FREEZE FRAME DATA
When a DTC is stored, the freeze frame data stores the current vehicle (sensor) state as.
The freeze frame data cannot be cleared or updated until the recorded DTCs are cleared.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| IG1 Voltage Value | IG1 terminal voltage value (value detected by ECU) | Min.: 0.0 V, Max.: 25.5 V | Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to battery voltage |
| BS1 Voltage Value | +BS terminal voltage value (value detected by ECU) | Min.: 0.0 V, Max.: 25.5 V | Ignition switch ON: 11.0 to 14.0 V | Changes in proportion to battery voltage |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Forward and Rearward G | Forward and rearward G | Min.: -25.105 m/s2, Max.: 24.908 m/s2 | During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%, Max.: 127.5% | Accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Shift Lever Position | Shift lever position information | fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input | Actual shift lever position | - |
| Brake Hold Control Mode | Brake hold control mode | Out of control mode /
Pressure hold mode / Pressure release mode / EPB lock mode |
Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)
Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated) Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated) EPB lock mode: Parking brake is engaged during brake hold control |
|
| Vehicle Speed | Vehicle speed (vehicle speed used for each control) | Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) | Vehicle stopped: 0.0 km/h (0.0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed Grade | Vehicle speed grade | Min.: -25.105 m/s2, Max.: 24.908 m/s2 | Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During deceleration/acceleration: Changes continuously |
| IG Switch | Ignition switch ON status | OFF / ON | - | - |
| Parking Brake SW | Parking brake switch assembly | OFF / ON | OFF: Parking brake released
ON: Parking brake applied |
- |
| EFI Communication Open | ECM communication open detection | Error / Normal | Error: Momentary interruption
Normal: Normal |
- |
| Deceleration Open | Acceleration sensor open detection | Error / Normal | Error: Momentary interruption
Normal: Normal |
- |
| ECU +B1 Voltage | Skid control ECU (brake actuator assembly) +B1 voltage | Min.: 0.0 V, Max.: 25.5 V | 11 to 14 V | - |
| RH Actuator Motor Input Voltage | Parking brake motor RH (parking brake actuator assembly RH) input voltage | Min.: 0.0 V, Max.: 25.5 V | - | - |
| LH Actuator Motor Input Voltage | Parking brake motor LH (parking brake actuator assembly LH) input voltage | Min.: 0.0 V, Max.: 25.5 V | - | - |
| RH Actuator Motor +Terminal Voltage | Parking brake motor RH (parking brake actuator assembly RH) positive (+) terminal side voltage | Min.: 0.0 V, Max.: 25.5 V | - | - |
| LH Actuator Motor +Terminal Voltage | Parking brake motor LH (parking brake actuator assembly LH) positive (+) terminal side voltage | Min.: 0.0 V, Max.: 25.5 V | - | - |
| RH Actuator Motor -Terminal Voltage | Parking brake motor RH (parking brake actuator assembly RH) negative (-) terminal side voltage | Min.: 0.0 V, Max.: 25.5 V | - | - |
| LH Actuator Motor -Terminal Voltage | Parking brake motor LH (parking brake actuator assembly LH) negative (-) terminal side voltage | Min.: 0.0 V, Max.: 25.5 V | - | - |
| EPB Switch | Electric parking brake switch input | OFF / Lock / Release / Unknown | OFF: Lock switch and release switch are off
Lock: Lock switch on Release: Release switch on |
When not normal, electric parking brake switch release side system may be malfunctioning
|
| RH Actuator Motor Actual Current | Parking brake motor RH (parking brake actuator assembly RH) current value | Min.: -5.0362 A, Max.: 50.5004 A | - | - |
| LH Actuator Motor Actual Current | Parking brake motor LH (parking brake actuator assembly LH) current value | Min.: -5.0362 A, Max.: 50.5004 A | - | - |
| RH Actuator Status | Parking brake actuator assembly RH condition | Park Applied / Hold Applied / Released / Applying / Releasing / Completely Released / Unknown | - | - |
| LH Actuator Status | Parking brake actuator assembly LH condition | Park Applied / Hold Applied / Released / Applying / Releasing / Completely Released / Unknown | - | - |
| EPB Warning Light | Brake system warning light (yellow indicator) output signal | OFF / ON | OFF: Brake system warning light (yellow indicator) turns off
ON: Brake system warning light (yellow indicator) illuminates |
- |
| Auto Mode Request | Auto mode request status | OFF / ON | - | - |
| Brake Hold Ready | Brake hold control permission status | Not in stand-by mode / Stand-by mode | Not in stand-by mode: Brake hold function not operating (brake hold indicator not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold indicator illuminated) |
- |
| EPB Lock Request | Lock demand status | OFF / ON | OFF: Not requested
ON: Requested |
|
| Auto Mode | AUTO (shift-linked) mode permission status | OFF / ON | OFF: Manual mode.
ON: AUTO (shift-linked) mode |
- |
| Dynamic PKB Mode | Dynamic parking brake operation status | OFF / ON | OFF: Dynamic parking brake is not operating
ON: Dynamic parking brake is operating |
- |
| RH Actuator Motor Relay1 | Parking brake motor relay 1 RH condition | OFF / ON | - | - |
| RH Actuator Motor Relay2 | Parking brake motor relay 2 RH condition | OFF / ON | - | - |
| RH Actuator Motor Relay3 | Parking brake motor relay 3 RH condition | OFF / ON | - | - |
| RH Actuator Motor Relay4 | Parking brake motor relay 4 RH condition | OFF / ON | - | - |
| LH Actuator Motor Relay1 | Parking brake motor relay 1 LH condition | OFF / ON | - | - |
| LH Actuator Motor Relay2 | Parking brake motor relay 2 LH condition | OFF / ON | - | - |
| LH Actuator Motor Relay3 | Parking brake motor relay 3 LH condition | OFF / ON | - | - |
| LH Actuator Motor Relay4 | Parking brake motor relay 4 LH condition | OFF / ON | - | - |
| RH Actuator Current Status | Parking brake actuator assembly RH monitoring current condition | Normal / Invalid | - | - |
| LH Actuator Current Status | Parking brake actuator assembly LH monitoring current condition | Normal / Invalid | - | - |
| Permission of RH Interlocking PKB Lock | Parking brake actuator assembly RH parking brake lock control permission status | Available / Not available | - | - |
| Permission of RH Interlocking PKB Release | Parking brake actuator assembly RH parking brake release control permission status | Available / Not available | - | - |
| Permission of RH Interlocking Dynamic PKB | Parking brake actuator assembly RH dynamic parking control permission status | Available / Not available | - | - |
| Permission of RH Interlocking PKB Full Release | Parking brake actuator assembly RH parking brake full release permission status | Available / Not available | - | - |
| Permission of LH Interlocking PKB Lock | Parking brake actuator assembly LH parking brake lock control permission status | Available / Not available | - | - |
| Permission of LH Interlocking PKB Release | Parking brake actuator assembly LH parking brake release control permission status | Available / Not available | - | - |
| Permission of LH Interlocking Dynamic PKB | Parking brake actuator assembly LH dynamic parking control permission status | Available / Not available | - | - |
| Permission of LH Interlocking PKB Full Release | Parking brake actuator assembly LH parking brake full release permission status | Available / Not available | - | - |
| RH Actuator Motor Current High | Parking brake motor RH (parking brake actuator assembly RH) overcurrent status | OFF / ON | - | - |
| RH Actuator Motor Driver Operation Status | Parking brake motor RH (parking brake actuator assembly RH) driver status | OFF / ON | - | - |
| LH Actuator Motor Current High | Parking brake motor LH (parking brake actuator assembly LH) overcurrent status | OFF / ON | - | - |
| LH Actuator Motor Driver Operation Status | Parking brake motor LH (parking brake actuator assembly LH) driver status | OFF / ON | - | - |
Using the GTS, the state of the vehicle (sensors) when the system is operating or when a DTC was stored can be checked.