The vehicle-to-vehicle distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The vehicle-to-vehicle distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the vehicle-to-vehicle distance control switch while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.
for A25A-FKS
for 2GR-FKS
for M20A-FKS
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
When replacing the forward recognition camera, replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT
Before replacing the ECM, refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle-to-vehicle Distance Control Switch | Vehicle-to-vehicle distance control switch signal | ON or OFF | ON: Vehicle-to-vehicle distance control switch pushed
OFF: Vehicle-to-vehicle distance control switch not pushed |
- |
| Tester Display |
|---|
| Vehicle-to-vehicle Distance Control Switch |
The value of the Data List item changes according to the operation of the vehicle-to-vehicle distance control switch.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
NG
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the V6*1, V25*2 forward recognition camera connector.
*1: Before Jan. 2022 Production
*2: From Jan. 2022 Production
Disconnect the A24 ECM connector (for A25A-FKS).
Disconnect the A24 ECM connector (for M20A-FKS).
Before Jan. 2022 Production:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-6 (DIST) - V6-3 (LKSW) | Always | Below 1 Ω |
| K22-2 (ECC) - A24-28 (ECCS) | Always | Below 1 Ω |
| K22-6 (DIST) or V6-3 (LKSW) - Body ground | Always | 10 kΩ or higher |
| K22-2 (ECC) or A24-28 (ECCS) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-6 (DIST) - V6-3 (LKSW) | Always | Below 1 Ω |
| K22-2 (ECC) - Body ground | Always | Below 1 Ω |
| K22-6 (DIST) or V6-3 (LKSW) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-6 (DIST) - V6-3 (LKSW) | Always | Below 1 Ω |
| K22-2 (ECC) - A24-28 (ECCS) | Always | Below 1 Ω |
| K22-6 (DIST) or V6-3 (LKSW) - Body ground | Always | 10 kΩ or higher |
| K22-2 (ECC) or A24-28 (ECCS) - Body ground | Always | 10 kΩ or higher |
From Jan. 2022 Production:
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-6 (DIST) - V25-3 (LKSW) | Always | Below 1 Ω |
| K22-2 (ECC) - A24-28 (ECCS) | Always | Below 1 Ω |
| K22-6 (DIST) or V25-3 (LKSW) - Body ground | Always | 10 kΩ or higher |
| K22-2 (ECC) or A24-28 (ECCS) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-6 (DIST) - V25-3 (LKSW) | Always | Below 1 Ω |
| K22-2 (ECC) - Body ground | Always | Below 1 Ω |
| K22-6 (DIST) or V25-3 (LKSW) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-6 (DIST) - V25-3 (LKSW) | Always | Below 1 Ω |
| K22-2 (ECC) - A24-28 (ECCS) | Always | Below 1 Ω |
| K22-6 (DIST) or V25-3 (LKSW) - Body ground | Always | 10 kΩ or higher |
| K22-2 (ECC) or A24-28 (ECCS) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for A25A-FKS) | A |
| OK (for M20A-FKS) | B |
| OK (for 2GR-FKS) | C |
| NG | D |
A
B
C
D
| *a | Component without harness connected
(ECM) |
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-28 (ECCS) - A24-10 (E1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(ECM) |
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-28 (ECCS) - A24-10 (E1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG