Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › from 2021.02
RM33A0E _54 Brake _065369 PARKING BRAKE _0328504 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C060B00  Left Electric Parking Brake Actuator Control  C060B11  Left Electric Parking Brake Actuator Control Circuit Short to Ground  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C060B00 Left Electric Parking Brake Actuator Control
·

Diagnosis Condition:

-

·

Malfunction Status:

When the ECU power supply is normal, a malfunction in the electric parking brake actuator LH internal circuit is detected.

·

Detection Time:

-


·

Parking brake actuator assembly LH

·

No. 2 parking brake wire assembly

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the combination meter assembly.
C060B11 Left Electric Parking Brake Actuator Control Circuit Short to Ground
·

Diagnosis Condition:

Electric parking brake not operating

·

Malfunction Status:

The ECU power supply is normal but there is a malfunction in the electric parking brake actuator LH internal circuit (short to GND).

·

Detection Time:

Approximately 0.015 to 0.195 seconds (depending on each malfunction)


·

Parking brake actuator assembly LH

·

No. 2 parking brake wire assembly

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the combination meter assembly.

WIRING DIAGRAM

C402632E95
1.313,0.677 1.927,0.875 0.615,0.198 10 false MRL+ 1.344,1.281 1.958,1.479 0.615,0.198 10 false MRL- 3.625,0.698 4.083,0.896 0.458,0.198 10 false vR2 5.031,1.094 5.208,1.365 0.177,0.271 10 false 1 3.677,1.083 3.854,1.354 0.177,0.271 10 false 1 3.656,0.49 3.833,0.76 0.177,0.271 10 false 2 5.021,0.5 5.198,0.771 0.177,0.271 10 false 2 5.323,0.688 5.781,0.927 0.458,0.24 10 false LE+ 5.333,1.281 5.792,1.479 0.458,0.198 10 false LE- 5.01,0.688 5.323,0.885 0.313,0.198 10 false v1 5.281,1.802 6.75,2.198 1.469,0.396 10 false Parking Brake Actuator Assembly LH 3.708,1.802 4.979,2.354 1.271,0.552 10 false No. 2 Parking Brake Wire Assembly 0.583,1.792 1.042,1.99 0.458,0.198 10 false A34 0.583,1.948 2.135,2.396 1.552,0.448 10 false Skid Control ECU (Brake Actuator Assembly) 1.792,0.583 2.104,0.781 0.313,0.198 10 false 13 1.792,1.177 2.104,1.375 0.313,0.198 10 false 12 3.625,1.292 4.083,1.49 0.458,0.198 10 false vR2 5.01,1.292 5.323,1.49 0.313,0.198 10 false v1

PROCEDURE

1.INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the vR2 and v1 No. 2 parking brake wire assembly connectors.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

C447665C32
1.729,0.333 2.146,0.583 0.417,0.25 4.833,0.333 5.25,0.583 0.417,0.25 5.26,1.802 5.677,2.302 5.677,2.302 5.927,2.302 true 4.833,1.802 4.417,2.302 4.417,2.302 4.167,2.302 true 1.802,0.365 2.26,0.563 0.458,0.198 10 false vR2 4.958,0.365 5.417,0.563 0.458,0.198 10 false v1 6,2.219 6.417,2.469 0.417,0.25 10 false LE+ 3.885,2.208 4.344,2.406 0.458,0.198 10 false LE- 1.875,2.25 2.333,2.458 0.458,0.208 10 false *b 0.125,0.125 0.656,0.365 0.531,0.24 10 false *a 4.979,2.25 5.438,2.448 0.458,0.198 10 false *c
*a Front view of No. 2 Parking Brake Wire Assembly *b to wire harness connector
*c to Parking Brake Actuator Assembly LH - -


Standard Resistance:
Tester Connection Condition Specified Condition
vR2-2 or v1-2 (LE+) - Body ground and other terminals Always 10 kΩ or higher
vR2-1 or v1-1 (LE-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)

NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)
a.

Turn the ignition switch off.


b.

Make sure the No. 2 parking brake wire assembly is securely installed.


c.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the v1 parking brake actuator assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-13 (MRL+) or v1-2 (LE+) - Body ground Always 10 kΩ or higher
A34-12 (MRL-) or v1-1 (LE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY LH
a.

Remove the parking brake actuator assembly LH.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


b.

Inspect the parking brake actuator assembly LH.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY LH