Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  CHECK FOR INTERMITTENT PROBLEMS  


CHECK FOR INTERMITTENT PROBLEMS


HINT:

A momentary interruption (open circuit) in the connectors and/or wire harness between the sensors and ECUs can be detected using the Data List function of the GTS.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Brake/EPB / Data List.


f.

Check the data related to power supply fluctuations.

HINT:

A momentary interruption (open circuit) cannot be detected for 3 seconds after the ignition switch is turned to ON (initial check).


Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EFI Communication Open EFI communication open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
Related DTC: U010087
Yaw Rate Open Yaw rate sensor (airbag sensor assembly) open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
Related DTC: U012587
Deceleration Open Acceleration sensor (airbag sensor assembly) open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
Related DTC: U012587
Steering Open Steering angle sensor open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
Related DTC: U012687

g.

Push the line graph button to display the line graph.


h.

Check for intermittent shorts, etc.

OK:

Normal is displayed.


HINT:

If "Under intermittent" remains displayed on the GTS, measure the resistance between the skid control ECU (brake actuator assembly) and the each sensor or ECM.



i.

While observing the screen, gently jiggle the connector or wire harness between the ECU and each sensors, or between ECUs.

OK:

Normal is displayed.


HINT:
·

If a momentary interruption occurs and Under intermittent is displayed on the GTS, Under intermittent will remain displayed on the GTS for 1 second after the circuit returns to normal.

C399553E26
0.073,0.073 5.26,0.531 5.188,0.458 10 false Reference: GTS display at momentary interruption 0.208,0.875 1.823,1.292 1.615,0.417 10 false Wire Harness condition 0.948,1.927 1.792,2.26 0.844,0.333 10 false Line Graph 2.615,1.406 3.406,1.604 0.792,0.198 10 false 1 second 4.24,1.417 5.177,1.635 0.938,0.219 10 false 2 seconds 4.083,0.375 5.385,0.688 1.302,0.313 10 false 1.5 seconds 2.427,0.354 3.458,0.552 1.031,0.198 10 false 0.5 seconds 5.656,1.76 6.927,2.073 1.271,0.313 10 false Under intermittent 5.667,2.135 6.417,2.469 0.75,0.333 10 false Normal 5.625,0.708 7.104,1 1.479,0.292 10 false Momentary interruption 5.635,1.073 6.385,1.396 0.75,0.323 10 false Normal

·

If the display changes, this indicates that there has been a momentary interruption (open circuit) in the connector and/or wire harness. In this case, repair or replace the connectors and/or wire harnesses as one of them is faulty.