 2GR-FKS:
Tester Connection Condition Specified Condition
A85-3 (L) - A23-27 (STP) Always Below 1 Ω
A85-5 (L) - A23-42 (ST1-) Always Below 1 Ω
A85-3 (L) or A23-27 (STP) - Body ground Always 10 kΩ or higher
A85-5 (L) or A23-42 (ST1-) - Body ground Always 10 kΩ or higher

for M20A-FKS:
Tester Connection Condition Specified Condition
A85-3 (L) - A24-21 (STP) Always Below 1 Ω
A85-5 (L) - A24-22 (ST1-) Always Below 1 Ω
A85-3 (L) or A24-21 (STP) - Body ground Always 10 kΩ or higher
A85-5 (L) or A24-22 (ST1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR