Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2021.02
RM33A0E _58 Vehicle Interior _065381 METER / GAUGE / DISPLAY _0323396 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B132187  Lost Communication with EMV Missing Message  


DESCRIPTION

The combination meter assembly and radio and display receiver assembly communicate via local bus communication. This allows audio and visual system or navigation system information to be displayed on the multi-information display.

This DTC is stored when a communication error occurs between the radio and display receiver assembly and combination meter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B132187 Lost Communication with EMV Missing Message Diagnosis Condition:
·

The ignition switch is ON

·

IG power source voltage is 9.5 V or more


Malfunction Status:

No communication with radio and display receiver assembly


Malfunction Time:

3.0 seconds or more


·

Harness or connector

·

Radio and display receiver assembly

·

Meter mirror sub-assembly*

·

Combination meter assembly


w/ Radio and Display Receiver Assembly

*: w/ Headup Display System


WIRING DIAGRAM

E369856E03
5.042,1.458 6.906,1.698 1.865,0.24 10 false Combination Meter Assembly 0.917,1.448 3.292,1.688 2.375,0.24 10 false Radio and Display Receiver Assembly 0.99,3.021 2.74,3.229 1.75,0.208 10 false Meter Mirror Sub-assembly* 0.927,3.365 3.073,3.573 2.146,0.208 10 false : Local Bus Communication Line 0.99,2.833 1.188,3.01 0.198,0.177 10 false p1 0.927,1.292 1.229,1.5 0.302,0.208 10 false K2 5.052,1.292 5.354,1.5 0.302,0.208 10 false K21 5.271,0.344 5.594,0.521 0.323,0.177 10 false TX+ 5.281,0.75 5.604,0.927 0.323,0.177 10 false TX- 2.115,0.479 2.521,0.688 0.406,0.208 10 false CNH1 2.135,0.896 2.542,1.104 0.406,0.208 10 false CNL1 2.26,2.406 2.667,2.615 0.406,0.208 10 false TX- 2.24,1.958 2.583,2.156 0.344,0.198 10 false TX+ 4.979,0.344 5.177,0.583 0.198,0.24 10 false 36 4.99,0.75 5.292,0.958 0.302,0.208 10 false 37 4.719,2.875 6.802,3.104 2.083,0.229 10 false *: w/ Headup Display System 2.625,0.344 2.823,0.583 0.198,0.24 10 false 5 2.625,0.75 2.823,0.99 0.198,0.24 10 false 6 2.604,1.865 3.01,2.073 0.406,0.208 10 false 14 2.604,2.281 3.01,2.49 0.406,0.208 10 false 15 5.948,0.646 6.448,0.875 0.5,0.229 10 false CAN I/F


CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/o Navigation System A
w/ Navigation System B



A

2.CHECK FOR DTC (AUDIO AND VISUAL SYSTEM)

B

3.CHECK FOR DTC (NAVIGATION SYSTEM)
2.CHECK FOR DTC (AUDIO AND VISUAL SYSTEM)
a.

Check if audio and visual system DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are not output
(w/ Headup Display System)
A
DTCs are not output
(w/o Headup Display System)
B
DTCs are output C



A

4.CHECK FOR DTC (HEADUP DISPLAY SYSTEM)

B

5.REPLACE COMBINATION METER ASSEMBLY

C

3.CHECK FOR DTC (NAVIGATION SYSTEM)
a.

Check if navigation system DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are not output
(w/ Headup Display System)
A
DTCs are not output
(w/o Headup Display System)
B
DTCs are output C



A

4.CHECK FOR DTC (HEADUP DISPLAY SYSTEM)

B

5.REPLACE COMBINATION METER ASSEMBLY

C

4.CHECK FOR DTC (HEADUP DISPLAY SYSTEM)
a.

Check if headup display system DTCs are output.

Body Electrical > Head Up Display > Trouble Codes
50001 408

Result:
Result Proceed to
DTC B132187 is not output A
DTC B132187 is output B



A

REPLACE COMBINATION METER ASSEMBLY

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Turn the ignition switch to ON and wait 3 seconds.

NOTICE:

A minimum of 3 seconds is required to send/receive the registration information between the combination meter assembly and radio and display receiver assembly.



c.

Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check if meter / gauge system DTCs are output.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
The audio tab illuminates and DTC B132187 is not output A
The audio tab does not illuminate and DTC B132187 is output B



A

END (COMBINATION METER ASSEMBLY WAS DEFECTIVE)

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY