Home › Engine / Hybrid System › 2GR-FKS (FUEL) › FUEL PUMP (for High Pressure) › from 2021.02
RM33A0E _51 Engine / Hybrid System _065334 2GR-FKS FUEL _0319420 FUEL PUMP(for High Pressure) A

2GR-FKS FUEL  FUEL PUMP(for High Pressure)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
·

Replacement of fuel pump assembly

·

Replacement of fuel injector assembly (for Port Injection)

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 23214A 5.REMOVE FUEL PUMP PROTECTOR

a.
A406558

Disengage the clamp to disconnect the fuel tube sub-assembly from the fuel pump protector.


b.
A406559

Remove the 2 bolts and fuel pump protector from the cylinder head sub-assembly.


Hide 6.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A406560

Disconnect the No. 2 fuel tube sub-assembly from the fuel pump assembly.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23801P 7.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

CAUTION:

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.


a.
A406561

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


b.
A406563

Loosen the 2 bolts of the fuel pump assembly.


c.

Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe RH and fuel pump assembly.


Hide 23100X 8.REMOVE FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY

a.
A406564

Disconnect the fuel pump assembly connector.


b.
A406565

Remove the 2 bolts, fuel pump assembly and fuel pump lifter guide from the cylinder head cover sub-assembly.


c.
A400605

Remove the O-ring from the fuel pump assembly.


d.
A406566

Remove the fuel pump lifter assembly from the fuel pump lifter housing.


e.
A406567

Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly.