Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for Toyota Connected Services) › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _072211 TELEMATICS _0466472 TELEMATICS SYSTEM(for Toyota Connected Services) C

TELEMATICS  TELEMATICS SYSTEM(for Toyota Connected Services)  B15C464  Airbag Signal Signal Plausibility Failure  


DESCRIPTION

If the telematics transceiver detects an error in communication between the telematics transceiver and the airbag sensor assembly as a result of the telematics transceiver self check, this DTC will be set.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C464 Airbag Signal Signal Plausibility Failure Telematics transceiver detects an error in signals from airbag sensor assembly when ignition switch is ON.
·

Airbag system

·

Harness or connector

·

Airbag sensor assembly

·

Telematics transceiver



WIRING DIAGRAM

B469621E88
1.969,1.073 2.438,1.25 0.469,0.177 10 false GSW3 4.885,1.073 5.323,1.26 0.438,0.188 10 false GSW 1.115,2.063 1.469,2.354 0.354,0.292 10 false K73 1.115,2.229 2.927,2.448 1.813,0.219 10 false Airbag Sensor Assembly 4.448,2.052 5.167,2.271 0.719,0.219 10 false K156 4.448,2.219 6.594,2.552 2.146,0.333 10 false Telematics Transceiver 2.5,1.094 2.76,1.365 0.26,0.271 10 false 23 4.604,1.094 4.771,1.271 0.167,0.177 10 false 13

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CHECK DTC (AIRBAG SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds.


d.

Turn the GTS on.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK DTC

B

2.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK TELEMATICS TRANSCEIVER (GSW SIGNAL)
3.CHECK TELEMATICS TRANSCEIVER (GSW SIGNAL)
a.
E422011C70
1.469,0.219 1.948,0.458 0.479,0.24 0.719,0.375 0.896,0.375 0.896,0.375 1.104,1.104 true 0.135,0.104 0.406,0.365 0.271,0.26 10 false *a 0.323,0.292 0.698,0.438 0.375,0.146 10 false GSW 1.563,0.26 2,0.51 0.438,0.25 10 false K156 0.208,4.031 0.646,4.292 0.438,0.26 10 false GND
*a Component with harness connected
(Telematics Transceiver)


Remove the telematics transceiver but do not disconnect the connectors.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Check the input waveform.

i.

Check the signal waveform according to the condition(s) in the table below. (Check the waveform from the back of the wire harness connector of the telematics transceiver while the airbag sensor assembly connectors are connected.)

Reference Waveform:
Item Condition
Tester connection K156-13 (GSW) - Body ground
Tool setting 5.0 V/DIV., 20 ms./DIV.
Vehicle condition Ignition switch ON


OK:

The waveform is similar to that shown in the illustration.




Result:
Proceed to
OK
NG



OK

4.REPLACE TELEMATICS TRANSCEIVER

NG

5.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - AIRBAG SENSOR ASSEMBLY)
4.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the K156 telematics transceiver connector.


b.

Disconnect the K73 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K156-13 (GSW) - K73-23 (GSW3) Always Below 1 Ω
K156-13 (GSW) or K73-23 (GSW3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR