When the position control ECU assembly (driver seat) does not receive a reclining motor position sensor signal despite the seat having been moved forward or rearward by power seat motor operation, this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2651 | Reclining Sensor Malfunction | Reclining motor position sensor signal not received when power seat moved forward or rearward | ·
Position control ECU assembly (driver seat) ·
Reclining motor (Front seatback frame sub-assembly (driver seat)) ·
Wire harness or connector |
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B2651 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Driver Seat / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Reclining | Seat reclining operation | OFF/Rear/Front | - |
| Tester Display |
|---|
| Seat Reclining |
Reclining motor operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the c1 reclining motor (front seatback frame sub-assembly (driver seat)) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| c1-2 - c1-3 | Reclining switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Reclining Motor (Front Seatback Frame Sub-assembly (Driver Seat))) |
Reconnect the c1 reclining motor (front seatback frame sub-assembly (driver seat)) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| c1-2 - Body ground | Reclining motor operating | 4.5 to 4.8 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b25 position control ECU assembly (driver seat) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b25-11 (SSRR) - c1-2 | Always | Below 1 Ω |
| b25-11 (SSRR) or c1-2 - Body ground | Always | 10 kΩ or higher |
| b25-12 (SENG) - c1-3 | Always | Below 1 Ω |
| b25-12 (SENG) or c1-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the reclining motor (front seatback frame sub-assembly (driver seat)).
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
Inspect the reclining motor (front seatback frame sub-assembly (driver seat)).
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the b23 and b24 position control ECU assembly (driver seat) connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b23-10 (RCL+) - c1-1 | Always | Below 1 Ω |
| b23-10 (RCL+) or c1-1 - Body ground | Always | 10 kΩ or higher |
| b24-6 (RCL-) - c1-4 | Always | Below 1 Ω |
| b24-6 (RCL-) or c1-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG