The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Microphone signal is lost | ·
Roof console box sub-assembly ·
Telephone microphone assembly ·
Radio and display receiver assembly ·
Telematics transceiver* ·
Harness or connector |
*: w/ Telematics Transceiver
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (w/ Sliding Roof) | A |
| OK (w/o Sliding Roof and w/o Telematics Transceiver) | B |
| OK (w/o Sliding Roof and w/ Telematics Transceiver) | C |
| NG | D |
A
B
C
D
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the V14 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-25 (SNS2) - V14-6 (SNS2) | Always | Below 1 Ω |
| K2-22 (MIN-) - V14-7 (MCO-) | Always | Below 1 Ω |
| K2-25 (SNS2) or V14-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| K2-22 (MIN-) or V14-7 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 (SNS2) - 7 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - V14-6 (SNS2) | Always | Below 1 Ω |
| B-2 - V14-7 (MCO-) | Always | Below 1 Ω |
| B-1 or V14-6 (SNS2) - V14-15 (GND) | Always | 10 kΩ or higher |
| B-2 or V14-7 (MCO-) - V14-15 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the V13 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-25 (SNS2) - V13-12 (SNS2) | Always | Below 1 Ω |
| K2-22 (MIN-) - V13-11 (MCO-) | Always | Below 1 Ω |
| K2-25 (SNS2) or V13-12 (SNS2) - Body ground | Always | 10 kΩ or higher |
| K2-22 (MIN-) or V13-11 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 12 (SNS2) - 11 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - V13-12 (SNS2) | Always | Below 1 Ω |
| B-2 - V13-11 (MCO-) | Always | Below 1 Ω |
| B-1 or V13-12 (SNS2) - V13-4 (GND) | Always | 10 kΩ or higher |
| B-2 or V13-11 (MCO-) - V13-4 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K156 telematics transceiver connector.
Disconnect the V20 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K156-7 (MCI-) - V20-4 (MCO-) | Always | Below 1 Ω |
| K156-7 (MCI-) or V20-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the K156 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-22 (MIN-) - K156-32 (MCO-) | Always | Below 1 Ω |
| K2-22 (MIN-) or K156-32 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K2 radio and display receiver assembly connector.
Disconnect the V20 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K2-25 (SNS2) - V20-3 (SNS2) | Always | Below 1 Ω |
| K2-25 (SNS2) or V20-3 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the K156 telematics transceiver connector.
Connect the K2 radio and display receiver assembly connector.
| *a | Component with harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K156-7 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SNS2) - 4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the B telephone microphone assembly connector.
| *a | Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 - V20-3 (SNS2) | Always | Below 1 Ω |
| B-2 - V20-4 (MCO-) | Always | Below 1 Ω |
| B-1 or V20-3 (SNS2) - V20-11 (GND) | Always | 10 kΩ or higher |
| B-2 or V20-4 (MCO-) - V20-11 (GND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG