This DTC is stored when a microphone signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B157213 | Microphone Circuit Open | Current at terminal MCVD is lower than the malfunction threshold for 10 seconds or more while the ignition switch is ON | ·
Telematics transceiver ·
Roof console box sub-assembly ·
Telephone microphone assembly ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 10 seconds or more.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the K156 telematics transceiver connector.
Disconnect the V20 roof console box sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K156-5 (MCVD) - V20-6 (MACC) | Always | Below 1 Ω |
| K156-6 (MCI+) - V20-5 (MCO+) | Always | Below 1 Ω |
| K156-7 (MCI-) - V20-4 (MCO-) | Always | Below 1 Ω |
| K156-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| K156-5 (MCVD) or V20-6 (MACC) - Body ground | Always | 10 kΩ or higher |
| K156-6 (MCI+) or V20-5 (MCO+) - Body ground | Always | 10 kΩ or higher |
| K156-7 (MCI-) or V20-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Roof Console Box Sub-assembly) |
Remove the roof console box sub-assembly but do not disconnect the connectors.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| V20-6 (MACC) - Body ground | Engine switch on (ACC) | 4 to 6 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V20-4 (MCO-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Roof Console Box Sub-assembly (Wire Harness Side)) |
| *b | Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side)) |
Remove the roof console box sub-assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 (MACC) - A-5 (MACC) | Always | Below 1 Ω |
| 5 (MCO+) - A-3 (MIC+) | Always | Below 1 Ω |
| 4 (MCO-) - A-2 (MIC-) | Always | Below 1 Ω |
| 6 (MACC) - 5 (MCO+) | Always | 10 kΩ or higher |
| 6 (MACC) - 4 (MCO-) | Always | 10 kΩ or higher |
| 5 (MCO+) - 4 (MCO-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT