Refer to DTC P001001.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>P001001
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P136001 | "A" Camshaft Position Actuator Bank 1 General Electrical Failure | While engine is running, malfunction in rotation signal (VTS) of cam timing control motor with EDU assembly is detected for 3 seconds (1 trip detection logic). | ·
Cam timing control motor with EDU assembly ·
Open or short in cam timing control motor with EDU assembly circuit ·
VVT relay ·
ECM |
Comes on | DTC stored | SAE Code: P1360 |
| Vehicle Condition | Fail-Safe |
|---|---|
·
Engine difficult to start ·
Lack of power |
The cam timing control motor with EDU assembly is operated to the most retarded position. |
This DTC is output when a rotation signal malfunction is detected in the cam timing control motor with EDU assembly. While the engine is running, if a rotation signal (VTS) malfunction is detected, a DTC is immediately output (1 trip detection logic).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Idle the engine for 30 seconds or more [A].
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes [B].
Read pending the DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P136001.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [A] through [B] again.
Inspect the fuses for circuits related to this system before performing the following procedure.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Cam Timing Control Motor with EDU Assembly) |
Disconnect the cam timing control motor with EDU assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C79-2 (VB1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cam timing control motor with EDU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C79-3 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check installation condition.
Check that the 3 installation bolts of the cam timing control motor with EDU assembly are tightened to the specified torque.
21 N*m (214 kgf*cm, 15 ft.*lbf)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cam timing control motor with EDU assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C79-6 (VTS) - C57-70 (EMR1) | Always | Below 1 Ω |
| C79-6 (VTS) or C57-70 (EMR1) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the cam timing control motor with EDU assembly.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>CAMSHAFT TIMING CONTROL MOTOR>REMOVAL
Perform "Inspection After Repair" after replacing the cam timing control motor with EDU assembly.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P136001 is output | B |
A
B
Inspect the VVT relay.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the VVT relay from engine room relay block and junction block assembly.
Disconnect the cam timing control motor with EDU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (VVT relay holder) - C79-2 (VB1) | Always | Below 1 Ω |
| 5 (VVT relay holder) or C79-2 (VB1) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | VVT Relay Holder |
Remove the VVT relay from engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (VVT relay holder) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | VVT Relay Holder |
Remove the VVT relay from engine room relay block and junction block assembly.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 (VVT relay holder) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG