Refer to DTC P107A11.
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>P107A11
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P107A2A | Fuel Rail Pressure Sensor (Low) Signal Stuck in Range | When the target fuel pressure for the low pressure side changes, the change in the fuel pressure sensor (for low pressure side) value is abnormal (2 trip detection logic). | ·
Leak of fuel ·
Fuel pump control ECU ·
Fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) ·
Fuel pump (for low pressure side) ·
Fuel main valve assembly (for high pressure) ·
ECM |
Comes on | DTC stored | SAE Code: P107B |
| P107A64 | Fuel Rail Pressure Sensor (Low) Signal Plausibility Failure | When the fuel pump on the low pressure side is operated at the maximum during a fuel cut, the low pressure side fuel pressure is higher or lower than threshold (2 trip detection logic). | ·
Leak of fuel ·
Fuel pump control ECU ·
Fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) ·
Fuel pump (for low pressure side) ·
Fuel main valve assembly (for high pressure) ·
ECM |
Comes on | DTC stored | SAE Code: P107B |
If the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) value does not follow the change in the target low pressure side fuel pressure, it is judged as a malfunction. If this malfunction is detected in 2 consecutive driving cycles, the ECM will illuminate the MIL and store DTC P107A2A.
If the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) value is less than or higher than the threshold value when the fuel pump on the low pressure side is operated at the maximum during a fuel cut, it is judged as a malfunction has occurred. If this malfunction is detected for 2 consecutive driving cycles, the ECM will illuminate the MIL and store DTC P107A64.
| Required Sensors/Components (Main) | Fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) |
| Required Sensors/Components (Related) | ECM (atmospheric pressure sensor) |
| Frequency of Operation | Continuous: Stuck monitor
Once per driving cycle: Correlation monitor |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) [A].
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
Drive the vehicle at 50 to 80 km/h (31 to 50 mph) for 15 minutes or more [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle while keeping the engine load as constant as possible.
With the shift lever in S [D], accelerate the vehicle to 64 km/h (40 mph) or more by depressing the accelerator pedal for at least 10 seconds [E].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Soon after performing step [E] above, release the accelerator pedal for 10 seconds or more without depressing the brake pedal in order to execute fuel-cut control [F].
Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).
Repeat steps [D] through [F] above at least 3 times in one driving cycle.
Enter the following menus: Powertrain / Engine / Trouble Codes [G].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P107A2A.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [C] through [G] again.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) [A].
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
Drive the vehicle at approximately 80 km/h (50 mph) for 10 seconds or more, and then decelerate the vehicle by releasing the accelerator pedal for 10 seconds or more to perform the fuel-cut [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P107A64.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [C] through [D] again.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs and record the Freeze Frame Data.
| Result | Proceed to |
|---|---|
| DTC P107A2A is output | A |
| DTC P107A64 is output | B |
| DTC P107A2A or P107A64 and P008A00 are output | C |
| DTC P107A2A or P107A64 and P008B00 are output | D |
| DTC P107A2A, P107A64, P008A00 and/or P008B00 and other DTCs are output | E |
If any DTCs other than P107A2A, P107A64, P008A00 and/or P008B00 are output, troubleshoot those DTCs first.
A
B
C
D
E
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Tester Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Start the engine.
Record the Fuel Pressure (Low) / Fuel Pressure 2 value.
Turn the engine switch off.
Discharge the fuel pressure.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
Remove the EFI-MAIN NO. 2 fuse from the engine room relay block and junction block assembly.
Start the engine.
After the engine has stopped on its own, turn the engine switch off.
If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine.
Crank the engine again and make sure that the engine does not start.
Install the EFI-MAIN NO. 2 fuse.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Tester Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Compare the Fuel Pressure (Low) / Fuel Pressure 2 value recorded with the engine running to the Fuel Pressure (Low) / Fuel Pressure 2 value currently shown on the GTS.
| Result | Proceed to |
|---|---|
| Fuel Pressure (Low) / Fuel Pressure 2 value drops | A |
| Fuel Pressure (Low) / Fuel Pressure 2 value does not fluctuate | B |
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P107A2A or P107A64.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P107A2A or P107A64 is output) |
B |
A
B
Install the fuel pressure gauge (for low pressure line of low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless) / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Active Test Display |
|---|
| Control the Fuel Pump Duty Ratio (Brushless) |
| Data List Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Compare the values in the Data List using the GTS and the fuel pressure gauge when the Active Test was performed.
| GTS Operation | Standard |
|---|---|
| Low | Data List value and fuel pressure gauge are within +/-50 kPa of each other |
| High |
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Read the Freeze Frame Data value from step 1.
| Tester Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
| Result | Proceed to |
|---|---|
| Fuel Pressure (Low) / Fuel Pressure 2 value is 770 kPag or higher | A |
| Fuel Pressure (Low) / Fuel Pressure 2 value is 540 kPag or less | B |
A
B
Check around and beneath the vehicle for fuel leaks, fumes, etc.
No fuel leaks present.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless).
| Tester Display |
|---|
| Control the Fuel Pump Duty Ratio (Brushless) |
Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.
| GTS Operation | Standard |
|---|---|
| High | Operating sounds can be heard from fuel pump (for low pressure side) |
Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Discharge the fuel pressure.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
Remove the EFI-MAIN NO. 2 fuse from the engine room relay block and junction block assembly.
Start the engine.
After the engine has stopped on its own, turn the engine switch off.
If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine.
Crank the engine again and make sure that the engine does not start.
Install the EFI-MAIN NO. 2 fuse.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless) / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Active Test Display |
|---|
| Control the Fuel Pump Duty Ratio (Brushless) |
| Data List Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Read the value displayed on the GTS when the Active Test was performed.
| GTS Operation | Standard |
|---|---|
| Low to High | When switching from Low to High, Fuel Pressure (Low) / Fuel Pressure 2 value changes |
Once the fuel pressure becomes high, the fuel pressure will not decrease, even when switched from High to Low. Therefore, make sure that the fuel pressure is low before checking that the fuel pressure changes when switching from Low to High.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Discharge the fuel pressure.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
Remove the EFI-MAIN NO. 2 fuse from the engine room relay block and junction block assembly.
Start the engine.
After the engine has stopped on its own, turn the engine switch off.
If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine.
Crank the engine again and make sure that the engine does not start.
Install the EFI-MAIN NO. 2 fuse.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless) / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Active Test Display |
|---|
| Control the Fuel Pump Duty Ratio (Brushless) |
| Data List Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Read the value displayed on the GTS when the Active Test was performed.
| GTS Operation | Fuel Pressure (Low) / Fuel Pressure 2 |
|---|---|
| Low | 50 kPag or higher |
| High | 420 kPag or higher |
Once the fuel pressure becomes high, the fuel pressure will not decrease, even when switched from High to Low. Therefore, make sure that the fuel pressure is low before checking that the fuel pressure changes when switching from Low to High.
Actual Low and High values are as shown above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the fuel pressure gauge (for low pressure line of low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless) / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Active Test Display |
|---|
| Control the Fuel Pump Duty Ratio (Brushless) |
| Data List Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Compare the values in the Data List using the GTS and the fuel pressure gauge when the Active Test was performed.
| GTS Operation | Standard |
|---|---|
| Low | Data List value and fuel pressure gauge are within +/-50 kPa of each other |
| High |
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P107A2A or P107A64.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P107A2A or P107A64 is output) |
B |
A
B
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Tester Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Record the Fuel Pressure (Low) / Fuel Pressure 2 value.
Turn the engine switch off.
Wait for 10 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Tester Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Compare the Fuel Pressure (Low) / Fuel Pressure 2 value recorded with the engine running to the Fuel Pressure (Low) / Fuel Pressure 2 value currently shown on the GTS.
| Result | Proceed to |
|---|---|
| Fuel Pressure (Low) / Fuel Pressure 2 value is maintained | A |
| Fuel Pressure (Low) / Fuel Pressure 2 value drops | B |
Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
A
B
Install the fuel pressure gauge (for low pressure line of low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless) / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Active Test Display |
|---|
| Control the Fuel Pump Duty Ratio (Brushless) |
| Data List Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Read the values in the Data List using the GTS and the fuel pressure gauge when the Active Test was performed.
| GTS Operation | Result | Proceed to |
|---|---|---|
| Low to High | Data List value does not change, but fuel pressure gauge changes | A |
| Data List value and fuel pressure gauge do not change | B |
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
A
B
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Tester Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Record the Fuel Pressure (Low) / Fuel Pressure 2 value.
Turn the engine switch off.
Discharge the fuel pressure.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
Remove the EFI-MAIN NO. 2 fuse from the engine room relay block and junction block assembly.
Start the engine.
After the engine has stopped on its own, turn the engine switch off.
If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine.
Crank the engine again and make sure that the engine does not start.
Install the EFI-MAIN NO. 2 fuse.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Tester Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Compare the Fuel Pressure (Low) / Fuel Pressure 2 value recorded with the engine running to the Fuel Pressure (Low) / Fuel Pressure 2 value currently shown on the GTS.
| Result | Proceed to |
|---|---|
| Fuel Pressure (Low) / Fuel Pressure 2 value drops | A |
| Fuel Pressure (Low) / Fuel Pressure 2 value is maintained | B |
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
A
B
Install the fuel pressure gauge (for low pressure line of low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio (Brushless) / Data List / Fuel Pressure (Low) / Fuel Pressure 2.
| Active Test Display |
|---|
| Control the Fuel Pump Duty Ratio (Brushless) |
| Data List Display |
|---|
| Fuel Pressure (Low) / Fuel Pressure 2 |
Compare the values in the Data List using the GTS and the fuel pressure gauge when the Active Test was performed.
| GTS Operation | Standard |
|---|---|
| Low | Data List value and fuel pressure gauge are within +/-50 kPa of each other |
| High |
Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/ Canister Pump Module)>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P107A2A or P107A64.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P107A2A or P107A64 is output) |
B |
A
B