Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › from 2021.02
RM33A0E _54 Brake _065369 PARKING BRAKE _0328504 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C061013  Right Electric Parking Brake Actuator Control Circuit Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C061013 Right Electric Parking Brake Actuator Control Circuit Open
·

Diagnosis Condition:

Electric parking brake not operating

·

Malfunction Status:

The ECU power supply is normal but there is a malfunction in the electric parking brake actuator RH internal circuit (open).

·

Detection Time:

Approximately 0.015 to 0.195 seconds (depending on each malfunction)


·

Parking brake actuator assembly RH

·

No. 1 parking brake wire assembly

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the combination meter assembly.

PROCEDURE

1.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the uR2 and u1 No. 1 parking brake wire assembly connectors.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

C447665C33
1.729,0.333 2.146,0.583 0.417,0.25 4.844,0.333 5.26,0.583 0.417,0.25 5.26,1.813 5.677,2.313 5.677,2.313 5.927,2.313 true 4.833,1.802 4.417,2.302 4.417,2.302 4.167,2.302 true 1.813,0.396 2.271,0.594 0.458,0.198 10 false uR2 4.969,0.385 5.427,0.583 0.458,0.198 10 false u1 6.01,2.219 6.427,2.469 0.417,0.25 10 false RE+ 3.865,2.208 4.323,2.406 0.458,0.198 10 false RE- 1.896,2.25 2.354,2.458 0.458,0.208 10 false *b 0.125,0.125 0.656,0.365 0.531,0.24 10 false *a 4.99,2.25 5.448,2.448 0.458,0.198 10 false *c
*a Front view of No. 1 Parking Brake Wire Assembly *b to wire harness connector
*c to Parking Brake Actuator Assembly RH - -


Standard Resistance:
Tester Connection Condition Specified Condition
uR2-2 - u1-2 (RE+) Always Below 1 Ω
uR2-2 - Other terminals Always 10 kΩ or higher
uR2-1 - u1-1 (RE-) Always Below 1 Ω
uR2-1 - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)
a.

Turn the ignition switch off.


b.

Make sure the No. 1 parking brake wire assembly is securely installed.


c.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the u1 parking brake actuator assembly RH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-2 (MRR+) - u1-2 (RE+) Always Below 1 Ω
A34-3 (MRR-) - u1-1 (RE-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH
a.

Remove the parking brake actuator assembly RH.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL


b.

Inspect the parking brake actuator assembly RH.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE PARKING BRAKE ACTUATOR ASSEMBLY RH