Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C360725C12
0.125,0.146 0.427,0.354 0.302,0.208 10 false *a
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -


HINT:
·

As a waterproof connector is used for the brake actuator assembly, voltage and waveform inspections cannot be performed with the connector connected.


·

Use the GTS to read data and perform Active Tests when inspecting the operation and communication status of the brake actuator assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST



Terminal No. (Symbol) Terminal Description
1 (+BM) ABS motor relay power supply
2 -
3 -
4 -
5 (CANH) CAN communication line H
6 (CSW) VSC OFF switch input
7 (FL-) Front wheel speed LH (-) signal input
8 -
9 -
10 (STPO) Stop light control relay (stop light switch assembly) output
11 -
12 -
13 -
14 (GND2) Pump motor ground
15 -
16 -
17 -
18 -
19 (CANL) CAN communication line L
20 -
21 (FR+) Front wheel speed RH (+) power supply output
22 (RR+) Rear wheel speed RH (+) power supply output
23 (RL-) Rear wheel speed LH (-) signal input
24 (FL+) Front wheel speed LH (+) power supply output
25 -
26 (FR-) Front wheel speed RH (-) signal input
27 -
28 -
29 -
30 (+BS) ABS solenoid relay power supply
31 -
32 -
33 -
34 (SP1) Speed signal output
35 -
36 (IG1) IG1 power source input
37 (RR-) Rear wheel speed RH (-) signal input
38 -
39 (RL+) Rear wheel speed LH (+) power supply output
40 -
41 -
42 (STP) Stop light switch assembly signal input
43 (HZRI) Brake hold switch (electric parking brake switch assembly) input
44 (STP2) Stop light signal input
45 -
46 (GND1) Skid control ECU (brake actuator assembly) ground


TERMINAL INSPECTION


a.

Disconnect the A34 skid control ECU (brake actuator assembly) connector and measure the voltage and resistance on the wire harness side.

C380240C40
1.448,0.698 1.885,0.948 0.438,0.25 0.146,0.094 0.458,0.25 0.313,0.156 10 false *a 1.521,0.74 1.979,0.938 0.458,0.198 10 false A34
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
- -



b.

Measure the voltage or resistance according to the value(s) in the table below.

Standard
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A34-1 (+BM) - Body ground B - Body ground ABS motor relay power supply Always 11 to 14 V
A34-6 (CSW) - Body ground P - Body ground VSC OFF switch input VSC OFF switch on → off (Pressed → not pressed) Below 1 Ω → 10 kΩ or higher
A34-10 (STPO) - Body ground L - Body ground Stop light control relay (stop light switch assembly) output Always 11 to 14 V
A34-14 (GND2) - Body ground W-B - Body ground Pump motor ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω
A34-30 (+BS) - Body ground G - Body ground ABS solenoid relay power supply Always 11 to 14 V
A34-36 (IG1) - Body ground B - Body ground IG1 power source input Ignition switch ON 11 to 14 V
A34-42 (STP) - Body ground GR - Body ground Stop light switch assembly signal input Stop light switch assembly on → off (Brake pedal depressed → released) 11 to 14 V → 1.5 V or less
A34-43 (HZRI) - Body ground LG - Body ground Brake hold switch (electric parking brake switch assembly) input Brake hold switch (electric parking brake switch assembly) on → off (Pressed → not pressed) Below 1 Ω → 10 kΩ or higher
A34-44 (STP2) - Body ground R - Body ground Stop light signal input Stop light switch assembly on → off (Brake pedal depressed → released) 11 to 14 V → 1.5 V or less
A34-46 (GND1) - Body ground W-B - Body ground Skid control ECU (brake actuator assembly) ground 1 minute or more after disconnecting the cable from the negative (-) battery terminal Below 1 Ω