The forward recognition camera receives LTA switch signals from the steering pad switch assembly.
for A25A-FKS
for 2GR-FKS
for M20A-FKS
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| LDA Control | Whether lane tracing assist system control is permitted or not | Prohibit or Permit | Prohibit: Lane tracing assist system control not possible
Permit: Lane tracing assist system control possible |
- |
| Tester Display |
|---|
| LDA Control |
| Result | Proceed to |
|---|---|
| The value of the Data List item changes in accordance with the operation of the LTA switch | A |
| The value of the Data List item does not change in accordance with the operation of the LTA switch | B |
A
B
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the V6*1, V25*2 forward recognition camera connector.
*1: Before Jan. 2022 Production
*2: From Jan. 2022 Production
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-6 (DIST) - V6-3 (LKSW) | Always | Below 1 Ω |
| K22-6 (DIST) or V6-3 (LKSW) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-6 (DIST) - V25-3 (LKSW) | Always | Below 1 Ω |
| K22-6 (DIST) or V25-3 (LKSW) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for A25A-FKS, M20A-FKS) | A |
| OK (for 2GR-FKS) | B |
| NG | C |
A
B
C
Disconnect the A24 ECM connector. (for A25A-FKS)
Disconnect the A24 ECM connector. (for M20A-FKS)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-2 (ECC) - A24-28 (ECCS) | Always | Below 1 Ω |
| K22-2 (ECC) or A24-28 (ECCS) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-2 (ECC) - A24-28 (ECCS) | Always | Below 1 Ω |
| K22-2 (ECC) or A24-28 (ECCS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-2 (ECC) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG