Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear) › from 2021.02
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0328090 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
w/o Parking Support Brake System:

Ultrasonic sensor


Initialization of ultrasonic sensors TOYOTA Parking Assist-sensor System (Click here)
w/ Parking Support Brake System:

Ultrasonic sensor


·

Measure ultrasonic sensor detection angle

·

Register ultrasonic sensor detection angle


·

TOYOTA Parking Assist-sensor System

·

Parking Support Brake System


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR BUMPER ASSEMBLY

Hide 89342 2.REMOVE REAR CORNER ULTRASONIC SENSOR (w/o Parking Support Brake System)

a.
E459849C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


b.

Disengage the claw as shown in the illustration.


c.
E459851C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the rear corner ultrasonic sensor as shown in the illustration.


Hide 89342A 3.REMOVE REAR CENTER ULTRASONIC SENSOR (w/o Parking Support Brake System)

a.

for 6 Sensor Type:

i.
E459859C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


ii.

Disengage the claw as shown in the illustration.


iii.
E459861C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the rear center ultrasonic sensor as shown in the illustration.



Hide 89348J 4.REMOVE ULTRASONIC SENSOR CLIP (w/o Parking Support Brake System)

HINT:

Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.


a.
E459853

Disengage the clamp to remove the ultrasonic sensor clip from the wire.


Hide 89348R 5.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER (w/o Parking Support Brake System)

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

When removing the rear corner ultrasonic sensor retainer, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.



a.

Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E459854

Remove the rear corner ultrasonic sensor retainer.


Hide 89348S 6.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER (w/o Parking Support Brake System)

a.

for 6 Sensor Type:

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

When removing the rear center ultrasonic sensor retainer, heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.



i.

Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Center Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




ii.
E459863

Remove the rear center ultrasonic sensor retainer.



Hide 89342A 7.REMOVE REAR CENTER ULTRASONIC SENSOR (w/ Parking Support Brake System)

a.
E459880C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


b.

Disengage the 4 claws as shown in the illustration.


c.
E459882C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the rear center ultrasonic sensor as shown in the illustration.


Hide 89342 8.REMOVE REAR CORNER ULTRASONIC SENSOR (w/ Parking Support Brake System)

a.
E459887C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector.


b.

Disengage the 4 claws as shown in the illustration.


c.
E459889C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the rear corner ultrasonic sensor as shown in the illustration.


Hide 89348J 9.REMOVE ULTRASONIC SENSOR CLIP (w/ Parking Support Brake System)

HINT:
·

Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.

·

Use the same procedure for all ultrasonic sensor clips.



a.
E459894

Disengage the clamp to remove the ultrasonic sensor clip from the wire.


Hide 89348S 10.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

When removing the rear center ultrasonic sensor retainer, heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.



a.

Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Center Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E459884

Remove the rear center ultrasonic sensor retainer.


Hide 89348R 11.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER (w/ Parking Support Brake System)

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

When removing the rear corner ultrasonic sensor retainer, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.



a.

Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.

Heating Temperature:
Item Temperature
Rear Bumper Assembly 40 to 60°C (104 to 140°F)
Rear Corner Ultrasonic Sensor Retainer


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.




b.
E459891

Remove the rear corner ultrasonic sensor retainer.


Hide 89305 12.REMOVE ULTRASONIC SENSOR CUSHION SET

HINT:

Only perform this procedure when removing and installing the ultrasonic sensor cushion set.


a.

Remove the ultrasonic sensor cushion set as shown in the illustration.

E488344C01
0,0 0,0 false
V113147

Remove in this Direction - -