Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for Toyota Connected Services) › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _072211 TELEMATICS _0466472 TELEMATICS SYSTEM(for Toyota Connected Services) Y

TELEMATICS  TELEMATICS SYSTEM(for Toyota Connected Services)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the telematics system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CHECK PROBLEM SYMPTOM
2.CHECK PROBLEM SYMPTOM
a.

The telematics system provides a variety of functions. Therefore, it is important to identify whether a malfunction is related to the communication system, including radio wave conditions, or any other systems. Carefully confirm the conditions that caused the malfunction in order to determine if a temporary problem with the radio wave signal conditions caused the malfunction.

Displayed Message and Problem Symptom Cause
A message is temporarily displayed indicating to try again after waiting for a while because the lines are busy. This is caused when there is a problem with the radio wave signal conditions or when the base station is busy. This is not a malfunction (inform the customer that this is not a malfunction and ask them to use the system as is).


Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY
3.INSPECT AUXILIARY BATTERY
a.

Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V (Ignition switch off)


HINT:

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

5.CHECK FOR DTC*

B

5.CHECK FOR DTC*
a.

Refer to DTC Check/Clear.

Body Electrical > Telematics > Trouble Codes
50001 459

Result:
Result Proceed to
DTCs are output. A
DTCs are not output. B



A

6.CLEAR DTC*

B

9.PROBLEM SYMPTOMS TABLE
6.CLEAR DTC*
a.

Refer to DTC Check/Clear.

Body Electrical > Telematics > Clear DTCs
50002 459
HINT:

The current DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.



Result:
Proceed to
NEXT



NEXT

7.RECHECK FOR DTC*
7.RECHECK FOR DTC*
a.

Refer to DTC Check/Clear.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B


HINT:
·

Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.

·

Check the DTCs and inspect the area that the code indicates.





A

8.CHECK VEHICLE CONTROL HISTORY*

B

11.CHECK CIRCUIT
8.CHECK VEHICLE CONTROL HISTORY*
a.

Check for vehicle control history and note any codes that are output.

Body Electrical > Telematics > Utility
Tester Display
Vehicle Control History (RoB)
50005 459 55

Result:
Result Proceed to
No vehicle control history is output A
Any vehicle control history is output B



A

9.PROBLEM SYMPTOMS TABLE

B

9.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptom does not recur and no DTCs are output, perform the simulation method.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING




A

10.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

B

11.CHECK CIRCUIT
10.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM

NEXT

11.CHECK CIRCUIT
11.CHECK CIRCUIT
a.

Adjust, repair or replace as necessary.

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION



Result:
Proceed to
NEXT



NEXT

12.RECHECK FOR DTC*
12.RECHECK FOR DTC*
HINT:

After clearing DTCs, recheck for DTCs.


Body Electrical > Telematics > Clear DTCs
50002 459
Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Proceed to
NEXT



NEXT

13.PERFORM CONFIRMATION TEST
13.PERFORM CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END