Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › from 2021.02
RM33A0E _59 Vehicle Exterior _065393 MIRROR (EXT) _0327585 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)

a.

Check the mirror select switch and mirror surface adjust switch. (w/o Power Retract Mirror)

i.
B519680C08
2.021,0.396 1.781,0.396 1.781,0.396 1.781,0.958 true 0.833,2.917 1.302,3.531 true 1.167,2.917 1.458,3.531 true 1.5,2.917 1.625,3.531 true 1.917,2.917 1.781,3.531 true 2.344,2.917 1.958,3.531 true 1.229,4.354 1.469,3.854 true 2.396,4.344 2.115,3.854 true 2.042,0.302 2.354,0.5 0.313,0.198 10 false *a 0.281,3 0.594,3.198 0.313,0.198 10 false *b 0.76,2.75 0.979,2.948 0.219,0.198 10 false B 1.073,2.75 1.406,2.917 0.333,0.167 10 false VR 1.438,2.75 1.771,2.917 0.333,0.167 10 false HL 1.844,2.75 2.177,2.917 0.333,0.167 10 false HR 2.271,2.76 2.604,2.927 0.333,0.167 10 false VL 2.375,4.344 2.708,4.51 0.333,0.167 10 false E 1.125,4.354 1.458,4.521 0.333,0.167 10 false M+
*a Mirror Select and Surface Adjust Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
2 (VL) - 6 (B)
11 (M+) - 7 (E)
Up Below 2 Ω
Off 10 kΩ or higher
2 (VL) - 7 (E)
11 (M+) - 6 (B)
Down Below 2 Ω
Off 10 kΩ or higher
4 (HL) - 6 (B)
11 (M+) - 7 (E)
Left Below 2 Ω
Off 10 kΩ or higher
4 (HL) - 7 (E)
11 (M+) - 6 (B)
Right Below 2 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
5 (VR) - 6 (B)
11 (M+) - 7 (E)
Up Below 2 Ω
Off 10 kΩ or higher
5 (VR) - 7 (E)
11 (M+) - 6 (B)
Down Below 2 Ω
Off 10 kΩ or higher
3 (HR) - 6 (B)
11 (M+) - 7 (E)
Left Below 2 Ω
Off 10 kΩ or higher
3 (HR) - 7 (E)
11 (M+) - 6 (B)
Right Below 2 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check that the LED illuminates. (w/o Power Retract Mirror)

i.
B519680C09
2.115,3.531 2.417,2.927 true 1.052,4.344 1.302,3.854 true 0.938,4.344 1.313,4.542 0.375,0.198 10 false ILL+ 2.333,2.75 2.708,2.948 0.375,0.198 10 false ILL- 0.458,3.01 0.771,3.208 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror Switch Assembly)


Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Battery Connection Specified Condition
Battery positive (+) - 12 (ILL+)
Battery negative (-) - 1 (ILL-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.



c.

Check the mirror select and surface adjust switch. (for LHD with Power Retract Mirror)

i.
B551925C05
1.979,0.969 1.979,0.406 1.979,0.406 2.229,0.406 true 0.917,1.323 0.531,1.323 true 1.281,3.521 0.885,2.938 true 1.458,3.521 1.167,2.917 true 1.625,3.521 1.5,2.917 true 1.792,3.521 1.917,2.917 true 1.958,3.521 2.333,2.917 true 1.469,3.844 1.125,4.365 true 1.625,3.854 1.469,4.354 true 1.781,3.854 1.938,4.344 true 2.115,3.844 2.385,4.365 true 2.25,0.313 2.563,0.51 0.313,0.198 10 false *a 0.365,1.24 0.677,1.438 0.313,0.198 10 false *b 0.375,2.979 0.688,3.177 0.313,0.198 10 false *c 0.813,2.771 1.125,2.969 0.313,0.198 10 false B 1.073,2.76 1.385,2.958 0.313,0.198 10 false VR 1.427,2.75 1.74,2.948 0.313,0.198 10 false HL 1.833,2.76 2.146,2.958 0.313,0.198 10 false HR 2.271,2.76 2.583,2.958 0.313,0.198 10 false VL 2.354,4.365 2.667,4.563 0.313,0.198 10 false E 1.854,4.365 2.271,4.531 0.417,0.167 10 false MF 1.344,4.365 1.76,4.531 0.417,0.167 10 false MR 0.99,4.365 1.406,4.531 0.417,0.167 10 false M+
*a Mirror Select and Surface Adjust Switch
*b Retractable Outer Mirror Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
2 (VL) - 6 (B)
11 (M+) - 7 (E)
Up Below 2 Ω
Off 10 kΩ or higher
2 (VL) - 7 (E)
11 (M+) - 6 (B)
Down Below 2 Ω
Off 10 kΩ or higher
4 (HL) - 6 (B)
11 (M+) - 7 (E)
Left Below 2 Ω
Off 10 kΩ or higher
4 (HL) - 7 (E)
11 (M+) - 6 (B)
Right Below 2 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
5 (VR) - 6 (B)
11 (M+) - 7 (E)
Up Below 2 Ω
Off 10 kΩ or higher
5 (VR) - 7 (E)
11 (M+) - 6 (B)
Down Below 2 Ω
Off 10 kΩ or higher
3 (HR) - 6 (B)
11 (M+) - 7 (E)
Left Below 2 Ω
Off 10 kΩ or higher
3 (HR) - 7 (E)
11 (M+) - 6 (B)
Right Below 2 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



d.

Check the retractable outer mirror switch. (for LHD with Power Retract Mirror)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (MF) - 6 (B)
10 (MR) - 7 (E)
Driving position Below 2 Ω
10 (MR) - 6 (B)
9 (MF) - 7 (E)
Retract position Below 2 Ω


If the result is not as specified, replace the outer mirror switch assembly.



e.

Check that the LED illuminates. (for LHD with Power Retract Mirror)

i.
B551925C06
2.125,3.521 2.5,2.917 true 1.073,4.333 1.313,3.844 true 0.563,3 0.875,3.198 0.313,0.198 10 false *a 0.948,4.333 1.26,4.531 0.313,0.198 10 false ILL+ 2.417,2.76 2.729,2.958 0.313,0.198 10 false ILL-
*a Component without harness connected
(Outer Mirror Switch Assembly)


Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Battery Connection Specified Condition
Battery positive (+) - 12 (ILL+)
Battery negative (-) - 1 (ILL-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.



f.

Check the mirror select and surface adjust switch. (for RHD with Power Retract Mirror)

i.
B551414C05
1.406,0.896 1.406,0.333 1.406,0.333 1.656,0.333 true 2.875,1.25 2.49,1.25 true 1.281,3.521 0.885,2.938 true 1.458,3.521 1.167,2.917 true 1.625,3.521 1.5,2.917 true 1.792,3.531 1.917,2.927 true 1.958,3.531 2.333,2.927 true 1.469,3.844 1.125,4.365 true 1.625,3.854 1.469,4.354 true 1.781,3.854 1.938,4.344 true 2.115,3.844 2.385,4.365 true 1.677,0.229 1.99,0.427 0.313,0.198 10 false *a 2.885,1.156 3.198,1.354 0.313,0.198 10 false *b 0.375,2.979 0.688,3.177 0.313,0.198 10 false *c 0.813,2.771 1.125,2.969 0.313,0.198 10 false B 1.073,2.76 1.385,2.958 0.313,0.198 10 false VR 1.427,2.75 1.74,2.948 0.313,0.198 10 false HL 1.833,2.76 2.146,2.958 0.313,0.198 10 false HR 2.271,2.771 2.583,2.969 0.313,0.198 10 false VL 2.354,4.365 2.667,4.563 0.313,0.198 10 false E 1.854,4.365 2.271,4.531 0.417,0.167 10 false MF 1.344,4.365 1.76,4.531 0.417,0.167 10 false MR 0.99,4.365 1.406,4.531 0.417,0.167 10 false M+
*a Mirror Select and Surface Adjust Switch
*b Retractable Outer Mirror Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
2 (VL) - 6 (B)
11 (M+) - 7 (E)
Up Below 2 Ω
Off 10 kΩ or higher
2 (VL) - 7 (E)
11 (M+) - 6 (B)
Down Below 2 Ω
Off 10 kΩ or higher
4 (HL) - 6 (B)
11 (M+) - 7 (E)
Left Below 2 Ω
Off 10 kΩ or higher
4 (HL) - 7 (E)
11 (M+) - 6 (B)
Right Below 2 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
5 (VR) - 6 (B)
11 (M+) - 7 (E)
Up Below 2 Ω
Off 10 kΩ or higher
5 (VR) - 7 (E)
11 (M+) - 6 (B)
Down Below 2 Ω
Off 10 kΩ or higher
3 (HR) - 6 (B)
11 (M+) - 7 (E)
Left Below 2 Ω
Off 10 kΩ or higher
3 (HR) - 7 (E)
11 (M+) - 6 (B)
Right Below 2 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



g.

Check the retractable outer mirror switch. (for RHD with Power Retract Mirror)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (MF) - 6 (B)
10 (MR) - 7 (E)
Driving position Below 2 Ω
10 (MR) - 6 (B)
9 (MF) - 7 (E)
Retract position Below 2 Ω


If the result is not as specified, replace the outer mirror switch assembly.



h.

Check that the LED illuminates. (for RHD with Power Retract Mirror)

i.
B551414C06
2.125,3.531 2.5,2.927 true 1.073,4.344 1.313,3.854 true 0.563,3 0.875,3.198 0.313,0.198 10 false *a 0.948,4.344 1.26,4.542 0.313,0.198 10 false ILL+ 2.417,2.76 2.729,2.958 0.313,0.198 10 false ILL-
*a Component without harness connected
(Outer Mirror Switch Assembly)


Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Battery Connection Specified Condition
Battery positive (+) - 12 (ILL+)
Battery negative (-) - 1 (ILL-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.



i.

Check the mirror select and surface adjust switch. (for LHD with Automatic Retractable Mirror)

i.
E398173C17
1.979,0.969 1.979,0.375 1.979,0.375 2.302,0.375 true 0.917,1.323 0.531,1.323 true 1.292,3.521 0.917,2.917 true 1.458,3.521 1.167,2.917 true 1.615,3.521 1.49,2.917 true 1.792,3.521 1.917,2.917 true 1.948,3.531 2.323,2.927 true 1.458,3.844 1.125,4.365 true 1.625,3.854 1.448,4.354 true 1.781,3.854 1.906,4.344 true 1.948,3.854 2.25,4.333 true 2.115,3.854 2.5,4.333 true 2.323,0.281 2.635,0.479 0.313,0.198 10 false *a 0.365,1.24 0.677,1.438 0.313,0.198 10 false *b 0.438,3.021 0.75,3.219 0.313,0.198 10 false *c 0.854,2.76 1.167,2.958 0.313,0.198 10 false B 1.063,2.76 1.375,2.958 0.313,0.198 10 false VR 1.406,2.75 1.719,2.948 0.313,0.198 10 false HL 1.823,2.76 2.135,2.958 0.313,0.198 10 false HR 2.271,2.76 2.583,2.958 0.313,0.198 10 false VL 2.479,4.354 2.792,4.552 0.313,0.198 10 false E 2.208,4.354 2.521,4.552 0.313,0.198 10 false E 1.781,4.365 2.198,4.531 0.417,0.167 10 false MAT 1.344,4.365 1.76,4.531 0.417,0.167 10 false MR 1.01,4.365 1.427,4.531 0.417,0.167 10 false M+
*a Mirror Select and Surface Adjust Switch
*b Retractable Outer Mirror Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
2 (VL) - 6 (B)
11 (M+) - 7 (E)
Up Below 2 Ω
Off 10 kΩ or higher
2 (VL) - 7 (E)
11 (M+) - 6 (B)
Down Below 2 Ω
Off 10 kΩ or higher
4 (HL) - 6 (B)
11 (M+) - 7 (E)
Left Below 2 Ω
Off 10 kΩ or higher
4 (HL) - 7 (E)
11 (M+) - 6 (B)
Right Below 2 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
5 (VR) - 6 (B)
11 (M+) - 7 (E)
Up Below 2 Ω
Off 10 kΩ or higher
5 (VR) - 7 (E)
11 (M+) - 6 (B)
Down Below 2 Ω
Off 10 kΩ or higher
3 (HR) - 6 (B)
11 (M+) - 7 (E)
Left Below 2 Ω
Off 10 kΩ or higher
3 (HR) - 7 (E)
11 (M+) - 6 (B)
Right Below 2 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



j.

Check the retractable outer mirror switch. (for LHD with Automatic Retractable Mirror)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (MAT) - 8 (E) AUTO position Below 35 Ω
Except AUTO position 10 kΩ or higher
10 (MR) - 8 (E) Retract position Below 35 Ω
Except retract position 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



k.

Check that the LED illuminates. (for LHD with Automatic Retractable Mirror)

i.
E398173C18
2.125,3.531 2.5,2.927 true 1.01,4.344 1.302,3.854 true 0.531,2.99 0.844,3.188 0.313,0.198 10 false *a 0.885,4.333 1.198,4.531 0.313,0.198 10 false ILL+ 2.427,2.76 2.74,2.958 0.313,0.198 10 false ILL-
*a Component without harness connected
(Outer Mirror Switch Assembly)


Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Battery Connection Specified Condition
Battery positive (+) - 12 (ILL+)
Battery negative (-) - 1 (ILL-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)

a.

Check the mirror select and surface adjust switch.

i.
E398173C15
1.979,0.969 1.979,0.375 1.979,0.375 2.271,0.375 true 0.865,1.313 0.531,1.313 true 1.458,3.542 1.177,2.896 true 1.625,3.531 1.865,2.906 true 1.625,3.844 1.417,4.333 true 1.781,3.854 1.906,4.344 true 1.948,3.854 2.25,4.333 true 2.115,3.854 2.5,4.333 true 2.292,0.281 2.604,0.479 0.313,0.198 10 false *a 0.365,1.229 0.677,1.427 0.313,0.198 10 false *b 0.635,2.979 0.948,3.177 0.313,0.198 10 false *c 0.969,2.74 1.458,2.938 0.49,0.198 10 false MSW 1.792,2.74 2.104,2.938 0.313,0.198 10 false M+ 2.479,4.344 2.792,4.542 0.313,0.198 10 false E 2.188,4.354 2.5,4.552 0.313,0.198 10 false E2 1.771,4.365 2.188,4.531 0.417,0.167 10 false MAT 1.313,4.365 1.729,4.531 0.417,0.167 10 false MR
*a Mirror Select and Surface Adjust Switch
*b Retractable Outer Mirror Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
4 (M+) - 7 (E) Up 90 to 110 Ω
Down 437 to 503 Ω
Left 744 to 856 Ω
Right 225 to 275 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
4 (M+) - 7 (E) Up 90 to 110 Ω
Down 437 to 503 Ω
Left 744 to 856 Ω
Right 225 to 275 Ω
Off 10 kΩ or higher



v.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (MSW) - 7 (E) Turn the mirror select switch to the L position 90 to 110 Ω
Turn the mirror select switch to the R position Below 10 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the retractable outer mirror switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (MAT) - 8 (E2) AUTO position Below 35 Ω
Except AUTO position 10 kΩ or higher
10 (MR) - 8 (E2) Retract position Below 35 Ω
Except retract position 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

Check that the LED illuminates.

i.
E398173C16
2.115,3.531 2.49,2.927 true 1.073,4.323 1.313,3.854 true 0.594,3.031 0.906,3.229 0.313,0.198 10 false *a 0.958,4.333 1.271,4.531 0.313,0.198 10 false ILL+ 2.427,2.76 2.74,2.958 0.313,0.198 10 false ILL-
*a Component without harness connected
(Outer Mirror Switch Assembly)


Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Battery Connection Specified Condition
Battery positive (+) - 12 (ILL+)
Battery negative (-) - 1 (ILL-)
LED illuminates


If the result is not as specified, replace the outer mirror switch assembly.