The steering pad switch assembly outputs the on/off signal and various control signals to the ECM.
The ECM performs cruise control according to the signals received from the steering pad switch assembly.
for A25A-FKS
for 2GR-FKS
for M20A-FKS
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Before replacing the ECM, refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Cancel Switch | CANCEL switch status | ON or OFF | ON: CANCEL switch on
OFF: CANCEL switch off |
- |
| -SET Switch | -SET switch status | ON or OFF | ON: -SET switch on
OFF: -SET switch off |
- |
| +RES Switch | +RES switch status | ON or OFF | ON: +RES switch on
OFF: +RES switch off |
- |
| Cruise Main Switch Operation Condition | Cruise control main switch status | ON or OFF | ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed |
- |
| Tester Display |
|---|
| Cancel Switch |
| -SET Switch |
| +RES Switch |
| Cruise Main Switch Operation Condition |
The value of each Data List item changes according to the operation of the steering pad switch assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
NG
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A24*1, A23*2 or A24*3 connector.
*1: for A25A-FKS
*2: for 2GR-FKS
*3: for M20A-FKS
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-13 (CCS) - A24-27 (CCS) | Always | Below 1 Ω |
| K22-2 (ECC) - A24-28 (ECCS) | Always | Below 1 Ω |
| K22-13 (CCS) or A24-27 (CCS) - Body ground | Always | 10 kΩ or higher |
| K22-2 (ECC) or A24-28 (ECCS) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-41 (CCS) - K22-13 (CCS) | Always | Below 1 Ω |
| K22-2 (ECC) - Body ground | Always | Below 1 Ω |
| A23-41 (CCS) or K22-13 (CCS) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-13 (CCS) - A24-27 (CCS) | Always | Below 1 Ω |
| K22-2 (ECC) - A24-28 (ECCS) | Always | Below 1 Ω |
| K22-13 (CCS) or A24-27 (CCS) - Body ground | Always | 10 kΩ or higher |
| K22-2 (ECC) or A24-28 (ECCS) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for A25A-FKS, M20A-FKS) | A |
| OK (for 2GR-FKS) | B |
| NG | C |
A
B
C
Disconnect the A24*1 or A24*2 ECM connector.
*1: for A25A-FKS
*2: for M20A-FKS
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-10 (E1) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-10 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for M20A-FKS: Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>ECM>REMOVAL
NG